ETC Source 4WRD Manuale utente

Source 4WRD Color

Retrofit

Installation and User Manual

Version 1.0.0

Part Number: 7068M1200-1.0.0 Rev A

Released: 2020-09

To view a list of ETCtrademarks and patents, go to

etcconnect.com/ip. All other trademarks, both marked and not

marked, are the property of their respective owners.

ETC intends this document, whether printed or electronic, to be

provided in its entirety.

Table of Contents

Source 4WRD Color Installation and User Manual i

Introduction 1

Help from ETC Technical Services 2

Safety 3

Retrofit the Fixture 5

Wire the Power Connector(If Needed) 5

Remove Incandescent Lamp Housing 6

Install the Source 4WRD Color Retrofit 6

Install Diffusion on Reflector 8

Install the Fixture 10

Attach C-clamp and Safety Cable 10

Connect Cables 11

Configure the Fixture 12

Set the DMXAddress 12

Play Presets and Sequences 13

Data Loss Behavior 14

RDMValues 14

Focus the Fixture 15

Set the Z-adjustment 15

Adjust the Yoke Position 15

Shape the Beam 16

Troubleshoot the Source 4WRD Color 17

Restore Factory Defaults 17

Update the Fixture Software 18

Clean and Maintain the Fixture 19

Clean the Fixture 19

Store the Retrofit 19

Clean the Lenses 20

Clean the Reflector 21

Clean 5° and 10° Polymer Lenses 22

Specifications 23

Electrical 23

Environment 23

Weight 23

Optical 23

ii Source 4WRD Color Installation and User Manual

Source 4WRD Color Installation and User Manual 1

Introduction

The Source 4WRD Color is a replacement for a standard Source Four

burner assembly. It converts the HPL source to an RGBA (red, green, blue,

and amber) LED and provides a significant reduction in power

consumption. The Source 4WRD Color uses DMX dimming and requires

power from a non-dimmable source. When not using DMX, you can use

any of the 12presets or 5sequences on the Source 4WRD Color.

The Source 4WRD Color can also be used with the Source 4WRD PAR or

PARNel Fixture Body to create a Source 4WRD Color PAR or PARNel

fixture. For best results, we recommend that you use the included

diffusion on the Source 4WRD PAR or PARNel Fixture Body when paired

with the Source 4WRD Color. For more information, see the Source 4WRD

Color PAR and PARNel datasheet at etcconnect.com.

Retrofit kit,

shown installed

on a Source Four

fixture body

Note:

The Source 4WRD Color retrofit kit is not compatible with

Source Four LED, Fresnel, PAR, PARNel, or jr fixtures.

2 Source 4WRD Color Installation and User Manual

Help from ETC Technical Services

If you are having difficulties and your problem is not addressed by this

document, try the ETC support website at support.etcconnect.com or the

main ETC website at etcconnect.com. If none of these resources are

sufficient, contact ETC Technical Services directly at one of the offices

identified below. Emergency service is available from all ETC offices

outside of normal business hours.

When calling for help, take these steps first:

•

Prepare a detailed description of the problem

•

Go near the equipment for troubleshooting

•

Find your notification number if you have called in previously

Americas United Kingdom

ETC, Inc. ETC Ltd

Technical Services Department Technical Services Department

3031 Pleasant View Road 26-28 Victoria Industrial Estate

Middleton, WI 53562 Victoria Road,

800-775-4382 (USA, toll-free) London W3 6UU England

+1-608 831-4116 +44 (0)20 8896 1000

service@etcconnect.com techservltd@etcconnect.com

Asia Germany

ETCAsia ETC GmbH

Technical Services Department Technical Services Department

Room 1801, 18/F Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square 83607 Holzkirchen, Germany

9 Sheung Yuet Road +49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong techserv-germany@etcconnect.com

+852 2799 1220

techserv-asia@etcconnect.com

France

ETC France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

techservltd@etcconnect.com

Source 4WRD Color Installation and User Manual 3

Safety

The Source 4WRD Color fixture is intended for professional use only.

Read the entire manual before using this equipment.

WARNING: Note the following safety warnings before use:

•

Do not mount the fixture on or near a flammable

surface.

•

Do not use this fixture with a damaged power lead. If

the power lead (cord set) is damaged, it must be

replaced.

•

Mount and support the fixture only by the primary

suspension holes in the yoke.

•

Suspend the fixture from a suitable structure using only

hardware rated for the weight of the fixture.

•

In addition to primary suspension, attach a safety cable

to the fixture housing. An appropriate attachment point

(hole) is provided in the protruding tab on the fixture

housing.

•

Disconnect the unit from power and DMX and allow the

fixture to cool before removing or installing accessories,

and before all cleaning and maintenance.

4 Source 4WRD Color Installation and User Manual

AVERTISSEMENT : Prendre connaissance des avertissements

de sécurité suivants avant toute utilisation :

•

Ne pas installer le projecteur sur ou à côté d’une surface

inflammable.

•

Ne pas utiliser ce projecteur avec un cordon

d’alimentation endommagé. Si le cordon d’alimentation

(câble) est abîmé, il doit être remplacé.

•

Installer et accrocher le projecteur uniquement par les

trous de fixation principaux de la lyre.

•

Accrocher le projecteur à une structure convenable en

utilisant seulement du matériel adapté au poids du

projecteur.

•

En plus de l'accroche principale, fixer une élingue de

sécurité (modèle ETC400SC ou autre câble/dispositif de

sécurité certifié) au corps du projecteur. Un point

d’accroche (trou) approprié est prévu dans la patte qui

ressort du boîtier du projecteur.

•

Déconnecter l’alimentation et le DMX et laisser le

projecteur refroidir avant d’enlever ou installer

l'optique découpe ou les autres adaptateurs, et avant

tout nettoyage et entretien.

WARNING: Note the following safety warnings before use:

•

The Source 4WRD Color is not user serviceable. Field

modification of the Source 4WRD Color will void your

ETC warranty.

•

Do not use the fixture below 5°C (41°F).

•

Minimum storage temperature is 5°C (41°F). When the

fixture has been stored or transported in cold

temperatures, allow it to warm to room temperature

for a minimum of 1hour before applying power.

Applying power to a cold fixture will cause damage to

the fixture and void the ETCwarranty.

•

Do not use this fixture if a glass lens is deeply scratched

or cracked. Damaged lenses must be replaced.

•

To prevent wiring damage, or abrasion, do not expose

wiring to edges of sheet metal or other sharp objects.

•

Use the fixture in dry locations only, where humidity

does not exceed 90 percent (non-condensing). These

fixtures are not intended for outdoor use.

Source 4WRD Color Installation and User Manual 5

Retrofit the Fixture

WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Installing the

Source 4WRD Color retrofit kit requires knowledge of

luminaire electrical systems. If you are not qualified, do not

attempt installation. Contact a qualified electrician.

AVERTISSEMENT : RISQUE D'INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE! Installer le nécessaire de conversion Source

4WRD Color nécessite une connaissance des systèmes

électriques de projecteurs. Si vous n’êtes pas qualifié, ne

tentez pas l’installation. Faire appel à un électricien qualifié.

Note:

THE RETROFIT KIT IS ACCEPTABLE AS A COMPONENT OF A

LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL

BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.

Retrofit kit

LEDs

RJ45 data in

and data thru

User interface and

navigation buttons

Wire the Power Connector(If Needed)

If you ordered a Source 4WRD Color retrofit without a power connector,

wire the connector in accordance with all national and local electrical

codes:

•

Brown = Live

•

White (heat shrink on blue wire) = Neutral

•

Green/Yellow = Protective earth

6 Source 4WRD Color Installation and User Manual

Remove Incandescent Lamp Housing

1. Unplug the Source Four incandescent fixture and place it on a flat,

stable surface.

2. Loosen the brass thumb screw located above the beam adjustment

knob. The lamp housing is now loose.

3. Remove the lamp housing from the fixture body.

Note:

The burner assembly is no longer needed. If you would like

ETC to recycle the burner assembly, contact ETC Technical Services

for more information. See Help from ETC Technical Services on

page2.

Install the Source 4WRD Color Retrofit

WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Install this kit

only onto luminaires that have the construction features and

dimensions shown in the images in this document and where

the input rating of the retrofit kit does not exceed the input

rating of the luminaire.

AVERTISSEMENT : RISQUE D'INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE! N’installer ce kit que sur les projecteurs qui ont

les caractéristiques de construction et les dimensions

indiquées sur les images de ce document et où la puissance

électrique nécessaire à la conversion n’excède pas la puissance

maximale du projecteur.

WARNING: Do not make or alter any open holes in an

enclosure of wiring or electrical components during kit

installation.

Altri manuali per Source 4WRD

Indice

Altri manuali ETC Apparecchio di illuminazione

ETC

ETC High End Systems SolaPix 7 Manuale utente

ETC

ETC Desire series Manuale utente

ETC

ETC Desire D22 Manuale utente

ETC

ETC Desire D40 Manuale utente

ETC

ETC Irideon FPZ Manuale utente

ETC

ETC Source Four Revolution Manuale utente

ETC

ETC Desire D22 Manuale utente

ETC

ETC ColorSource CYC v1.7 Manuale utente

ETC

ETC ColorSource Linear Manuale utente

ETC

ETC Source Four Revolution Manuale utente

ETC

ETC DataTrack Manuale tecnico

ETC

ETC ColorSource PAR Pearl Manuale utente

ETC

ETC Source Four Zoom Manuale utente

ETC

ETC HIGH END SYSTEMS SolaFrame Theatre Manuale utente

ETC

ETC HIGH END SYSTEMS SolaPix 37 Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente