ETC Mosaic 5 Manuale utente
ETC Installation Guide
Mosaic 5" and 8" Touchscreen
Corporate Headquarters nMiddleton, WI, USA |+1 608 831 4116
Global Offices nLondon, UK |Rome, IT |Holzkirchen, DE |Paris, FR |Hong Kong
Dubai, UAE |Singapore |New York, NY |Orlando, FL |Los Angeles, CA |Austin, TX
Web etcconnect.com |Support support.etcconnect.com
Contact etcconnect.com/contactETC |© 2023 Electronic Theatre Controls, Inc.
Trademark and patent info: etcconnect.com/ip |Product information and specifications
subject to change. ETCintends this document to be provided in its entirety.
7180M2161 Rev B Released 2023-09
Overview
M-TS5 M-TS8
The Mosaic Touchscreen is a
wall-mounted touchscreen
controller that is available in
5" and 8" models. The
touchscreen provides
dynamic control of your
Mosaic system using faders,
buttons, color pickers, and
more.
The graphic touchscreen display configuration is designed using Mosaic
Designer Software (v2.9 and later) and can be customized to meet your
installation needs.
Mounting
D
C
B1
B2
A1
A2
8”
Mounting
Plate
5”
Mounting
Plate
D
C
B
A
Each touchscreen ships
with a mounting plate and
region-specific hardware
for installation to a
standard US/EU/UK back
box in either portrait or
landscape orientation. A
surface-mount back box is
available separately.
Model A B C D
5" Mounting
Plate
US 1-gang
Back Box
A- 83 mm
(3.3in)
UK 1-gang
Back Box
B- 60 mm
(2.4in)
EU 1-gang
Back Box
C- 60 mm
(2.4in)
UK 2-gang
Back Box
D- 120 mm
(4.75 in)
8"Mounting
Plate
US3-gang
Back Box
A1 - 92 mm
(3.6 in)
A2 - 83 mm
(3.3 in)
EU 2-gang
Back Box
B1 - 71 mm
(2.8 in)
B2 - 60 mm
(2.4 in)
US 2-gang
Back Box
C- 46 mm
(1.8in)
UK 2-gang
Back Box
D- 120 mm
(4.75 in)
ETC Installation Guide
5" and 8" Touchscreen
Vertical mounted back box
(portrait operation)
Horizontal mounted back box
(landscape operation)
US 1-gang back box shown in both portrait and landscape orientation.
Environment
• For dry location use only, ambient temperature 0°C–50°C
(32°F–122°F)
• Humidity 10%–95% (non-condensing)
Electrical
The touchscreen is powered by Power-over-Ethernet (PoE 802.3af).
Astandard PoE switch (provided by others) not exceeding 15W may be
used to provide both power and a network connection to the touchscreen
using an Ethernet cable. All Ethernet terminations must follow IEEE 802.3
and be terminated to the T568B standard.
If a PoE switch is not available, a compliant PoE midspan injector may be
used alternatively. The touchscreen operates as a PoE Class 0 (zero)
device (0.44–12.95W) and consumes 7W maximum.
Note:
Power must not be disconnected during
bootloader/firmware updates to the unit as corruption of the data
or software may occur, perhaps even rendering the unit
inoperable.
5" and 8" Touchscreen Page 2 of 4 ETC
ETC Installation Guide
5" and 8" Touchscreen
Installation
1. The touchscreen universal mounting plate installs to a flush-mount
or surface-mount back box in either the portrait or landscape
orientation. The 5" touchscreen requires a standard 1-gang back
box and the 8"touchscreen requires a standard 2-gang back box.
Note:
All flush-mount installations require a back box with a
minimum of a 49mm hole. Use the appropriate mounting
hardware for your installation back box (UNC 6-32 screw for US
back box, M3.5 flat head screw for UK back box, or M3 hex head
screw for EU back box).
2. Connect the Ethernet cable to the RJ45 port receptacle on the rear
panel of the touchscreen.
3. Attach the touchscreen to the mounting plate.
a. Angle the touchscreen to the mounting plate at a 10 degree
clockwise angle where the keyholes on the touchscreen are
aligned to the locating lugs on the universal mounting plate.
Ethernet CAT5
Ethernet CAT5
10°
Locating
Lugs (x4)
b. Once all located lugs are seated to the touchscreen, rotate the
touchscreen 10 degrees counterclockwise, securing it in place.
5" and 8" Touchscreen Page 3 of 4 ETC
ETC Installation Guide
5" and 8" Touchscreen
Service
Lnk/Dat
Pwr/Act
10/100 TX PD
ETHERNET
10 W MAX
Reset
Button
Ethernet
MicroSD
Memory Card
Remove Touchscreen
1. To remove the touchscreen from the universal mounting plate,
gently pull the short sides of the touchscreen toward you and rotate
it 10 degrees clockwise.
2. Remove the touchscreen from the locating lugs.
3. Disconnect the Ethernet cable from the RJ45 port.
Memory Card
The touchscreen ships with a 32GB MicroSD Memory Card installed. In
the event of touchscreen hardware failure, you can simply move the
memory card into a replacement touchscreen that is running compatible
(same or later) firmware to resume operation.
Reset Button
Reset the touchscreen hardware by removing the device from the
mounting plate (see
Remove Touchscreen above
) and pressing the
recessed reset button located on the rear panel.
Note:
Do not reset the hardware during a bootloader/firmware
update as corruption of the data or software may occur, perhaps
even rendering the touchscreen inoperable.
Watchdog
An internal "watchdog" will automatically reset the touchscreen in case
of a software crash as a result of either a software defect or a random
electromagnetic event, such as a power brownout or power spike, a
nearby lightning strike, or static discharge.
5" and 8" Touchscreen Page 4 of 4 ETC
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali ETC Schermo tattile
ETC
ETC Unison Paradigm P-TS7 Manuale utente
ETC
ETC Paradigm P-LCD Series Manuale utente
ETC
ETC Unison Paradigm P-LCD-FBB Manuale utente
ETC
ETC PARADIGM Manuale utente
ETC
ETC Unison Paradigm P-TS7 Manuale utente
ETC
ETC Paradigm Portable Touchscreen Manuale utente
ETC
ETC Paradigm P-TS7-E Manuale utente
ETC
ETC Unison Paradigm P-TS7 Manuale utente
ETC
ETC Mosaic 5 Manuale utente
ETC
ETC Unison Paradigm P-TS7 Manuale utente
Manuali Schermo tattile popolari di altre marche
Elecro Engineering
Elecro Engineering Poolsmart Plus Istruzioni per l'installazione
Johnson Controls
Johnson Controls IQ4 HUB Manuale utente
Elo TouchSystems
Elo TouchSystems ET2270L Manuale utente
Elo TouchSystems
Elo TouchSystems ET1002L Manuale utente
Elo TouchSystems
Elo TouchSystems 3201L Manuale utente
Duratec
Duratec S15 Manuale utente
