ETEKCITY CLF50 Manuale utente
1
Questions or Concerns? support@etekcity.com • (855) 686-3835
LED Camping
Lantern Flashlight
Model No.: CLF50
2
Thank You!
Thank you for purchasing the CLF50 LED Camping
Lantern Flashlight. We are dedicated to providing our
customers with quality products for building on a better
living. Should you have any questions or concerns about
using your new product, feel free to reach out to our helpful
Customer Support team at support@etekcity.com. For
more contact information please refer to page 14. We hope
you enjoy your new product!
3
Table of Contents Specifications
Power Supply 3 x 1.5V AA Batteries
(Pre-installed)
Rated Power 3W
Max Brightness Lantern Mode: 300 Lumen
Flashlight Mode: 110 Lumen
Battery Life Lantern Mode: 12 Hours*
Flashlight Mode: 20 Hours*
Protection Level IP54**
Weight 10.3 oz (292 g)
Dimensions Fully Collapsed: 5.5 x 3.3 in.
(139.7 x 83.8 mm)
Fully Extended (with handle):
9.2 x 3.3 in. (233.6 x 83.8 mm)
Safety Information
Function Diagram
Set-Up
Operation
· Adjustable Handle
· Flashlight Mode
· Lantern Mode
Battery Replacement
Warranty Information
Customer Support
4
5
6
7
7
10
11
12
13
14
NOTE:
* These times are based on using the lantern with a brand new
set of alkaline batteries. Using other types of batteries that are
not alkaline may shorten the operating time of the lantern.
** The International Protection (IP) Rating is the system that
classifies the degrees of protection provided against the
intrusion of solid objects, dust, accidental contact, and water
in electrical enclosures. An IP54 rating means this lantern is
protected from limited dust ingress and water spraying from
any direction.
4
Safety Information
General Safety
• DO NOT replace batteries while hands are wet.
• DO NOT replace batteries in wet environments.
• ONLY use 1.5V AA batteries with this camping
lantern.
• DO NOT shine the light into the eyes of other
person(s). Doing so may result in serious injury.
Use & Care Guidelines
• When not in use, turn off the lantern by
completely collapsing the device. If you are using
the lantern as a flashlight, press the ‘Flashlight
Button’ to turn off the light.
• When installing or changing batteries, always
make sure to place the batteries under the
correct polarity as indicated within the battery
compartment.
• If you are using rechargeable batteries, make
sure they have the required voltage necessary to
power the lantern.
• DO NOT dispose of any part of this product in
a fire.
• Properly dispose of all parts of this product in
accordance with local environmental regulations.
DO NOT dispose of the lantern or batteries in
regular household waste.
• DO NOT submerge the lantern into water or any
other liquid.
• DO NOT attempt to open the lantern for self-
servicing, other than for changing the batteries.
Doing so may result in damage to the product,
electric shock, or injury. Doing so will also void
your warranty.
• DO NOT use replacement parts that from other
Etekcity lanterns or parts from other third-party
products.
• Use a damp or dry cloth to wipe the lantern’s
surface when cleaning.
• When not in use for an extended period of time,
remove the batteries to avoid power drainage.
IMPORTANT: Please read and comply with all of the instructions and warnings provided in this manual
before using the product. Failure to comply with the instructions and warnings provided herein may result in
inaccurate results and/or damage to the product itself.
5
Function Diagram 1. Handle
2. Handle Clips
3. Clip Holder A
4. Clip Holder B
5. Clip Holder C
6. LED Strip
7. Flashlight Button
8. Flashlight
9. Battery Compartment
1 2
3 4
9
6
7 8
5
Top View Side View
6
Set-Up
1. Remove the battery compartment lid by twisting
it counterclockwise, then lifting it up from the
lantern. [Figures 1.1 & 1.2]
2. Remove the insulation strip and replace the
battery compartment lid.
[Figure 1.3]
Figure 1.1 Figure 1.2 Figure 1.3
Before First Use
7
Figure 2.1
Flashlight Mode
Lantern Mode
Figure 2.2
Operation
Adjustable Handle
Your new lantern can be used in two different ways:
Flashlight Mode and Lantern Mode. [Figure 2.1 & 2.2]
8
Figure 2.3 Figure 2.4
The Adjustable Handle (cont.)
Adjusting from Flashlight Mode to Lantern Mode
1. Pinch the clip that is connected to Clip
Holder C, then remove the clip. [Figure 2.3]
2. Place the removed clip into Clip Holder A at
the top of the lantern. [Figure 2.4]
A
C
9
Figure 2.6Figure 2.5
Adjusting from Lantern Mode to Flashlight Mode
1. Pinch the clip that is connected to Clip
Holder A, then remove the clip.
[Figure 2.5]
2. Place the removed clip into Clip Holder C
next to the ‘Flashlight Button.’ [Figure 2.6]
A
C
10
Figure 3.1 Figure 3.3Figure 3.2
1. Adjust the lantern to Flashlight Mode. [Figure 3.1]
2. Press the ‘Flashlight Button’ on the side of the
lantern to turn on the flashlight. [Figure 3.2]
Flashlight Mode
3. Grasp the handle to hold the lantern. [Figure 3.3]
4. Press the ‘Flashlight Button’ once more to turn
off the flashlight.
Indice
