ETEKCITY EHS-18 Manuale utente
2
Table of Contents
Package Contents
Safety Information
Function Diagram
LCD Display
Setup
• Battery Installation
Operation
• Weight Measurement
• Unit Conversion
• Data Hold Function
• Tare Function
Care & Maintenance
• Replacing Batteries
Specifications
Warranty Information
3
4
5
6
7
7
8
8
8
9
9
10
10
11
11
EN Inhaltsverzeichnis
Verpackungsinhalt
Wichtige Sicherheitshinweise
Funktionsdiagramm
LCD-Anzeige
Einstellung
• Installierung der Batterien
Betrieb
• Gewichtsmessung
• Umrechnung von Einheiten
• Daten-Hold-Funktion
• Tarafunktion
Pflege und Wartung
• Auswechseln der Batterien
Technische Daten
Garantieinformationen
3
12
13
14
15
15
16
16
16
17
17
18
18
19
19
DE
3
1 x Digital Hanging Scale
2 x 3V CR2032 Batteries (Pre-Installed)
1 x Carrying Pouch
1 x User Manual
1 x Digitale Hängewaage
2 x 3 V CR2032 Batterien (vorinstalliert)
1 x Tragetasche
1 x Benutzerhandbuch
Package Contents
EN
Verpackungsinhalt
DE
Français
Español
Italiano
4
EN
ENGLISH •Digital Hanging Scale EHS-18
Safety Information
• Do not exceed the weight capacity of 50 kg
(110 lb). An overload indicator will appear on
the digital display if the limit is exceeded.
• This scale is not intended for commercial or
heavy-duty use. Household use only.
• Do not throw or strike the scale and do not
submerge the scale in water.
Follow all instructions and safety guidelines.
Read all instructions before using.
SAVE THESE
INSTRUCTIONS
5
EN
Function Diagram
A. Handle
B. LCD Display
C. ON/OFF Button
D. TARE Button
E. UNIT Button
F. Measuring Tape
G. Hook
H. Battery Compartment
I. Hook Storage
A
B
G
F
H
I
C
D
E
Front Back
6
EN
LCD Display
A. Measured weight is less than
the calibrated tare weight
B. Displayed weight is the
tared weight
C. Last measured weight
D. Weight in grams
E. Weight in ounces
F. Weight in kilograms
G. Weight in pounds
H. Maximum weight capacity
has been exceeded
(remove object from hook
immediately)
I. Battery low
Tare
Hold
H
I
AE
G
D
F
B
C
g
kg
lb
oz
7
EN
Setup
1. Open the battery cover.
2. Remove the insulation strip to activate the
batteries. [Figure 1.1]
3. When replacing the batteries, make sure to
insert them under the proper polarity.
Battery Installation
Figure 1.1
8
EN
Press UNIT repeatedly to change the unit of
measurement (g / oz / kg / lb).
Unit Conversion
1. Press ON/OFF and the screen will light up.
Wait for “ “ to appear on the screen.
[Figure 2.1]
2. Hang the object you want to measure on
the hook.
3. Lift the scale with the object and hold still
until the weight measurement stabilizes.
The display will show the weight and
“Hold”.
4. To measure another item, remove the
object and repeat steps 2 and 3.
5. Press ON/OFF to turn the scale off. The
scale will automatically turn off if the scale
is inactive for 60 seconds.
Operation
Weight Measurement
Note: To avoid result inaccuracy, keep the scale upright
when measuring. Do not touch or move the scale during
measurement. Always grasp the scale by the handle.
lb
Figure 2.1
9
EN
Once the weight has stabilized and “Hold”
appears on screen, the weight will stay on the
screen for 60 seconds, or until you measure
another object or press TARE.
Turning the data hold function on or off:
1. When the scale is on, press and hold TARE
for 3 seconds.
2. Press UNIT to alternate between turning
data hold function on or off.
Hoon - Data hold function on
HooF - Data hold function off
3. Press TARE to confirm selection.
Data Hold Function
The tare function allows users to weigh an
object inside a container by subtracting the
weight of the container from the total weight.
1. Hang the container on the weighing scale
hook and allow the weight to stabilize and
lock (the word “Hold” will appear).
2. Hold the scale stable and press TARE to
tare the current weight. The display will
show “ “.
3. Place the object you want to weigh inside
the container and the scale will calculate
the weight of the object without the weight
of the container.
Tare Function
10
EN
Care & Maintenance
• Do not use chemical detergents to clean
the scale. Use a soft, damp cloth if needed.
• If not in use for a long period of time,
remove the batteries and store the scale
in a cool, dry environment to avoid circuit
damage.
1. Locate the battery compartment on the
back of the scale and remove the battery
compartment cover.
2. Ensure the +side of the battery is facing
up and insert the batteries into the battery
slots. [Figure 3.1]
3. Replace cover.
Replacing Batteries
Figure 3.1
Altri manuali per EHS-18
2
Indice
Lingue:
Altri manuali ETEKCITY Scala
ETEKCITY
ETEKCITY EK8060 Manuale utente
ETEKCITY
ETEKCITY ESF-551 Manuale utente
ETEKCITY
ETEKCITY ESF24 Manuale utente
ETEKCITY
ETEKCITY ESB-591 Manuale utente
ETEKCITY
ETEKCITY ESF38 Manuale utente
ETEKCITY
ETEKCITY ESN00 Manuale utente
ETEKCITY
ETEKCITY EB4074S Manuale utente
ETEKCITY
ETEKCITY Luminary EKS-L221-SCA Manuale utente
ETEKCITY
ETEKCITY EK6015 Manuale utente
ETEKCITY
ETEKCITY EK3551 Manuale utente
ETEKCITY
ETEKCITY EK7017 Manuale utente
ETEKCITY
ETEKCITY EK6314-T Manuale utente
ETEKCITY
ETEKCITY EHS-18 Manuale utente
ETEKCITY
ETEKCITY FIT 8S Manuale utente
ETEKCITY
ETEKCITY FIT 8S Manuale utente
ETEKCITY
ETEKCITY EK6015 Manuale utente
ETEKCITY
ETEKCITY EB4074S Manuale utente
ETEKCITY
ETEKCITY ESF93 Manuale utente
ETEKCITY
ETEKCITY ESF00+ Manuale utente
ETEKCITY
ETEKCITY EK9000 Manuale utente
