ETI ADH NETCOM AC NEMA Manuale utente

South Bend, Indiana USA | networketi.com ADH INSTRUCTION MANUAL | PART NO.24100 REV B

NETCOM

®MODEL ADH

AUTOMATIC AIR DEHYDRATOR WITH ETHERNET

ADH® NETCOM™ AC NEMA AUTOMATIC AIR

DEHYDRATOR POWER FILTER MODULE

REPLACEMENT PROCEDURE

Replacement Kit Part Number 24087

Document Part Number 24100

SAFETY INFORMATION AND WARNINGS

Abnormal Odor or Smoke

In the event of smoke or a burning or

abnormal odor, immediately interrupt

power to the ADH NETCOM with the

POWER switch at the rear of the unit,

unplug the unit, or turn off the circuit

breaker controlling the outlet. Note

that only the AC model of the ADH

NETCOM has an ON / OFF switch.

Lethal Voltages Present

Lethal voltages are present inside the

ADH NETCOM. Service should be

performed by qualified personnel

only. There are no user serviceable

components inside the chassis.

Pneumatics

Each of the air pumps inside the ADH

NETCOM automatic air dehydrator is

capable of generating as much as 24

psig (1,655mbar). Other attached dry

air sources may be capable of

generating even higher pressures.

Proper safety practice requires

treating all pneumatic components

with care. Always vent the system to

atmospheric pressure before servicing

pneumatic components.

Rack Mounting

Before and after rack mounting the

ADH NETCOM, ensure that the rack

is stable. Mounting of the ADH

NETCOM into a rack should be such

that a hazardous condition is not

created due to uneven mechanical

loading. Verify that adequate air

flow and power source capacity is

available to the unit. Ensure that the

ADH NETCOM maximum operating

temperature of 130°F (55°C) will not

be compromised by other

components in the rack. Ensure

reliable earthing of the ADH

NETCOM.

South Bend, Indiana USA | networketi.com ADH INSTRUCTION MANUAL | PART NO.24100 REV B

ADH NETCOM AC NEMA POWER

FILTER MODULE REPLACEMENT

PROCEDURE

This procedure addresses the removal and

replacement of the Power Filter Module in

an ADH NETCOM AC NEMA Automatic Air

Dehydrator. It is recommended to read

the entire procedure prior to beginning

work.

INVENTORY LIST

Identify the following items in this kit prior

to beginning work.

TOOLS REQUIRED

The following tools are needed to perform

this procedure:

•Small flat blade screwdriver

•Nut driver

•Tubing wrench or vacuum tube pliers

•11/32” open end wrench

•Philips screwdriver

•Needle nose pliers

•Long screwdriver

Item

Number

Part

Number

Item

Quantity

Item

Description

1 23563 1 Power Filter Module

22 24100 1 Instruction Manual (this document)

South Bend, Indiana USA | networketi.com ADH INSTRUCTION MANUAL | PART NO.24100 REV B

POWER FILTER MODULE

REMOVAL AND REPLACEMENT

To replace the Power Filter Module (23563)

in an ADH NETCOM AC NEMA Automatic

Air Dehydrator, perform the steps below.

1. Shut off machine power by

unplugging the unit.

2. Open the two front door latches,

loosen the two captive screws in the

corners of the housing opposite the

hinges, then open the NEMA box.

Place an object underneath the door

once open to help support it during

this procedure.

3. Remove the orange Ethernet cable on

the left by disconnecting both ends,

then removing it. Set aside for re-use.

Remove the power cable connector

on the right by loosening the captive

screw on each end of the green

connector, then unplugging the

connector. Disconnect the ground

wire by loosening the ground wire

retaining screw, then carefully

removing the ground wire. Refer to

Figure 1.

Figure 1. DISCONNECTING THE ETHERNET

CABLE,

THE POWER CABLE CONNECTOR, AND

THE GROUND WIRE.

Disconnect

both ends,

then remove

orange

ethernet cable.

Loosen both captive screws,

then disconnect connector.

Loosen

screw,

then

remove

ground

wire.

4. Remove and retain the four mounting

screws from the four corners of the

protective front cover, then slowly lift

the front cover, carefully flip it over,

then set it down, upside down, to rest

on the inside of the enclosure door.

Be careful as there are still many wires

connected between the enclosure

and the front cover and there isn’t a

lot of slack. Note that the two upper

front cover mounting screws are

located in plain sight in the top

corners of the front cover, while the

two lower front cover corner

mounting screws are located down in

the front “well” of the unit. Use a

long-handled screwdriver to remove

them.

South Bend, Indiana USA | networketi.com ADH INSTRUCTION MANUAL | PART NO.24100 REV B

5. Note how the five electrical leads are

connected to the existing Power Filter

Module, then use a needle nose pliers

to carefully disconnect the leads from

the module. The two leads on the

Load side connect to the green power

connector. The three leads on the

Line side connect to the power supply.

Of the two connector leads, the black

lead is the line and the white lead is

neutral. Of the three output leads, the

black lead is the line, the white lead is

neutral, and the green/yellow lead is

ground. All of these leads will connect

to the new module the same way.

Figure 2. THE POWER FILTER MODULE.

The two leads on the

Load side connect to

the green power

connector.

The three leads on the

Line side connect to

the power supply.

6. Using the nut driver, remove and

retain the nuts and lock washers

securing the existing module to the

chassis. Once all five electrical leads

have been disconnected and the

mounting hardware has been

removed, remove the existing Power

Filter Module from the unit.

7. Position the new Power Filter Module

over the Pem

studs on which the

original module was installed. Using

the nuts and lock washers retained in

step 6, install the new Power Filter

Module and torque to 10 in/lb.

Connect the electrical leads in the

corresponding locations on the new

Power Filter Module from which they

were removed on the old module.

Refer to the following tables. Make

sure all leads are secure.

Load Side Connections

Black Line

NeWhite

Line Side Connections

Black Line

White Ne

Green/Yellow

12. Reinstall the front cover removed in

step 4. If it was placed upside down

on the lid of the unit during this

procedure, carefully turn the cover

back over and work it back into

position, past the wires and other

components in the enclosure.

Reinstall the four corner screws

securing the front cover to the

chassis.

13. Reconnect the ground wire by

inserting it behind the retaining

screw from which it was removed,

then tighten the ground wire

retaining screw. Reconnect the green

power connector by holding it in

place then tightening the two captive

screws removed in step 3. Reconnect

both ends of the orange ethernet

cable removed in step 3. It does not

matter which end of the ethernet

cable goes into which receptacle.

South Bend, Indiana USA | networketi.com ADH INSTRUCTION MANUAL | PART NO.24100 REV B

With the ground wire, power

connector and Ethernet cable

reconnected, close the lid of

the NEMA enclosure and

secure the two latches opposite

the hinges. Secure the lid in

place by reinstalling the two

captive screws in the two outer

corners of the lid.

Restore machine power by

plugging the unit back in.

14.

15.

QUESTIONS AND COMMENTS

For technical help, questions, or

comments concerning this or any

ETI, Inc., product, contact the

Customer Service Department

between 8:00 a.m. and 5:00 p.m. EST.

DISCLAIMER

ETI, Inc. makes no representations or

warranties, either expressed or implied

with respect to the contents of this

publication or the products that it

describes, and specifically disclaims any

implied warranties of merchantability or

fitness for any particular purpose. ETI,

Inc. reserves the right to revise this

publication and to make changes and

improvements to the products

described in this publication without the

obligation of ETI, Inc. to notify any

person or organization of such

revisions, changes or improvements.

No part of this manual may be

reproduced or translated in any form or

by any means, electronic or mechanical

including photocopying and recording,

for any purpose without the express

written consent of ETI, Inc.

The ETI logo, We Manage Heat, and

ADH are registered trademarks of ETI,

Inc. NETCOM is a trademark of ETI, Inc.

reserved.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ETI Asciugatrice

ETI

ETI NETCOM ADH Manuale utente

Manuali Asciugatrice popolari di altre marche

Bosch

Bosch WTA79200GB Manuale utente

Amana

Amana W10233410A Manuale utente

Miele

Miele TWH 780 WP Manuale utente

Asko

Asko T760 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manuale utente

Bosch

Bosch Logixx 10 WTB76556GB Scheda tecnica

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manuale di istruzioni

Electrolux

Electrolux EW2H328R2 Manuale utente

Beko

Beko DS8433RX1M Manuale utente

Dawlance

Dawlance Spinner DS 6000 C Manuale utente

Electrolux

Electrolux TP5080TW Manuale utente

AEG

AEG TR838P4OB Manuale utente

Indesit

Indesit IDV 75 Manuale utente

Infiniton

Infiniton SD-DG85C Manuale utente

BOMANN

BOMANN WT 5019 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manuale utente

Asko

Asko T793C Manuale utente

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manuale utente