Eurotherm TE200A Manuale utente

iTE200A User manual HA175773ENG Iss 1 10/97

Two-phase control of three-phase loads

TE200A

Power controllers

Two-phase control

of three-phase loads

User manual

©Copyright Eurotherm Automation 1997

(electronic or mechanical, including photocopying or recording) without written authorisation

from EUROTHERM AUTOMATION is strictly prohibited.

EUROTHERM AUTOMATION has made every effort to ensure that the specification given in

this manual is as accurate and up to the minute as possible. However, in order to maintain our

‘leading edge’, it may be necessary to make certain changes or omissions to our specification. We

cannot be held responsible for any damage to persons or property or for any financial loss or costs

arising from this.

TE200A User manualii

Two-phase control of three-phase loads

TE200A

USER MANUAL

CONTENTS Page

EUROPEAN DIRECTIVES . . . . . . . . . . . . . . . . . . . . . . . . . .iv

CE MARKING AND SAFETY . . . . . . . . . . . . . . . . . . . . . . .iv

ELECTROMAGNETIC COMPATIBILITY (EMC) . . . . . . .iv

DECLARATION OF CE CONFORMITY . . . . . . . . . . . . . . .v

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi

CHAPTER 1 IDENTIFYING THE CONTROLLERS . . . . . . . . . . . . . . . .1-2

GENERAL INTRODUCTION TO THE TE200A SERIES .1-2

TECHNICAL SPECIFICATION . . . . . . . . . . . . . . . . . . . . .1-5

PRODUCT CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7

EXAMPLE OF PRODUCT CODE . . . . . . . . . . . . . . . . . . .1-8

SERIAL NUMBER LABELS . . . . . . . . . . . . . . . . . . . . . . .1-8

CHAPTER 2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

INSTALLATION - SAFETY . . . . . . . . . . . . . . . . . . . . . . . .2-2

DIMENSIONAL DETAILS . . . . . . . . . . . . . . . . . . . . . . . . .2-3

MOUNTING DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5

CHAPTER 3 WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

WIRING - SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

POWER WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

USER TERMINAL BLOCKS . . . . . . . . . . . . . . . . . . . . . . .3-5

iiiTE200A User manual

Two-phase control of three-phase loads

Page

CHAPTER 4 CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

CONFIGURATION - SAFETY . . . . . . . . . . . . . . . . . . . . . .4-2

DRIVER BOARD CONFIGURATION . . . . . . . . . . . . . . . .4-3

CHAPTER 5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

THYRISTOR FIRING MODES . . . . . . . . . . . . . . . . . . . . . .5-2

CONTROL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

CHAPTER 6 COMMISSIONING PROCEDURE . . . . . . . . . . . . . . . . . . .6-2

COMMISSIONING PROCEDURE - SAFETY . . . . . . . . . .6-2

CHECKING THE CHARACTERISTICS . . . . . . . . . . . . . .6-3

POWERING UP THE CONTROLLER . . . . . . . . . . . . . . . .6-4

CHAPTER 7 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2

FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2

SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5

TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5

TE200A User manualiv

Two-phase control of three-phase loads

EUROPEAN DIRECTIVES

CE MARKING AND SAFETY

TE200A products carry the CE mark in compliance with the essential requirements of the

European Low Voltage Directive 73/23/EEC of 19/2/73 (amended by the Directive

93/68/EEC of 22/7/93).

For safety reasons, TE200Aproducts installed and used in compliance with this User Manual

meet the essential requirements of the European Low Voltage Directive.

ELECTROMAGNETIC COMPATIBILITY (EMC)

For an industrial environment only, must not be used in domestic environments.

Eurotherm certifies that TE200Aproducts, installed and used in compliance with these

Instructions, meet the following EMC standards and enable the system which incorporates

them to comply with the EMC Directive, as far as the TE200Aproducts are concerned.

EMC test standards

Immunity Generic standard : EN 50082-2

Test standards : EN 61000-4-2, EN 61000-4-4, ENV 50140, ENV 50141

ENV 50204

Emission Generic standard : EN 50081-2

Test standard : EN 55011 ClassA

Product standard : IEC 1800-3 (second environment)

Internal EMC filters

EMC filters are incorporated in the TE200Ato reduce conducted emission in accordance with

the corresponding test standard.

EMC Guide

In order to help you reduce the effects of electromagnetic interference depending on the prod-

uct installation, Eurotherm can supply you with the 'Electromagnetic Compatibility'

Installation Guide (ref: HA 025464).

This guide lists the rules generally applicable for EMC.

vTE200A User manual

Two-phase control of three-phase loads

DECLARATION OF CE CONFORMITY

A declaration of CE conformity is available on request.

Validation by Competent Body

Eurotherm has validated the compliance of TE200Aproducts with the European Low Voltage

Directive and with EMC standards through product design and laboratory testing.

The tests carried out on TE200Aproducts are listed in a Technical Construction File validated

by the LCIE (Central Laboratory for the Electrical Industries), a Recognised Competent Body.

Further information

For any further information, or if in doubt, please contact Eurotherm Controls where qualified

staff are available to advise or assist you with the commissioning of your installation.

TE200A User manualvi

Two-phase control of three-phase loads

PRECAUTIONS

Safety symbols

Important safety precautions and special information are indicated in the text of the manual by

two symbols:

This symbol means that failure to take note of the information given in this manual

may have serious consequences for the safety of personnel and may even result in

electrocution.

This symbol means that failure to take note of the information may

• have serious consequences for the installation or

• lead to the incorrect operation of the power unit.

These symbols must be observed for particular points.

However the whole of the manual remains applicable.

Personnel

The installation, configuration, commissioning and maintenance of the power unit should

only be carried out by personnel qualified and trained to work with low voltage electrical

equipment in an industrial environment.

Independent alarm

Given the value of the equipment controlled by TE200Aproducts it is the responsibility of the

user, and it is highly recommended, that an independent safety device (alarm) should be

installed. This alarm must be tested regularly.

Eurotherm can supply suitable equipment.

DANGER

WARNING

1-1TE200A User manual

Two-phase control of three-phase loads IDENTIFYING THE CONTROLLERS

Chapter 1

IDENTIFYING THE TE200A POWER CONTROLLERS

Page

GENERAL INTRODUCTION TO THE TE200A SERIES . . . . . . .1-2

TECHNICAL SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

PRODUCT CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7

EXAMPLE OF PRODUCT CODE . . . . . . . . . . . . . . . . . . . . . . . . .1-8

SERIAL NUMBER LABELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8

TE200A User manual1-2

Two-phase control of three-phase loadsIDENTIFYING THE CONTROLLERS

Chapter 1 IDENTIFYING THE CONTROLLERS

GENERAL INTRODUCTION TO THE TE200A SERIES

The TE200Aseries of controllers are thyristor units designed to control the electrical power in

industrial three-phase loads.

ATE200Aseries controller is made up of two channels, each comprising a pair of thyristors

connected in anti-parallel, and a direct (unswitched) channel.

The TE200Aseries is designed to control three-phase resistive loads:

• elements with a low temperature coefficient

• short-wave infrared elements (except for the 63A model).

Three-phase loads can be connected:

• in star without neutral

• in closed delta

The wiring of the controller is independent of the supply phase rotation.

The nominal line-to-line voltage ranges¡ from 200Vac to 500Vac.

The nominal currents, defined at an ambient temperature of 45°C, of TE200Aseries

controllers are between 16A and 63A, per phase.

Figure 1-1 Current derating per phase as a function of ambient temperature

(dotted line: current limited by recommended fuse)

20 353025 40 45 50 60

Ieff(A)

Operating temperature (°C)

IN= 63A (fan-cooled)

IN= 25A

IN= 16A

IN= 50A

IN= 40A

1-3TE200A User manual

Two-phase control of three-phase loads IDENTIFYING THE CONTROLLERS

Figure 1-2 Overview of the TE200A series controller (non fan-cooled unit)

EUROTHERM

TE200A

(L1) S

(L2) T

(L3)

(T1) V

(T2) W

(T3)

40A/400V

Control signal connector Load terminal block

LED firing indicator

Supply terminal block Heatsink

Auxiliary power

supply option

Upper protection cover

TE200A User manual1-4

Two-phase control of three-phase loadsIDENTIFYING THE CONTROLLERS

The unit is controlled by analogue signals.

The analogue input signals have two voltage ranges: 0 to 5V or 0 to 10V, and one current

range: 4 to 20mA.

Local control is possible via a potentiometer (10kΩ).

The +5V user-voltage output is provided for this purpose.

The electronics of TE200Acontrollers are self-supplied from the power voltage and do not

require external connections (unless specified otherwise).

The control function for TE200Aincludes line voltage squared (V2) compensation for line

variations in the range ±10% of the nominal voltage of the controller; stability is better than

±2%.

TE200A series controllers have two thyristor firing modes:

• Burst-firing - the modulation cycle is from 30 cycles at 50% power (15 cycles ON,

15 cycles OFF) to a modulation time of approx 6 seconds at very low and very high power

demands.

• Single-cycle (one cycle of firing and one cycle of non-firing at 50% power).

ATE200Acontroller is equipped with:

• A‘driver board’which implements the control function and EMC filtering, and provides

power for the electronics. This board is also responsible for the input signal and operating

mode configurations.

• A ‘firing board’which triggers thyristor firing.

The filter which provides immunity against electromagnetic interference is located between

the power phases.

The user terminal block below the controller is used for the input signal connection without

needing access to the inside of the controller.

A green LED, labelled ‘ON’, indicates thyristor firing and is located on the front facia.

TE200A power controllers are designed to be bulkhead or DIN rail mounted.

The 63A rated unit must be permanently fan-cooled.

The fan power supply is 115Vac or 230Vac (to be specified when ordering the controller).

Indice

Altri manuali Eurotherm Controllori

Eurotherm

Eurotherm SSD Drives 635 Manuale utente

Eurotherm

Eurotherm 2100 Manuale utente

Eurotherm

Eurotherm 902 Series Manuale utente

Eurotherm

Eurotherm EPower Manuale utente

Eurotherm

Eurotherm TE300 Series Manuale utente

Eurotherm

Eurotherm Invensys 3216 Manuale utente

Eurotherm

Eurotherm 7000 Series Manuale utente

Eurotherm

Eurotherm T940X Manuale operativo

Eurotherm

Eurotherm 3508 Manuale utente

Eurotherm

Eurotherm 2132 Manuale utente

Eurotherm

Eurotherm Invensys Mini8 Manuale di installazione e funzionamento

Eurotherm

Eurotherm 3500 series Manuale utente

Eurotherm

Eurotherm 690+ Series Manuale utente

Eurotherm

Eurotherm Invensys 3216 Manuale utente

Eurotherm

Eurotherm EFit Manuale utente

Eurotherm

Eurotherm Nanodac Manuale utente

Eurotherm

Eurotherm 7000 Series Manuale utente

Eurotherm

Eurotherm 2704 Manuale utente

Eurotherm

Eurotherm Invensys 2408 Manuale utente

Eurotherm

Eurotherm 7000 Series Manuale utente

Eurotherm

Eurotherm P304c Manuale utente

Eurotherm

Eurotherm 2416 Manuale del proprietario

Eurotherm

Eurotherm 808 Manuale utente

Eurotherm

Eurotherm 2604 Manuale del proprietario

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente