Eurotronic 700087 Istruzioni operative originali
www.eurotronic.org
Made in Germany
Installation & Operation Guide
Temperature&Humidity Sensor Z-Wave Plus
EN
1 Included in delivery 3
2 Safety Instructions 4
3 Intended Use 5
4 Product description 5
5 Operating the device 6
5.1 Button 6
5.2 LEDs 6
6 Network behavior 7
7 Commissioning 8
7.1 Recommended mounting locations 8
7.2 Mounting 8
7.3 Inserting batteries 9
7.4 Add to a Z-Wave network (Inclusion) 10
7.5 Remove from a Z-Wave network (Exclusion) 10
7.6 Factory reset 10
8 Z-Wave 11
Content
9 Association 12
10 Battery 12
11 Conguration 12
12 Multilevel Sensor 13
13 Wake Up 13
14 Troubleshooting 14
15 Cleaning 14
16 Technical specications 14
17 Disposal 15
18 Warranty 15
19 Contact information 15
– 3 –
1 x Temperature & Humidity Sensor Z-Wave Plus
2 x Sticky tape
2 x AAA Batteries
1 x Quick Start Manual
1. Included in delivery
Temperature & Humidity Sensor
Z-Wave Plus
2x AAA Batteries
AAA
AAA
2x Sticky tape Quick Start Manual
NOTE! Please check the scope of delivery for completeness and intactness.
NOTE! The following figures are for illustration purposes only and may differ from the actual product.
– 4 –
Avoid potential dangers by reading the following safety instructions carefully.
SAFETY INSTRUCTIONS
- Temperature & Humidity Sensor Z-Wave Plus is designed for use in buildings.
- Operate Temperature & Humidity Sensor Z-Wave Plus only as described in the user manual.
- Temperature & Humidity Sensor Z-Wave Plus should only be put to use in a dry and dust-free place, away
from direct sunlight.
- Do not keep using the device when there is obvious damage.
- Temperature & Humidity Sensor Z-Wave Plus may not be rebuilt, modified or opened.
IMPORTANT!
Do not open the device; it does not contain any parts which can be serviced by the user. In the event of
any faults, send the device to the Service Department.
Never attempt to recharge non-rechargeable batteries and do not short circuit or open them. This could
result in the risk of overheating, fire or bursting. Never throw batteries in a fire or water. The batteries
could explode.
Leaking batteries could damage the device. Be particularly careful when handling damaged or leaking
batteries and wear protective gloves.
Switch the device off and remove the batteries if the device will not be used for a longer period.
WARNING!
Risk of fatal injury and accidents to infants and children! The packaging material represents a risk of suff
ocation. Never leave children unattended when the packaging material is nearby.
Children often underestimate the risks involved. Always keep children away from the packaging material.
The device is not a toy.
2. Safety Instructions
– 5 –
The Temperature&Humidity Sensor Z-Wave Plus is a temperature and humidity sensor for living and working
rooms that is compatible with the Z-Wave wireless standard.
The new Z-Wave sensor in a particularly small design housing provides information on room temperature
and humidity in rooms. It can thus be used perfectly as an external temperature and humidity sensor for cli-
mate and heating control. All supported gateways can use the sensor as a data source for graphical display
of temperature and humidity changes or for evaluation of the dew point (as a mold detector in apartments).
• Extra small design housing
• Use of high-precision, Swiss sensor technology
• Multicolor LED
• Returns the measured temperature (°C) and humidity (%) as well as the dew point (°C)
• Supports Z-Wave Plus S2 security (encryption)
• Battery operation with 2x AAA batteries, Micro (LR03)
4. Product description
The product is suitable for the measurement of temperature and humidity changes and can be used for the
evaluation of the dew point (as a mold detector in apartments).
For reasons of safety and approval (CE), you must not modify and/or alter the product. If you use the prod-
uct for purposes other than those described, the product may be damaged. In addition, improper use may
result in hazards such as short circuits, fire, electric shock, etc.
Read the operating instructions carefully and keep them in a safe place. Only pass the product on to third
parties together with the operating instructions.
3. Intended use
– 6 –
5. Operating the device
5.1 Button
Button Interaction Result / Behavior
Network Press once Temperature &Humidity Sensor Z-Wave Plus will send a Wake Up Notification to
the Z-Wave Controller.
Network press three times within
1 second
Temperature &Humidity Sensor Z-Wave Plus will react to inclusion or exclusion
commands.
Network hold for 10 seconds Factory resets the Temperature & Humidity Sensor Z-Wave Plus.
5.2 LEDs
Color State Meaning
red lights constantly for 5 seconds A task has failed.
green blinking Device is ready to be included or excluded.
green lights constantly for 5 seconds A task was completed successfully.
2x red 3x
green
blinking pattern Temperature &Humidity Sensor Z-Wave Plus is reset to factory
default settings.
3x red blinking Batterie insufficient.
LED-Anzeige
– 7 –
On factory default the device does not belong
to any Z-Wave network Temperature & Humidity
Sensor Z-Wave Plus needs to be added to an
existing wireless network to communicate with
the devices of this network. This process is called
Inclusion.
Temperature & Humidity Sensor Z-Wave Plus can
also be removed from a network. This process
is called Exclusion. Both processes are initiated
by the primary controller of the Z-Wave network.
This controller is turned into exclusion respective
inclusion mode. Please consult the manual of your
Z-Wave Controller how to activate Inclusion or
Exclusion mode.
If Temperature & Humidity Sensor Z-Wave Plus
has been added to a network, it has to be re-
moved prior to be added to another wireless
network.
Interoperability
This product can be operated in any Z-Wave
network with other Z-Wave certified devices from
other manufacturers. All non-battery operated
nodes within the network will act as repeaters
regardless of vendor to increase reliability of the
network.
Security
Temperature&Humidity Sensor Z-Wave Plus sup-
ports secure communication. Temperature&Hu-
midity Sensor Z-Wave Plus will communicate with
other devices secure as long as this device pro-
vides the same or a higher level of security. Other-
wise Temperature&Humidity Sensor Z-Wave Plus
will automatically turn into a lower level of security.
A Security Enabled Z-Wave Controller must be
used to fully utilize the Temperature & Humidity
Sensor Z-Wave Plus.
Communication to a Sleeping device (Wakeup)
This device is battery operated and turned into
deep sleep state most of the time to save battery
life time. Communication with the device is lim-
ited. In order to communicate with the device, a
static controller is needed in the network. This
controller will maintain a mailbox for the battery
operated devices and store commands that can
not be received during deep sleep state. Without
such a controller, communication may become
impossible and / or the battery life time is signifi-
cantly decreased.
This device will wakeup regularly and announce
the wakeup state by sending out a so called
Wakeup Notification. The controller can then
empty the mailbox. Therefore, the device needs
to be configured with the desired wakeup interval
and the node ID of the controller. If the device
was included by a static controller this controller
will usually perform all necessary configurations.
Wakeup
The wakeup interval is a tradeoff between maxi-
mal battery life time and the desired responses of
the device. To wakeup the device please perform
the following action: A single click on the network
button will wakeup the device.
The wakeup interval can be configured in 2
minute steps with a minimum wakeup interval of
10 minutes and a maximum wake up interval of 24
hours. The default setting is 60 minutes.
6. Network behavior
– 8 –
7. Commissioning
1. Open the device.
2. Fasten the lower part to the wall with the adhesive tape. Alternatively, you can use 2 screws (not part of
delivery scope) to fasten the sensor at the wall.
7.1 Recommended mounting locations
7.2 Mounting
Attach your Temperature & Humidity Sensor Z-Wave Plus to the wall.
The optimum installation height is 1.50 m above the ground.
Do not install the Temperature & Humidity Sensor Z-Wave Plus:
• on exterior walls.
• near windows and doors.
• radiators or in the vicinity of other heat sources.
• where it is exposed to direct sunlight.
– 9 –
1. Open the device.
AAA
AAA
3. Close the device again.
2. Insert the batteries. Pay attention to the correct polarity!
7.3 Inserting batteries
– 10 –
Start inclusion mode of your primary Z-Wave Controller.
Press the network button three times within 1 second.
While the inclusion is active, the LED is blinking green. If the inclusion was successful the green LED will
light up for 5 seconds. Otherwise the red led will light up for 5 seconds to indicate failure.
Start Exclusion mode of your primary Z-Wave Controller.
Press the network button three times within 1 second.
While the inclusion is active, the LED is blinking green. If the inclusion was successful the green LED will light
up for 5 seconds. Otherwise the red led will light up for 5 seconds to indicate failure.
Press and hold the network button for at least 10 seconds. The Temperature&Humidity Sensor Z-Wave Plus
will indicate the reset blinking pattern once the reset is completed.
Please use this procedure only when the network primary controller is missing or otherwise inoperable.
7.4 Add Temperature & Humidity Sensor Z-Wave Plus to a Z-Wave network
(Inclusion)
7.5 Remove Temperature&Humidity Sensor Z-Wave Plus from a Z-Wave network
(Exclusion)
7.6 Factory reset
Questo manuale è adatto per i seguenti modelli
1
Indice
