eutonomy euFIX D212 DIN Manuale utente
30-09-2020 13:58
Pagina 1 van 3http://manuals-backend.z-wave.info/make.php?lang=en&sku=EUT_EUFIXD212&cert=
Eutonomy
Eutonomy - euFIX D212 DIN adapter
(with button)
SKU: EUT_EUFIXD212
Quickstart
This is a Z-Wave Device for . To run this device please connect it to your mains power supply.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may vio
distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in t
equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or ba
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and
every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not
in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave
device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this
device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of
security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The euFIX adapters bring more professionalism to your Smart Home.
By using this professional solution you are able to mount the FIBARO moduls at DIN rail TH35 and hide them cleverly
have the choice between two versions: with or without button.
The Eutonomy euFIX D212 is suitable for the FIBARO Dimmer 2 (FIBEFGD-212) and has two buttons.
Features:
Suitable for FIBARO FGD-212
30-09-2020 13:58
Pagina 2 van 3http://manuals-backend.z-wave.info/make.php?lang=en&sku=EUT_EUFIXD212&cert=
Version with button
Power supply: 230V, 50/60Hz
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset
by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform th
the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may
assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing w
devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the p
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a specia
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing
Technical Data
Dimensions 0.0348000x0.0647000x0.0873000 mm
Weight 54 gr
EAN 5906874103005
Frequency XXfrequency
Maximum transmission power XXantenna
Explanation of Z-Wave specific terms
Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remo
controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and eve
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one prima
Inclusion — is the process of adding new Z-Wave devices into a network.
30-09-2020 13:58
Pagina 3 van 3http://manuals-backend.z-wave.info/make.php?lang=en&sku=EUT_EUFIXD212&cert=
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to co
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilitie
(c) 2020 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwave.eu. The te
Europe GmbH. The product content is maintained by Z-Wave Alliance , Certification Team, [email protected]. Last upd
Questo manuale è adatto per i seguenti modelli
1
Indice
