EVA EVAstream Manuale utente

EVAstream

Electrical connections - PCB Setting

April 2023 - V 1.0

EVAstream Electrical connections - PCB Settings 3

1 About this manual

1.1 Language

This manual is meant for the qualified electrician who performs the electrical connection of the

product. Read and understand this manual before connecting and using this product. This manual is

originally written in English. All other language versions are translations of the original manual.

1.2 Other relevant documents

1.3 Used symbols

This manual contains safety instructions. Ignoring these instructions may lead to injury or damage

to the appliance. Each safety instruction is indicated with a signal word. The signal word corresponds

with the level of risk of the described hazardous situation.

This symbol indicates a hazardous situation which, if not avoided, will result in

death or serious injury.

This symbol indicates a hazardous situation which, if not avoided, could result

in death or serious injury.

This symbol indicates a hazardous situation which, if not avoided, could result

in minor or moderate injury.

Indicates a situation that, if not avoided, could result in damage to the product

or to the environment.

Document

EVAstream: Mounting - Installation

EVAstream: User manual

EVA LED underwater light

www.evaoptic.com/downloads/

6CAUTION

6DANGER

6WARNING

NOTICE

1 About this manual 3

1.1 Language 3

1.2 Other relevant documents 3

1.3 Used symbols 3

2 Safety 4

2.1 Safety warnings and regulations 4

2.2 General safety instructions 4

3 Product 5

3.1 Intended use and reasonably foreseeable unintended use 5

3.2 Description 5

3.3 Connections 6

3.4 General specifications 6

3.5 Electrical specifications 7

4 Electrical installation 8

4.1 Connect EVAstream turbine to Motor Control Unit 8

4.2 Connect EVA Piezo to Motor Control Unit 10

4.3 Finishing the installation of the Motor Control Unit 12

5 PCB settings - general information 13

5.1 Preparation 13

5.2 EVAstream LEDs 13

6 Controlling with EVA Experience web app 14

6.1 Technical tablet requirements 14

6.2 Network connection 14

6.3 Setting the PCB and WIFI 15

6.4 New network configuration (AP mode) 17

6.5 Home network configuration 20

6.6 Setting for first use 23

6.7 Update Firmware 25

7 Controlling with EVA Piezo (without EVA Experience web app) 26

8 Disposal 27

8.1 Decommissioning 27

8.2 Disposal 27

Attachments - Overview of the EVAstream Control Print 28

Table of contents

EVAstream Electrical connections - PCB Settings EVAstream Electrical connections - PCB Settingswww.evaoptic.com4 5

3 Product

3.1 Intended use and reasonably foreseeable unintended use

The EVAstream is intended to be used as a counter-current swimming machine. The PIEZO control

panels are intended to be used to control the EVAstream.

3.2 Description

The EVAstream is a counter-current machine. The machine can be equipped with several control

panels and EVA RGBW underwater lighting. The machine is controlled by the motor control unit (MCU).

Risk of product damage. Prolonged disturbance of frequency may permanently damage

the equipment.

lNever place multiple cables in one conduit.

lNever place the motor control unit near a frequency controller.

lFor safety reasons, it is not allowed to mount lights other than EVA Optic to the EVAstream

motor control unit.

230 VAC;

16 A

NOTICE

Overview of an EVAstream configuration

Electrical shock hazard. Fatal injury will occur. Switch off all electricity near the pool before

installation or service.

Electrical shock hazard. Risk of electric shock and injury. The product must be installed by a certified

electrician. Incorrect installation will cause electrical hazards.

Electrical shock hazard. Risk of electric shock due to incorrect mounting.

lMake sure you read the enclosed documents carefully.

lNever connect the product to the main power before connecting all loose wires properly.

lAlways disconnect the product from the main power before servicing.

Electrical shock hazard. Risk of electric shock due to leakage of current.

lMake sure to install the turbine with a PE-grounding.

Risk of product damage. Prolonged disturbance of frequency may permanently damage

the equipment.

lNever place multiple cables in one conduit.

lNever place the motor control unit near a frequency controller.

6DANGER

6WARNING

NOTICE

2 Safety

2.1 Safety warnings and regulations

2.2 General safety instructions

Follow the NEN1010 guidelines. Follow the specific installation requirements of IEC 60364-7-702: 2010

(Electric low-voltage installations - Part 7-702: Requirements for special installations, spaces, and

areas – Swimming pools and fountains). Install the controller in or outside of zone 2 (NOT in zones 0

or 1) according to IEC 60364-7-702: 2010. The power supply must be equipped with an earth leakage

circuit breaker (ELCB) with a nominal differential current ≤30mA.

The EVAstream was developed as a counter-current swimming machine for use in a swimming pool.

Use for any other purpose is not permitted. Requests for exceptions to this should be submitted

to the manufacturer for technical analysis. Only after written approval by EVA Tech B.V. may the

EVAstream be applied in any other way than as prescribed in this document.

The general terms and conditions of EVA Tech B.V. apply to all our offers and agreements. EVA Tech

B.V. expressly rejects the applicability of the general (purchasing) conditions of counterparties. The

warranty provisions of the EVAstream and the general terms and conditions of EVA Tech B.V. can be

found at www.evastream.nl

EVAstream Electrical connections - PCB Settings EVAstream Electrical connections - PCB Settingswww.evaoptic.com6 7

3.3 Connections

3.4 General speciﬁcations

L PEN

Connections in the motor control unit:

1. Control print (32 pins)

2. Power connection

3. EVAstream turbine connection

EVAstream

EVA Piezo

DMX

Power input 230 VAC; 10A

Cable motor 5 m, 16 mm2

Extend with max. 20 m using 25 mm2 cable

(Flexible cable of fine copper wire strands)

Cable 10m 7-wired aqua cable

Optional: 30m 7-wired aqua cable

Cable 2 wires > 0.22 mm2 + shield 110 Ohm

3.5 Electrical speciﬁcations

AC/DC Power Supply - INPUT FIT PRO MAX

Motor Control Unit FIT PRO MAX

AC/DC Power Supply - OUTPUT FIT PRO MAX

Protections

Short circuit, overload, over voltage, over temperature.

Safety standards

SELV, UL62368-1, CSA C22.2 No. 62368-1, TUV EN62368-1 + A11, EAC TP TC 004, BSMI CNS14336-1

approved, EN55032 (CISPR32) Class A/B, EN61000-3-2/3, EN61000-4-2/3/4/5/6/8/11, EN55024,

EN61204-3, EN61000-6-2, BSMI CNS13438.

Working temperature

Max. 32ºC, mount in a dry and condensation-free area.

Safety measures

EVA Torque control, Voltage/current control, Mosfet temperature control

Voltage range 180-264 Vac 180-264 Vac 180-264 Vac

254-370Vdc 254-370Vdc 254-370Vdc

Frequency range 47-63Hz 47-63Hz 47-63Hz

AC current (230VAC) 5.5A 9A 11A

Nominal power 1200VA 2000VA 2400VA

Power factor (type) >0.9 >0.9 >0.9

Control input DMX512 DMX512 DMX512

Motor PMSM 3xDC Output RPM range RPM range RPM range

10-100% 10-100% 10-100%

IP rating IP20 IP20 IP20

Dimensions housing 660x185x115 mm (cable gland on bottom)

DC bus voltage (stabilized) 26Vdc 28Vdc 28Vdc

DC bus current 46A 71A 86A

EVAstream Electrical connections - PCB Settings EVAstream Electrical connections - PCB Settingswww.evaoptic.com8 9

4 Electrical installation

Electrical shock hazard. Fatal injury will occur. Switch off all electricity near the pool before

performing the electrical installation.

6DANGER

Connect the cables from the EVAstream Turbine to the Motor Control Unit:

l Make sure the cables are properly finished (as shown in the photo). Dismantling length

should be 16 mm.

l Place the red, yellow and blue cable (do not change the colors of the cables) in the

terminal block (like the yellow and blue cables in the drawing).

l Secure the cables by closing the orange clamps in the terminal block (with the T-LOX

knee lever connection) with a standard screwdriver (like the red cable in the drawing).

If the cables are not long enough, they can be extended:

You can extend the cable from the Turbine to the Motor Control Unit with max. 20 m. Use the

EVA CCB 16x25 connection box with a 25 mm2or 35 mm2cable.

Go to the next step for installation with an extension for the turbine cables or go directly to step

4.2 if extending the cables is not necessary.

L PEN

4.1 Connect EVAstream turbine to Motor Control Unit

Dismantling cable

Length 16 mm

Cable connections in Motor Control Unit

Connect the EVAstream turbine cables to the Connection box (EVA-CCB-16x25)

 l Connect the cables (3x1x25mm2 cable) attached to the EVAstream turbine to the

connection box.

l The cable connection box must be placed above the ground, in an accessible place.

l Always lay the cables in separate conduits from the EVAstream turbine to the

Motor Control Unit.

Connect the Connection box (EVA-CCB-16x25) to the Motor Control Unit

l Use the EVA-C25M1-x cables (to a maximum cable length of 20 m) to connect the

Connection box with the Motor Control Unit.

l Make sure the cables are properly finished (as shown in the photo). Dismantling length

should be 16 mm.

l Use red, orange and black cables (as shown in the illustration and photo). Do not change

the colors of the cables!

6CAUTION

Electrical shock hazard. Risk of electric shock due to leakage of current:

- Never connect the product to the main power before the installation is finished.

Color scheme of the cables in the Connection Box

Screw the cables into the correct holes

Correct use of the cables in the Connection Box

Dismantling cable

Length 16 mm

EVAstream Electrical connections - PCB Settings EVAstream Electrical connections - PCB Settingswww.evaoptic.com10 11

Overview of an EVA Piezo configuration (You can have one or both units)

What kind of control unit are you going to use?

EVA Piezo3 and/or EVA Piezo SQ3/SQ4: Go to step 4.2

Only the EVA experience web app?

No electrical connection is needed, go directly to step 4.3

4.2 Connect EVA Piezo to Motor Control Unit

General

l You can install only an EVA Piezo3 or SQ3/SQ4, or you can install both.

l The illustration shows the back side of the EVA Piezo SQ4.

l The buttons of the Piezo SQ3 are installed similar to the first three buttons of the

Piezo SQ4.

l You can put multiple cables into one port.

l Always check the wire coloring of the Pïezo and 12Vdc polarity before installation.

l To extend the cables always use a minimum core diameter of 0.25mm2 with a maximum

cable length of 30 metres. We recommend using cable type LiYY 16 x 0.25mm2

(Lapp Unitronic) or similar.

EVA Piezo3

l Connect the 7 wired cable from the EVA Piezo3 to the Control Print of the Motor Control

Unit on the indicated numbers.

Piezo SQ3 / SQ4

l Connect the blue and one of the red cables from the EVA Piezo SQ3/SQ4 to the Control

Print of the Motor Control Unit.

l Combine the black and the remaining red cables from the EVA Piezo SQ3/SQ4 and

connect to the Control Print of the Motor Control Unit. Group the wires 7, 9, 11, 13, 15, 17, 19,

and 21 to the Piëzo 4 switch, sw 9 (always use a cable with a minimum core diameter of

0.5mm2).

1 2

3 4

5 6

11 12

13 14

15 16

17 18

19 20

21 22

23 24

25 26

27 28

29 30

31 32

Electrical connections on the control print of the Motor Control Unit

EVAstream Electrical connections - PCB Settings EVAstream Electrical connections - PCB Settingswww.evaoptic.com12 13

4.3 Finishing the installation of the Motor Control Unit

Electrical shock hazard. Fatal injury will occur. Switch off all electricity near the pool before

performing the electrical installation.

6WARNING

Connect the Motor Control Unit to the mains (230 VAC; 16 A)

l Connect the 3 wired cable (230 VAC; 16 A) to the Motor Control Unit on the

indicated L. N. and PE.

l Connect an on/off button (power switch) to the socket and install near to the pool.

L PEN

230 VAC;

16 A

5 PCB Settings - General information

5.1 Preparation

Check if the electrical connections are installed correctly

5.2 EVAstream LEDs

Orange:

DMX is connected or PCB set as master

Green flashing with high sequence:

Starting software on PCB

Green flashing with sequence of 1 sec:

PCB is ready

How do you want to use your EVAstream?

Controlling with EVA Experience web app Go to chapter 6

Options:

lEVAstream + EVA LED underwaterlighting + EVA Piezo

lEVAstream + EVA LED underwaterlighting

lOnly EVAstream

Controlling without EVA Experience web app Go to chapter 7

Options:

lEVAstream controlled by EVA Piezo

lEVAstream controlled by EVA AA-77-SL (DMX)

EVAstream Electrical connections - PCB Settings EVAstream Electrical connections - PCB Settingswww.evaoptic.com14 15

6 Controlling with EVA Experience web app

6.1 Technical tablet requirements

The EVA Experience Controller can only be operated with a touchscreen tablet,

not with a smartphone.

We recommend a screen size of 9.7 inch to 11 inch for optimal functioning of the web environment.

The following tablet operating systems are generally suitable:

l Android tablets with Android version 12 or higher.

l Apple tablets with iOS 15.3 or higher.

6.2 Network connection

An internet connection is not required to operate the EVA Experience Controller with a tablet. However,

the tablet must be connected to the same WiFi network as the controller. There are 2 options for this:

1. New network (Access Point Mode)

Create a new WiFi network with the EVA Experience Controller, and connect the tablet to this network.

This option is suitable if the home network does not provide sufficient coverage around the pool:

l Due to the EVA Experience Controller’s own network, it is not necessary to further expand the

cover age of the home network.

l Your device is not connected to the internet.

2. Home network

Connect the tablet and the EVA Experience Controller to the home network. This option is preferred if

the home network provides sufficient coverage around the pool:

l The tablet remains connected to the home network while operating the

EVA Experience Controller.

l Switching networks on the tablet is not necessary to operate the controller.

WiFi networks of 2.4 GHz are supported.

1. Setting the Printed Circuit Board (PCB):

Go to the green Printed Circuit Board (EVA SP-ECA-PRO). This is located in the Motor Control Unit

of the EVAstream or in a separate power supply box.

Set the Rotary switches at 000

2. Turn WIFI on for installation

On the green Printed Circuit Board, set the ENA WIFI button to ON by sliding switch 2 to the right.

The green Printed Circuit Board (EVA SP-ECA-PRO) is the master in all cases for control. The EVA

LED underwater lighting and EVA Piezo can be linked to this if desired.

Rotary

switch 1

WIFI

turn On

Rotary

switch 2

Rotary

switch 3

6.3 Setting the PCB and WIFI

Before you want to connect to the home network or create a new network, the rotary switches must

first be set correctly and the WIFI must be switched on.

EVAstream Electrical connections - PCB Settings EVAstream Electrical connections - PCB Settingswww.evaoptic.com16 17

When the rotary switches of the Printed Circuit Board (EVA SP-ECA-PRO) are set to 000, the

EVA Piezo has the following functions:

EVA Piezo control options:

Button 1: On / stand-by (pause)

Button 2: Slowdown (in 5% increments)

In stand-by start on 30%

Button 3: Speed up (in 5% increments)

In stand-by start on 100%

Button 2+3: Child lock

Button 4: On / Off

6.4 New network conﬁguration (AP mode)

Create a new WiFi network with the Printed Circuit Board (PCB) and connect the tablet to this network.

This option is suitable if the home network does not provide sufficient coverage around the pool.

Connect tablet to Printed Circuit Board (PCB):

Open the screen on the tablet with WiFi connections, and connect to the network:

EVAcontroller AP ###### (or via IP 192.168.4.1)

A screen with the EVA logo will automatically appear. Click on Continue under the logo.

Connect Printed Circuit Board (PCB) to new network:

The following setup screen opens automatically:

1. Select AP Mode next to Network Mode.

2. Enter a self choosen Name for the new network next to Network SSID (only letters and numbers).

3. Enter a self chossen Password next to Password. Minimum 8 characters!

4. Check if evacontroller is filled in next to Hostname.

5. The other settings usually do not need to be changed. Click the save icon at the top right.

Self choosen Name

Self choosen Password

EVAstream Electrical connections - PCB Settings EVAstream Electrical connections - PCB Settingswww.evaoptic.com18 19

Connect the tablet to home network:

Open the screen with WiFi connections on the tablet and connect to the new network.

Disconnect the wifi connection on the Printed Circuit Board (PCB):

On the Printed Circuit Board (PCB), set the ENA WIFI button to OFF again (slide switch 2 back to the

left). The PCB is now connected to the new network.

WIFI

turn Off

3Connect tablet to EVA Experience web app environment:

Go to your internet browser and enter the following address in the address bar:

http://evacontroller.local (or via IP 192.168.4.1)

You will see the following screen:

The pop-up provides instructions for creating an EVA shortcut icon on your tablet’s desktop

(for easy access to the EVA Experience web app environment in the future).

1. Click on the share icon to the right of the address bar.

2. Select Add to Home Screen.

3. Name the icon EVAstream and select Add.

4. The icon is now added to your tablet’s desktop.

Apple IOS

Android

Altri manuali per EVAstream

Indice

Altri manuali EVA Pompa dell'acqua

EVA

EVA EVAstream Guida

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente