Everdure DWF126SS Guida
INSTALLATION, OPERATION
& MAINTENANCE INSTRUCTIONS
FOR EVERDURE DISHWASHERS
Models Included:
DWF126SS
KIMBERLEY
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
Compartment A:
Fill main-wash detergent.
Compartment B:
Fill pre-wash detergent.
(refer to instructions in section 3)
Mechanical indicator C.
Check the rinse aid level
Load the baskets
Select a programme
Close the door, t urn on the water tap and press the Start/Reset button. The machine will begin the cycle
in approximately 10 seconds.
Switch off the appliance
Turn off the water tap,
unload the baskets
Fill the detergent dispenser
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better. Unload the appliance, starting from the lower basket.
Changing the programme
Add forgotten dishes in the
dishwasher.
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions in section 4
Press the Programme button until the selected programme lights up.
( Refer to section “Operation instructions”)
When the working cycle has finished, the buzzer of the dishwasher will sound 8 times, then stop.
Turn off the appliance using the ON/OFF button.
If the appliance is switched
off during a wash cycle.
WARNING!
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
as it was prior to being switched off.
Switch on the appliance
Press the On/Off button to switch on the appliance. Open the door.
1.Press the Start/Pause button to stop the dishwasher.
2.Wait 10 seconds before you open the door completely.
3.Add the forgotten dishes.
4.Close the door, press the the dishwasher willStart/PAUSE button,
continue its cycle in approximately 10 seconds.
Electric indicator on control panel.
Quick Operation Guide
For detailed operating instructions, please refer to the corresponding content under “Operating
Instructions” in section 2
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Hold down the Start/PAUSE button for more than 3 seconds to cancel the running programme.
3. Select a new programme.
4. Restart the dishwasher.
C
A B
Open the door carefully.
Hot steam may escape
when the door is
opened.
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
NOTE:
Dear Customer,
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Pass it on to any subsequent
owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installation Instructions and
Troubleshooting Tips, etc.
The manufacturer, following a policy of constant
development and updating of the product, may
make modifications without giving prior notice.
Read this Manual
Before Calling for Service
Keep it to refer to it at a later date.
If you can not solve the problems by yourself ,
please ask for the help of professional technicians.
Dishwasher Features......................................................3
5) Prior using for the first time...........................................7
6) Loading the Dishwasher Basket...................................10
Attention before or after loading the Dishwasher
Baskets........................................................................10
8) Maintenance and cleaning...........................................15
Filtering System..........................................................15
Caring for the Dishwasher..........................................17.
A. Fill the Rinse Aid Dispenser.................... .. .......7....... ...
B. Function of Detergent .................................8
............
Loading the upper Basket ........................ ..................11....
Loading the Lower Basket ...................... ...........11..
Cutlery Basket............................................................12
7) Starting a washing programe.......................................13
Wash Cycle Table.......................................................13
Turning on the Appliance.............................................14
Change the Programme...............................................14....
At the End of the Wash Cycle.....................................14
4) Installation instruction............................... .....................4..
Positioning the Appliance...............................................4..
Water Connection...........................................................5.
Power Connection..........................................................4.
Start of dishwasher.............................................................6..
9) Troubleshooting Tips........................................... .......18..
Before calling for service.............................................18.
Error codes................................................................19.
2) Safety Information.........................................................2
3) Operating Instructions....................................................3
Control Panel..................................................................3
1) Technical Information....................................................1
.......
.......
...
Anti Flood Device............................................................5
850
600
580
1175
Height : 850mm
Width : 600mm
Depth : 580mm
Voltage connected Load : see rating label
Water pressure: 0.04-1.0MPa
Hot water connection : max 60 degrees
Power supply: see rating label
Capacity: 12 Place settings
1
1. Technical Information
SAVE THESE INSTRUCTIONS
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY
WARNING! PROPER USE
2.IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
WARNING!
WARNING! HYDROGEN GAS IS EXPLOSIVE
Under certain conditions, Hydrogen gas may be produced in a hot-water system that has not been used
for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used
for such a period, before using the dishwasher turn on all hot-water faucets and let the water flow from
each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable,
do not smoke or use an open flame during this time.
When using your dishwasher, follow the below basic precautions including the following:
· Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.
· Do not operate your dishwasher unless all enclosure panels are properly in place. Ensure you press the
“START / RESET” button prior to opening the Dishwasher whilst it is operating to avoid water spray.
Please also ensure all care is taken whilst opening the door as hot steam may also be present.
· Do not place any heavy objects or stand on the door when it is open as this could overturn the
dishwasher.
· When loading items in to the dishwasher:
o Locate sharp items so that they are not likely to damage the door seal;
o Warning: knives and other utensils with sharp points must be loaded in the basket with their points down
or placed in a horizontal position.
· Do not wash plastic items unless they are marked dishwasher safe or the equivalent. Please check the
manufacturer’s recommendations for items that are not marked such as plastic, ceramic or pots.
· Use only detergent and rinse additives designed for an automatic dishwasher. Never use soap, laundry
detergent, or hand washing detergent in your dishwasher.
· Other means for disconnection from the supply must be incorporated in the fixed wiring with at least 3mm
contact separation in all poles.
• This Dishwasher is intended for single family domestic use only.
· The appliance is not intended for use by young children or infirm persons without supervision.
Ensure the dishwasher door is not open in full when unused to avoid potential tripping hazards.
· Warning: Dishwasher detergents can be extremely dangerous if swallowed as they are high in alkaline.
Avoid contact with skin and eyes and ensure children are not present when opening the door of the
dishwasher. Also check that the detergent receptacle is empty after completion of the wash cycle.
· If the supply cord is damaged, it must be replaced by the manufacturer or its service centre or a
similarly qualified person in order to avoid a hazard.
· Please dispose of the packing materials appropriately.
· Use the dishwasher only for its intended function.
· During installation, the power cord must not be excessively or dangerously bent or flattened.
· Do not tamper with controls.
· The appliance is to be connected to the water mains using the new hose set supplied. Do not reuse old
or existing hose sets.
2
10 11
Back View
Front view
3.Operation Instruction
3
Dishwasher Features
Control Panel
instructions before using it for the first time.
To maintain the best performance from your dishwasher, read all operating
IMPORTANT
Main Filter
Detergent Dispenser
Cup Shelf
Cutlery Basket
Coarse Filter
Rinse Aid Dispenser
Inlet pipe connector
Drain pipe connector
Lower Basket
Spray Arms
Upper Basket
1
5
6
7
8
9
10
11
3
2
4
1
2
3
4
5
6
7
8
9
56
2
1
3478
7
8Program selection knob: being used to select
desired wash program.
1Power button: To turn on/off the power supply.
2Power indicator: To show the power supply.
Delay time indicator :3, 6, or 9 hours can be selected.
4
5Delay button: press the button to select desired
delay time
3Rinse aid indicator: To come on when the
dispenser needs to be refilled.
6
Program indicator: To show washing program.
START/PAUSE button: being used to start or
pause machine.
3h
6h
9h
Electrical Requirements
Ensure the voltage and frequency of the power corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug, replace the socket, rather than using adaptors or the like as
they could cause overheating and burns.
Electrical Connection
Ensure appropriate
ground is evident
prior to use
GROUNDING INSTRUCTIONS
4.Installation instruction
Please see the rating label to identify the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with a
cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned for leveling, the height of the dishwasher
may be altered via adjustment of the screwing level of the feet. In any case,
the appliance should not be inclined more than 2 DEGREES TO ENSURE
CORRECT OPERATION
Positioning the Appliance
Power Connection
WARNING!
For personal safety:
DO NOT USE AN EXTENSION LEAD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
n
n
n
for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE
FROM THE POWER CORD.
EARTHING
CONNECTION
n
n
WARNING!
I mproper connection of the equipment earthing conductor can result in the risk of an
Check with a qualified electrician or service representative if you are in doubt whether the
appliance is properly earthed.
I f the plug does not fit properly. Do not modify the plug provided with the appliance.
n
n
n
4
electric shock.
Please have a qualified electrician to install a proper outlet.
To reduce the water remaining in the inlet hose, please close
the water connection after use.
WARNING!
5
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has
one, it is recommended that the hose be disconnected and the hole plugged.
WARNING!
ABOUT THE ANTI FLOOD DEVICE
How to Connect the safety supply hose
Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.
Turn water fully on before starting the dishwasher.
1
Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.
The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking the flow of
water in case of the supply hose breaking and when the air space between the supply hose itself and the outer corrugated
hose is full of water.
Turn off the water.
Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
room, from severe splashing.
Unscrew The safety supply hose from the faucet..
3
2
1
How to Disconnect the safety supply hose
2
3
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the minimum
consult our Service Department for advice.
COLD WATER CONNECTION
HOT WATER CONNECTION
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and
damage the appliance.
The water supply to the appliance can also be connected to the house hot water line (centralized system, heating system),
as long as it does not exceed a temperature of 60 C. In this case, the wash cycle time will be shortened by about 15 minutes
and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those for the connection to the
cold water line.
The following things should be checked before starting the dishwasher.
Start of Dishwasher
1 Whether the dishwasher is level and fixed in to position.
2 Whether the inlet valve is opened.
3 Drain hose connected has the plug in waste tee been opened for drainage
4 Whether there is leakage at the hose connections
5 Whether the power cord is connected and power switched on.
6 Whether the inlet and drain hoses are kinked (as per page 4).
7 All packing materials and printings should be taken out from the dishwasher.
8 Can the spray arms rotate freely
If the sink is 100cm higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
How to Drain Excess Water From Hoses
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
Syphon Connection
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
The waste connection must be at a height of between 40 cm (minimum) and 100 cm (maximum)
from the bottom of the dish. The water drain hose should be fixed by a hose clip. The free end of
the hose must not be immersed in water.
6
Drain hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink, making sure to
avoid bending or crimping. Use the special plastic support that comes with the appliance. The free end of the hose
must be at a height between 40 and 100cm and must not be immersed in water.
Max 1000mm
Min 400mm
FRONT VIEW
Inlet pipe connectorDrain pipe connector
POWER OUTLET
SINK
DISHWASHER
Min 100mm
WARNING!
DO NOT BEND IN ANY WAY !
Before using your dishwasher for the first time:
5.Prior using for the first time
7
A. Fill the rinse aid dispenser
B. Fill in detergent
A. Fill the Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can leave
spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is designed to
use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser. To fill the
dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely black.
The volume of the rinse aid container is about 110ml.
Rinse Aid Dispenser
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
1
2
3
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated below.
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
When to Refill the Rinse Aid Dispenser
during the next wash. Don't forget to replace the cap before you close dishwasher door.
Clean up any rinse aid spilled during filling with an absorbent cloth to avoid excessive foaming
NOTE:
You can estimate the amount of rinse aid required from the colour of the optical level indicator “C” located next to
the cap. When the rinse-aid container is full. the whole indicator will be dark. As the rinse-aid diminishes, the size
of the dark dot decreases. You should never let the rinse aid level fall 1 / 4 full. The front panel also has a LED
indicator that will illuminate once you reach below the 1/4 level.
C (Rinse-Aid indicator)
1 2 3
Indice
Altri manuali Everdure Lavastoviglie
