Everdure OBES61 Manuale utente
SEE
1
2
3
3
4
4
5
5
6
6
7
7
SEE:
SEE:
SEE:
SEE:
SEE:
SEE:
SECTION/COMPONENT
Fan not working/noisy/ hitting its cover
Signal lamp not working / blinking
Electrical
Electrical
Electrical
Electrical
Electrical
EVERDURE BUILT IN ELECTRIC OVENS
CATEGORY
Electrical
Electrical
Fan
Transport
Electrical
Electrical
Electrical
Mechanical
Mechanical
Transport
Mechanical
Transport
Mechanical
Transport
Timer
Signal Lamp
Hinge
Oven Light
Oven Light
Timer
Oven Electrical Heating
Cooking
Cooking
Knobs
Damaged ( how to change )
PROBLEM(S)
Rear panel
Front Panel
Oven door
Wire& Catalytic Shelves
Side panels (built-in cooker)
Handle
Damaged ( how to change )
Appliance doesnt work at all
Ring (Circular) Heating Element not working
Top/Bottom/Grill Heating Element not working
Oven door handle loose/broken
Oven Elc. Heating Elements
Damaged ( how to change )
Damaged ( how to change )
Damaged ( how to change )
Digital Timer not working/Timer buttons stucking
Timer circuit stays open / closed
Oven light not turning on/off
Oven light button not working
Oven/Hob Hinge noisy
Unhomogenious cooking/ Long cooking period
Knob stays locked/broken/loose/knob gasket loose
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 2 of 23
OBES63 FAULT CODES
To enter test mode follow the below steps;
Turn oven off at the electrical outlet
Press temperature buttons "PLUS" ( + ) & "MINUS" ( - ) together
TEST MODE
Each button has another function, from left to right;
Turn on oven at the electrical outlet while keeping the temperature + & - buttons depressed
POSSIBLE SOLUTION
POSSIBLE CAUSE
Thermostat cable maybe
loose
Thermostat may be
damaged
Thermostat contacts
may be damaged
ERROR DESCRIPTION
If cables are loose, check &
correct wiring
Replace the mode selector
cable if it is damaged
Change the mode selector if
the above solutions did not
Mode selector cable may
be loose / damaged
Change the thermostat cable if
it is damaged
Change the thermostat
Thermostat cable may
be loose/ damaged
Thermostat contacts
may be damaged
DISPLAYING MAINS FREQUENCY
5. All 7 SEGMENT DIGITS are on
4. FAN is switched on & all SYMBOLS are on
6. BUZZER is switched on
7. Leave test mode
The oven is in test mode when "tESt' is displayed in the temperature display & "Edxx" is diplayed in the clock display
1. RING heater & COOLING FAN is switched on & measured cavity temperature is displayed
2. Oven LIGHT is switched on
3. No functions set
Open circuit on the oven
temperature sensor
(thermostat)
Open circuit on the oven
temperature sensor
(thermostat)
Mode selector short/open
circuit
There are 3 different signals to choose from
CHANGING THE BUZZER SIGNAL
Keep pressed ( - ) MINUS for a second & you will hear a signal
Thermostat cable may
be loose/ damaged
ERROR CODE
Err1 (failure 1)
Err2 (failure 2)
Err3 (failure 3)
Press ( + ) PLUS button & the mains frequency is displayed in the clock display
When pressed repeatedly, the signal frequency will change
If cables are loose, check &
correct wiring
Change the thermostat cable if
it is damaged
Change the thermostat
If cables are loose, check &
correct wiring
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 3 of 23
EVE
Electrical component problems
TROUBLE SHOOTING
Fan hitting its cover / working noisy
REMOVE THE FAN COVER.
PUSH BACK THE FAN WINGS AND
REPLACE THE COVER.
DOES IT STILL HIT TO COVER ?
CHANGE THE FAN COVER. DOES IT
SOLVE THE PROBLEM?
Fan problems
YES
Fan not working
IS THE WIRING OF FAN MOTOR
CORRECT ACCORDING TO THE
WIRING DIAGRAM ?
THE FAN SHOULD NOT HIT / OR BE
LOCKED ONTO THE FAN COVER.
YES
NO
CORRECT THE WIRING OF FAN MOTOR
PLEASE SEE :
FAN HITTING ITS COVER
NO
NO
CHANGE THE FAN.
DOES IT SOLVE THE PROBLEM?
NO
CHANGE THE FAN MOTOR
WHEN OVEN SWITCH TURNED ON,
CAN YOU MEASURE VOLTAGE AT
FAN MOTOR ?
CHECK IF THE FAN MOTOR ASSEMBLY
SCREWS ARE FIXED CORRECLTY.
PROBLEM SOLVED ?
CORRECT THE WIRING OF OVEN
SWITCH - see circuit diagram
CONTROL THE WINDINGS OF FAN
MOTOR WITH OHMMETER.
ARE MOTOR WINDINGS DAMAGED?
YES
YES
CHECK IF THE ROTOR GOT LOCKED.
CORRECT THE POSITION
IF STILL GOT PROBLEM ;
CHANGE OVEN SWITCH
NO
NO
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 4 of 23
EVE
Electrical component problems
Signal lamp problems :
CHECK THE WIRING CONNECTION , IS IT
OK?
IS THE SIGNAL LAMP LED HARMED?
YES
CHANGE THE SIGNAL LAMP
BE SURE THAT THE SIGNAL LAMP
TERMINAL CONTACTS ARE OK WITH
OVEN SWITCH
NO
IF SIGNAL LAMP CABLE IS HARMED;
CHANGE THE SIGNAL LAMP
Signal lamp not working
Signal lamp blinking
CHECK THE WIRING CONNECTIONS
CAN YOU SOLVE THE PROBLEM ?
NO
YES
CHANGE THE SIGNAL LAMP
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 5 of 23
Electrical component problems
Digital timer buttons stucking
REMOVE TIMER
AND CORRECT THE POSITION OF
TIMER MANUALLY.
CHANGE THE TIMER BUTTONS
YES
IS THE TIMER AND FRONT PANEL HOLES
COAXIAL?
NO
Digital timer not working
IS THERE VOLTAGE AT TIMER TERMINALS?
IS TIMER DISPLAY VISIBLE ?
YES
NO
CHECK THE WIRING CONNECTION
pls see circuit diagram on user manual
NO
CHANGE DIGITAL TIMER
WHEN YOU SET THE TIMER , IS THERE
VOLTAGE AT TIMER RELAY TERMINAL ?
YES
NO
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 6 of 23
Electrical component problems
Oven light not working
CHECK THE WIRING CONNECTION AND
CORRECT.
( pls see circuit diagram )
DOES IT SOLVE THE PROBLEM?
CHECK THE ELECTRICITY OF OVEN LIGHT
IS THE LAMP DEFECTIVE
( BURNT OR LOOSE )?
OK
IS THE OVEN LIGHT BUTTON WORKING?
NO
NO
IS THERE VOLTAGE AT OVEN LIGHT
TERMINAL?
YES
PLUG OFF THE OVEN,
CHANGE ONLY LAMP
IS OVEN THERMOSTAT AND SWITCH TURNING ON ?
CHANGE THE OVEN LIGHT BODY ( WITH WIRING )
CHECK THE OVEN LIGHT WIRING CONNECTION
pls see circuit diagram
NOT OK
YES
CHECK THE OVEN LIGHT BUTTON WIRING
CONNECTION
( pls see circuit diagram )
YES
YES
NO
CHECK THE WIRING CONNECTIONS AND
RELEASE THE OPEN CIRCUIT.
NO
IF NOT OKEY ;
CHANGE THE OVEN LIGHT BUTTON
CHANGE OVEN SWITCH - IF DEFECTIVE
CHANGE THERMOSTAT - IF DEFECTIVE
NO
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 7 of 23
Before putting on the knob ; be sure the knob segment and knob spring is set correctly
Mechanical component problems : Hinges & Knobs
Glass lid angle less than 90°/ more
than 100°
IS THE LID HINGE COUNTERPART FIXED ?
FIX THE HINGE COUNTERPART.
IS IT STILL LESS 90°/ MORE THAN 100°?
NO
HINGE PROBLEMS
Oven door hinge noisy
KNOB PROBLEMS
REPLACE GASKET.
( KNOB GASKETS MUST BE SET PROPERLY ON
BOTH SIDES )
KNOB LOOSE
IF THE SPIRAL KNOB SPRING IS REMOVED,
ASSEMBLE A NEW KNOB RING.
KNOB GASKET GETTING OUT OF ITS
PLACE
knob spring
knob segment
knob ring
IF NOT OKEY ;
CHANGE THE KNOB GASKET
Knob gaskets must be controlled on both
sides - to set properly.
IF KNOB SPRING IS AVAILABLE,
CHANGE THE KNOB.
CHANGE OVEN DOOR HINGE
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 8 of 23
Cooking problems
Oven doesnt work
REGULATE THE TIMER
pls.see user manual
CHECK THE WIRING CONNECTIONS ARE
CORRECLTY DONE ? ( please see circuit diagrams )
IS THE HEAT ADJUSTED WITH OVEN HEATER
CONTROL SWITCH?
OK
TIMER ( IF AVAILABLE ON MODEL ) REGULATED
OR WORKING PROPERLY ?
YES
NO
EXCHANGE THE APPLIANCE
YES
ADJUST THE HEAT
See user manual for detailed
instructions
NO
CHECK THAT THE PLUG IS ON/OFF?
CHECK THE TERMINAL BOX HAS VOLTAGE ?
OK
CHECK THE ELECTRICAL HEATING ELEMENTS OF
OVEN ARE WORKING PROPERLY?
YES
NO
IF TIMER NOT WORKING
PROPERLY :
REFER TO TIMER PROBLEMS
SEE CHAPTER :
OVEN HEATING ELEMENTS
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 9 of 23
Cooking problems
IS THE THERMOSTAT BULB BRACKET FIXED
CORRECTLY?
Oven cooking unhomogeniously /
long cooking period
CHECK SHELF LOCATIONS AND HEAT VALUES,
CHECK THE COOKING PERIOD
OK
CHECK WIRING CONNECTIONS ;
BE SURE THAT THE OVEN ADJUSTED AS
APPROPRIATE FOR THE VOLTAGE
( REFER TO LABELS )
YES
FOR BEST COOKING
PERFORMANICE ; REFER TO
THE INSTRUCTIONS
INDICATED IN THE USER
MANUAL
IS THE FAN ( IF AVAILABLE )
CORRECTLY WORKING?
YES
REPLACE THERMOSTAT BULB
BRACKET
NO
PLEASE REFER TO
" FAN PROBLEMS "
NO
MODELS: OBES61
OBES62
OBES63
SERVICE MANUAL BUILT IN ELECTRIC OVENS
Page 10 of 23
Altri manuali per OBES61
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Everdure Forno
Everdure
Everdure UFCW661 Guida
Everdure
Everdure OBES64 Guida
Everdure
Everdure UFEE61 Manuale di installazione e funzionamento
Everdure
Everdure OBES66 Guida
Everdure
Everdure OBES61 Manuale utente
Everdure
Everdure OBEGS601 Guida
Everdure
Everdure UFGS69 Manuale del proprietario
Everdure
Everdure OBEP601 Guida
Everdure
Everdure OBES601 Manuale di installazione e funzionamento
