EVO Gimbals Rage Gen.2 Manuale utente
20810 Sockeye Pl #200
Bend, OR 97701
Support and Sales Quesons:
Tel: (866) 977-6688 Monday to Friday 9AM to 5PM Pacific Time
or email support@evogimbals.com
EVOGimbals.com
English Manual v2.0
CONTENTS
Packing List 1
Disclaimer and Warning 2
Get to Know The EVO RAGE Gen2 7
Preparing and Charging the Baeries 8
Camera Installaon 9
Balance Adjustment 11
Gimbal Controls 14
Start Up 15
Gimbal Control Modes 16
Calibraon 17
Firmware Upgrade & Panasonic CCI Cable 19
SONY CCI Cable 20
App Operaon 21
Product Specificaons 23
Motor Power Sengs 24
Warranty 25
Notes 27
1 2
PACKING LIST DISCLAIMER AND WARNING
The EVO RAGE Gen2 comes with the following items. If any item is missing, please
contact EVO Gimbals.
26500 Li-ion Charger
Camera Mount Screw
Storage Case
Manual
26500 Li-ion Baery
Lens Support Screw
EVO RAGE Gen2 Gimbal
1
1
1
2
1
1
1
Lens Support Bracket
1
1
Micro USB Cable
1
Thank you for purchasing the EVO RAGE gen2. The informaon contains herein affects your safety and your
legal rights and responsibilies. Read this enre document carefully to ensure proper configuraon before
use. Failure to read and follow the instrucons and warnings herein may result in serious injury to you or
bystanders, or damage to your device or property.
EVO Gimbals reserves the right of final explanaon for this document and all relevant documents relang to
the RAGE Gen2, and the right to make changes at any me without noce. Please visit EVOGimbals.com for
the latest product informaon.
By using this product, you hereby signify that you have read this document carefully and that you understand
and agree to abide by the terms and condions herein. You agree that you are solely responsible for your own
conduct while using this product, and for any consequences thereof. You agree to use this product only for
purposes that are proper and in accordance with all terms, precauons, pracces, policies and guidelines
EVO Gimbals has made and may make available.
EVO Gimbals accepts no liability for damage, injury or any legal responsibility incurred directly or indirectly
from the use of this product. Users shall observe safe and lawful pracces including, but not limited to, those
set forth herein.
The following terms are used throughout the product literature to indicate various levels of
potenal harm when operang this product.
WARNING: Procedures, which if not properly followed, may incur property damage, grave accident, or
serious injury.
CAUTION: Procedures, which if not properly followed, may incur property damage and serious injury.
NOTICE: Procedures, which if not properly followed, may incur property damage or minor injury.
Tripod Stand
2Sony & Panasonic CCI Cables
3 4
DISCLAIMER AND WARNINGDISCLAIMER AND WARNING
Battery Safety Guidelines
1. Prevent the baeries from coming into contact with any kind of liquid. Do not leave baeries out in the
rain or near a source of moisture. Do not drop the baeries into water. If the inside of the baery comes in
contact with water, chemical decomposion may occur, potenally resulng in the baery catching on fire,
and may even lead to an explosion.
2. If the baery falls into water with the stabilizer during use, take it out immediately and put it in a safe and
open area. Maintain a safe distance from the baery unl it is completly dry. Never use the baery again, and
dispose of the baery properly as described in the Baery Disposal secon below.
3. If the baery catches fire, use water, water spray, sand, fire blanket, dry powder, or carbon dioxide fire
exnguisher immediately to put out the fire. Please exnct the fire by applying the methods recommended
above according to the actual situaon.
4. Never use non-EVO Gimbals baeries. If replacement or backup is needed, please purchase new baeries
from EVO Gimbals' official website or authorized channels. EVO Gimbals takes no responsibility for any
damage caused by non-EVO Gimbals baeries.
5. Never use or charge swollen, leaky, or damaged baeries. Never use or charge if the baery smells, or
overheats (exceeding maximum temperature of 160°F / 71°C). If your baeries are abnormal, contact EVO
Gimbals for further assistance.
6. The baery should be used within the temperature range from -10° C to 50° C. Use the baery in
environments above 50° C can lead to a fire or explosion. Use of baery below - 10° C can lead to serious
baery damage.
7. Do not use the baery in strong electrostac or electromagnec environments. Otherwise, the baery
protecon board may malfuncon.
8. Do not disassemble or use any sharp object to puncture the baery in any way. Otherwise, the baery
may leak, catch fire or explode.
9. Do not mechanically strike, crush, or throw the baery. Do not place heavy objects on the baery or
charger.
10. Electrolytes inside the baery are highly corrosive. In case of accidental contact of any electrolytes with
your skin or eyes, rinse immediately with water for at least 15 minutes and seek medical advice as soon as
possible.
11. Do not use the baery if it has been involved in a crash or heavy impact.
12. Do not heat the baery and never put the baery in a microwave oven or in a pressurized container.
Warning
Read the ENTIRE User Guide to become familiar with the features of this product before operang. Failure to
operate the product correctly can result in damage to the product or personal property and cause serious
injury. This is a sophiscated product. It must be operated with cauon and common sense and requires
some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in
injury or damage to the product or other property. This product is not intended for use by children without
direct adult supervision. DO NOT use with incompable components or in any way otherwise as menoned
or instructed in the product documents provided by EVO Gimbals. The safety guidelines herein contain
instrucons for safety, operaon and maintenance. It is essenal to read and follow all of the instrucons and
warnings in the User Guide, prior to assembly, setup or use, in order to operate the product correctly and
avoid damage or serious injury.
Safe Operation Guidlines
CAUTION:
1. The RAGE Gen2 is a high-precision control device. Damage may be caused to The RAGE gen2 if it is
dropped or subject to external force, and this may result in malfuncon.
2. Make sure the rotaon of the gimbal axes is not blocked by external force when The RAGE Gen2 is turned
on.
3. The RAGE Gen2 is not waterproof. Prevent contacts of any kind of liquid or cleaner with The RAGE gen2.
It is recommended to use dry cloth for cleaning.
4. Protect The RAGE Gen2 from dust and sand during use.
WARNING:
To avoid fire, serious injury, and property damage, observe the following safety guidelines when using,
charging, or storing your baeries.
5 6
DISCLAIMER AND WARNINGDISCLAIMER AND WARNING
13. Do not place the baery cell on a conducve surface (such as a metal desk surface).
14. Prevent use of wires or other metal objects that could cause posive and negave short-circuit to the
baery.
15. If the baery terminal is dirty, wipe it with a clean, dry cloth. Otherwise it will cause a bad baery
connecon, which may result in energy loss or charging failure.
Battery Charging
1. Do not aach the baeries to a wall outlet or car charger socket directly. Always use a EVO Gimbals
approved adapter for charging. EVO Gimbals takes no responsibility if the baery is charged using a non-EVO
Gimbals charger.
2. Do not put the baery and charger near flammable materials or on flammable surfaces (such as carpet or
wood). Never leave the baery unaended during charging to prevent an accident.
3. Do not charge the baery immediately aer use, because the baery temperature may be too high. Do not
charge the baery unl it cools down to normal room temperature. Charging the baery with its temperature
over 40°C or lower than 15°C may lead to leakage, overheang, or damage.
4. Examine the charger before use, make sure there is no damage to the enclosure, cord, plug, or other parts.
Never use a damaged charger. Do not clean the charger with any liquid containing alcohol or other flammable
solvents. Disconnect the charger when not in use.
Battery Storage
1. Keep baeries out ohe reach of children and pets.
2. Do not leave the baery near heat sources such as a furnace or heater, or inside a vehicle on hot days.
Never expose the baery in any environment with temperatur over 60°C. The ideal storage temperature is
22°C-28°C.
3. Store baeries in a dry environment.
4. Do not leave the baery unused for too long aer it has been completely discharged to prevent
over-discharge of baery which may result in baery damage and permanent failure.
Battery Maintenance
1. Never use the baery when the temperature is too high or too low.
2. Do not store the baery in any environment with a temperature of over 60°C.
Transportaon Noce
1. Discharge the baery power to 5% or lower before carrying the baery on an airline flight. Only discharge
the baery in a fireproof locaon, ideally in a dry and open area.
2. Do not store or transport baeries together with metal objects such as eyeglasses, watch, and jewelries,
etc.
3. Do not transport damaged baeries. When transporng, be sure to discharge the baery to les than 50%.
Baery Disposal
1. Dispose the baery in a specific recycling area only aer a complete discharge. Do not throw away the
baery in regular trash containers. Strictly follow your local regulaons regarding the disposal and recycling
of baeries.
NOTICE:
Battery Use
Make sure the baeries are fully charged before each me of use.
Battery Charging
The baery will stop charging automacally when it is full. Disconnect the baeries from the charger when
fully charged.
Battery Storage
1. Discharge the baery to 40%-65% if it will NOT be used for over 10 days. This can greatly extend the
baery life.
2. The baery enters hibernaon mode when voltage gets too low. Charge the baery will bring it out of
hibernaon.
3. Remove baeries from the stabilizer when not in use and store them in a specialized container.
Battery Disposal
If the baery cannot be fully discharged, do not leave it in the recycling box, but contact a professional
baery disposal/recycling agent for further assistance.
7 8
PREPARING AND CHARGING THE BATTERIESGET TO KNOW THE EVO RAGE Gen2
Before using your new EVO Rage Gen2 for the first me, please be sure to use the provided baery charger
to fully acvate and charge the included baeries. Failure to charge the baeries before the first use can
permanently damage the baeries and decrease their overall lifespan.
NOTICE: Camera is not included in product package, and shall be bought separately.The depicons provided
herein are for reference only.
Thumb Screw
CCI Input
Vercal Arm
Mount Plate Screw
Baery Level
Joysck
On /Off
Zoom Control
Status Indicator Lights
Horizontal Arm
Thumb Screw
Lens Support Bracket
Camera Mount Screw
Camera Mount Plate
Support Bracket Screw
Pan Axis Motor
Micro USB Port
Mode Buon
1/4”-3/8”
Threaded Hole
Handle / Baery
Compartment
Mico USB Port
Charger & Battery Description
Charger Specificaons
Name: EVO 26500*2 Li—ion baery charger
Model: IMR-26500 (x2)
Input: 5V=2400mA
Output: 4.2V=1200mA (x2)
Solid RED light when charging.
Solid BLUE light when fully charged.
Battery Specifications
Name: EVO 18650 Li—ion baery
Model: IMR 18650
Capacity: 2000mAh
Voltage: 3.7V
NOTICE:
1.Please read the disclaimer and warning herein as well the descripon
on the baery label carefully before using the baeries.
2. The ZC-26500-2 charger is for charging EVO’s IMR 26500 Li—ion
Baery only. Do not charge baeries of other models or brands,
otherwise It may lead to an accident.
Please use and charge baeries provided or approved by EVO Gimbals only. EVO Gimbals will not take
any responsibility for explosion, fire and/or accidents caused by non-EVO baeries.
9 10
CAMERA INSTALLATIONOPERATION OVERVIEW
Gimbal balance should be adjusted before moving to Inverted Posion. Do not rotate the handle while
turning it straight up or down to switch between Normal and Inverted Posion.
NOTE: The size of the camera and lens will affect balance condions when transioning to the Inverted
Posion. For certain camera models, balance should be adjusted aer transion to Inverted Posion. Most
camera and lens combinaons are compable switching between Normal to Inverted Posion but some
larger size cameras and lenses may not be compable because of the larger dimensions of the camera body
and posion of center of gravity.
Mount the camera in parallel with the mounng plate,
match the 1/4" Threaded Hole at the boom of the
camera with the empty slot of the mounng plate. Move
the camera as close as possible to the Tilt Motor , and
ghten the Camera Mounng Screw to fix the camera
to the mounng plate.
NOTE: Do not power on the stabilizer before the camera
is properly mounted.
Operating Methods Mount The Camera
Normal Position Inverted Position
2
2
1
1
There are two main operang posions used when shoong video with the EVO Rage Gen2 - Normal &
Inverted. The inverted posion requires that you properly balance your gimbal so that the handle does not
hit the camera while switching between Normal to Inverted.
Mount the camera in parallel with the mounng plate,
match the 1/4" Threaded Hole at the boom of the
camera with the empty slot of the mounng plate. Move
the camera as close as possible to the Tilt Motor , and
ghten the Camera Mounng Screw to fix the camera
to the mounng plate.
NOTE: Do not power on the stabilizer before the camera
is properly mounted.
IMPORTANT: Before mounng your camera please make
note of your cameras total weight. You will need to know
this in order to properly adjust the motor power sengs
for best performance. Please see pg. 24 for more details.
11 12
BALANCE ADJUSTMENTBALANCE ADJUSTMENT
Step One:
Aer camera is mounted to the mounng plate,
loosen the thumb screw lever underneath the
mounng plate to allow forward and backward
sliding of the plate.
NOTE: The thumb screw lever direcon can be
adjusted by pulling the lever straight out and
rotang the lever to the desired direcon.
Step Two:
Push the camera forward or backward to find its level balance.
Once the camera can stay sll and almost level with its lens
facing front, ghten the thumb screw lever.
Loosen Thumb Screw . Adjust the balance by
sliding the Roll Axis Arm unl the camera
stays horizontaly balanced. Complete this step
by ghtening the Thumb Screw to secure the
Roll Axis arm.
Step Three:
Loosen Tilt Motor thumb screw . Adjust the
balance by sliding the Tilt Axis Arm unl the
camera stays vercally balanced while poinng
up.
Balance Adjustment on The Tilt Axis
Balance Adjustment on The Roll Axis
2
2
2
2
1
1
1
1
MODE
W
T
13 14
BALANCE ADJUSTMENT GIMBAL CONTROLS
Balance Adjustment on The Pan Axis
Loosen Thumb Screw . Adjust the balance by sliding the Pan Axis Arm unl the camera stays
horizontaly balanced. Complete this step by ghtening the Thumb Screw to secure the Pan Axis
arm.
2
2
1
1
Baery Level
Joysck
Power On/Off
Zoom Control
Mode Buon
Baery Level Indicator
When powered on you will see quick yellow flashes for
3 seconds and then solid yellow for 1 second. Once fully
powered the light will turn blue and flash to indicate
baery level.
4 quick flashes means baery level of 75%-100%.
3 quick flashes means baery level of 50%-75%.
2 quick flashes means baery level of 25%-50%.
1 quick flashs means baery level of 0%-25%.
Zoom Control*
For SONY model cameras, the Zoom Control is used to zoom in by pushing down to “T” (ght). To zoom out,
push up to “W” (wide). *CCI Cable required, please be sure to use soware to set control protocol for SONY or
PANASONIC
Mode Buon
Please see Gimbal Control Modes on page 16.
Power ON/OFF
Power on the stabilizer by pressing the Power buon for 3 sec. Aer the stabilizer is powered on, the Power
buon can be used for camera shoong control (only aer the camera is connected via CCI to the stabilizer).
Single press the buon to take photos. Double press the buon to start video recording. Double press the
buon again to stop recording.
Joysck
Joysck controls the camera movement by turning the 3 axes up/down or le/right.
Indice
Altri manuali EVO Gimbals Accessori per fotocamere
