EVRY S-FIT Manuale utente
USER MANUAL
S-FIT
Foldable Electric Scooter
Thank you for choosing S-FIT electric scooter!
Following are instructions on how to use your brand new electric scooter.
(Instructions on how to have fun are not included. Hint: it’s impossible not to,
unless you are a robot.)
Contents
1. The Scooter & its Accessories (3)
2. Functions (4)
3. Assembling the Scooter (5)
4. Charging the scooter (6)
5. Driving the Scooter (7)
6. Safety Instructions (9)
7. Folding and Transporting (17)
8. Care and Storage (18)
9. Parameters (22)
10. Warranty (24)
1. The Scooter & its Accessories
Vehicle
Accessories
--------------------------------------------------------------------------------------
Fitting for wheels swap Screws x 2 Hex Wrench Charging Adapter
2. Functions
Mode Indicators
The control panel has 4 LEDs, which indicate the level of charge.
When the battery is in use, status indicators are lit. As the battery loses its
charge, the LED lights will flash and turn off, one by one.
Basic rule of thumb:
If all 4 LEDs are lit, the battery level is approximately 86-100% charged.
If 3 out of 4 LEDs are lit and one is blinking, the battery level is approximately
71-85% charged.
As you go down in charge level, you will see each subsequent LED begin to
flicker and eventually, go out.
The lowest charge level indicator may be white or green. When the vehicle is
in normal operation, the LED glows white. If the scooter is running in power
saving mode, the LED glows green. (Note: in power saving mode, the
maximum speed is 11 mph.)
3. Assembling the Scooter
1) Fix the steering rod and open the parking bridge.
2) Set the handlebars so they are perpendicular to the scooter deck.
3) Make sure that wires from the handlebar and the stem are properly
connected with a white connector.
4) Using a hex wrench, as found in the tool kit provided with your scooter,
tighten the screws on the handlebar.
5) Test the power. Press and hold the power button for 2 seconds to turn on
the scooter. The battery should be fully charged and you should see the
control panel light up. You can use the power button to turn the device on/off.
Press the power button twice in a row to switch between normal mode and
power saving mode.
4. Charging the scooter
Open the cover of the charging port, located near the front wheel of the
scooter. Connect the appropriate end of the charging adapter and connect
the other end to a nearby outlet.
5. Driving the Scooter
Follow normal safety practices, as with any motorized vehicle. We
recommend you wear a helmet and knee pads, just in case.
1) Power on the scooter using the power button. Check the battery level by
referencing the LEDs on the control panel to make sure you have a sufficient
charge.
2) Place one leg on the scooter and place the other leg on the ground.
3) Using the leg that is on the ground, propel the scooter so it begins to move
forward. Put the second leg on the scooter deck now, so both legs are off the
ground. Press the accelerate button to speed up. Note: only accelerate when
the scooter speed is beyond 3 mph.
4) Take your hand off the accelerate button in order to slow down. Energy
recovery systems kick in to help decelerate the scooter. If you need to
urgently stop, press down on the break handle, located on the left side of the
handlebars firmly to activate.
5) To turn, lean your body in the direction you want to move. For example, lean
your body toward your left to turn left and lean your body toward your right to
turn right. Turn the handlebars slowly in the same direction as your body to
complete the turn.
6. Safety Instructions
Avoid using your scooter in the rain, as wet surfaces create potentially
hazardous conditions.
Slightly bend your knees to better adjust to a rough terrain. If you are
traveling on a rough road, stick to low speeds (3 mph-6 mph).
While we don’t recommend using your scooter to enter into a room, elevator,
etc., if you attempt to do so, be careful not to injure yourself on the door
frames or edges.
Indice
Altri manuali EVRY Scooter
