Excelair EOHA24R Manuale utente
Infrared Outdoor Heater
Instruction Manual
Model: EOHA24R
IMPORTANT INFORMATION
Please carefully read the Operation Manual before using the infrared heater.
This Operation Manual contains the important information on your safety, as well
as some recommendations on proper use of the appliance and its maintenance.
Page | 2
TABLE OF CONTENTS
CONTENTS PAGE 2
SAFETY INSTRUCTIONS PAGE 3-4
MAIN FEATURES PAGE 5
TECHNICAL SPECIFICATIONS PAGE 5
HEATING AREA PAGE 6
BEFORE OPERATION PAGE 7
HEATING COMPONENTS PAGE 8
OPERATING THE HEATER PAGE 9-12
INSTALLATION PAGE 13-17
MAINTENANCE PAGE 18
WIRING DIAGRAM PAGE 18
TROUBLESHOOTING PAGE 19
WARRANTY INFORMATION PAGE 20
WHAT’S IN THE BOX
Heater fitted with flexible cord and plug.
Operating and Installation Instructions.
One small box contains 2 sets of Brackets.
One remote controller
Page | 3
SAFETY INSTRUCTIONS
During use of the infrared heater, it is necessary to observe some precautions. Improper
operation with disregard of precautions may result in infliction of harm to health of the user
and other people, as well as in infliction of damage to their property.
Use only the voltage specified on the rating plate of the heater.
ONLY connect the appliance to a properly installed socket-outlet with earth contact.
The heater should be connected to the electric mains equipped with an automatic circuit
breaker.
The unit must be handled with care, and avoid vibration or hitting.
WARNING: FIRE RISK EXISTS IF THE HEATER IS COVERED BY OR POSITIONED
CLOSE TO CURTAINS OR OTHER COMBUSTIBLE MATERIALS.
Do not use the appliance areas where gasoline, paint, explosives or other flammable
liquids are used or stored.
Do not use the appliance in a building site, green house, barn or in animal stables.
Do not use the appliance as a sauna heater.
Do not use this unit in the place of animal propagating and rising.
WARNING: Do not touch the radiating plate. Temperature of radiating boards during
operation of the heater may reach 380 °C. To avoid burns, do not touch the appliance
surface by hand and other body parts. It is also necessary to avoid touching the heater
whilst the appliance is switched on, as severe burns may result. The appliance can take
up to 1 hour to cool down after switching it off.
Do not place any items of clothing, hand towels or similar over the heater to dry. Risk of
overheating and fire hazard.
Do not leave the heater unattended whilst in use.
Do not use this heater on a wet surface, or where it can fall or be pushed into water.
Do not reach for an appliance that has fallen into water. Switch off at supply and unplug
immediately.
If the supply cord is damaged, it must be replaced by a licensed electrician.
If the heater is defective, it must be returned to the place of purchase.
Do not operate appliance with wet hands.
Use this appliance only as described in this manual. Any other use is not recommended
by the manufacturer and may cause fire, electric shock or injury.
Do not use abrasive cleaning products on this appliance. If the body becomes dirty, wipe
off dust with a cloth, and the radiating boards should be wiped in cold condition with a
damp soft cloth. Always remove plug from the mains supply before cleaning.
The heater must be installed at least 2.2 m above the floor.
The heater must not be located immediately below a socket-outlet. Socket-outlet should
not be located at the back of the heater. They should be located outside the physical
footprint of the units to minimize heat build-up behind the heater.
Page | 4
The installation must be equipped with a standard electrical power point with a break
contact distance of at least 3mm. The standard power point must be installed by a
licensed electrician.
If the heater is to be mounted on an incline (eg. Sloping or angled ceiling), ensure the
electrical connection is located at that lowest point of the heater.
Do not connect the appliance to the mains source until it has been installed in its final
location and adjusted to the position it will be used in.
Do not operate with the cord coiled up as this could cause a buildup of heat, which could
pose a hazard.
The use of an extension cord with this appliance is not recommended.
Do not allow cord to come in contact with heated surfaces during operation.
Do not run cord under carpeting, throw rugs or runners etc. Arrange cord away from areas
where it is likely to be tripped over.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance
The appliance is only intended for the purpose described in user manual.
Do not use appliance or any part of the appliance out of the intended use to avoid risk.
The use of attachments which are not recommended or sold by the appliance
manufacturer may cause a risk of injury to persons
CAUTION —some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
Install and operate the heater in a strictly horizontal position on the wall or ceiling surface.
The thermal resistance of the wall or ceiling material should be at least 80 °C.
WARNING: This heater is not equipped with a device to control the room temperature.
This heater is to be used in open, alfresco environment or large areas with high ceilings.
The heater must not be within reach from the floor, as severe burns may occur due to high
surface temperatures. Do not use this heater in small rooms or where the room or area is
occupied by persons not capable of leaving the room on their own, persons who are
unable to operate the heater safely and with the guidelines of the use manual, unless
constant supervision is provided.
Page | 5
MAIN FEATURES
①heater radiant surface
②heater operation indicators
③brackets for wall mounting
④power cords and plug
TECHNICAL SPECIFICATIONS
MODEL NAME
EOHA24R
Voltage
240V~ 50Hz
Rated power (W)
2400
Ideal Mounting height (M)
2.2 meters
Electric protection class
I
Water splash proof rate
IP65
The length of power cable(mm)
1050
Unit size- L*W*H(mm)
1505*177*60
Page | 6
HEATING AREA
The radiator panel heater produces radiant heat which heats objects rather than
the air. Therefore, it is imperative that objects to be heated (i.e. People), are within
the direct radiant footprint of the heater.
The below diagrams show the approximate heating area based on an outdoor
enclosed environment. And the diagram shows that the maximum heat output is
found directly under the heater, and the temperature decreases as the user move
away from the heater.
Outdoor enclosed area (m2)
Page | 7
BEFORE OPERATION
WARNING! Slight crackles may be heard during the heating or cooling period. This
is normal operational noise.
NOTE:
Discoloration of paint on the heater body wall directed to the ceiling during
operation is not a defect. Changing of color for heating plates is not defect.
After switching on the appliance for the first time and following extended
periods on non-use, the appliance may expel a slight odor for a short time. It
will not affect the use of the heater.
To exclude unpleasant burnt odor, it is recommended to keep the heater clean
preventing accumulation of dust on it
The distance between the heater and the remote control should be less than 3
metre, and the remote control must be directly point to the receiver on the
front panel during the operation.
Page | 8
HEATER COMPONENTS
REMOTE RECEIVER
HEAT STATUS
LAMP
TIMER LAMPS
Page | 9
OPERATION INSTRUCTIONS
1. Plug in the device, and press the power switch to the position of I : ON, the
device will sound 1 beep and the heat status lamp will turn blue. The device is
now in standby mode and won’t emit any heat.
2. Point the remote control directly to the receiver, press the “ON” button, the
device will sound 1 beep and the heat lamp will turn red. The device will start
to heat in high power mode (100% the rated power)
Press the “OFF” button again, the device will sound 1 beep and the heat status
lamp will turn blue. The device will stop heating and will stay in stand-by mode.
Page | 10
3. When the device is in heating mode or in stand-by mode, Point the remote
control directly to the receiver and press the button “low”, the device will sound
1 beep and the device will start to heat in lower power mode (33% of the rated
power). The heat status lamp will turn BLUE.
4. When the device is in heating mode or in stand-by mode, Point the remote
control directly to the receiver and press the button of “Med”, the device will
sound 1 beep and the device will start to heat in medium power mode (66% of
the total rated power). The heat status lamp will turn Green.
5. When the device is in heating mode or in stand-by mode, Point the remote
control directly to the receiver and press the button “High”, the device will
sound 1 beep and the device will start to heat high power mode (100% of the
total rated power). The heat status lamp will turn Red.
Indice
Altri manuali Excelair Stufa
Manuali Stufa popolari di altre marche
Empire Heating Systems
Empire Heating Systems WCC65 Manuale utente
Wetekom
Wetekom 92 86 43 Manuale utente
Desa
Desa SPC170-F Manuale utente
Watlow
Watlow Watrod Electric Tubular Heaters Manuale utente
Haverland
Haverland ECO-DRY GPS Series Manuale elenco delle parti
Stelpro
Stelpro ASILVC2060 Series Manuale utente