Exhausto EXcon HMI Touch Manuale utente
1
© 2018 OJ Electronics A/S
EXcon HMI Touch
EXcon HMI Touch
• English
• Deutsch
• Français
• Svenska
• Norsk
• Dansk
INSTRUCTIONS
67713A 11/18 (JRK)
© 2018 OJ Electronics A/S
3005584-2018-10-31
© 2018 OJ Electronics A/S
2© 2018 OJ Electronics A/S
INSTRUCTIONS
English.................................................................................. 3
Deutsch .............................................................................. 15
Français .............................................................................. 28
Svenska.............................................................................. 41
Norsk.................................................................................. 53
Dansk ................................................................................. 65
ILLUSTRATIONS
Pages.................................................................................. 77
3
© 2018 OJ Electronics A/S
EXcon HMI Touch
LIST OF FIGURES
Fig. 1: Installation on flat surface
Fig. 2: Removing the front cover
Fig. 3: Removing the back cover
Fig. 4: Dimensioned drawing to facilitate installation in wall box or
panel front
Fig. 5: Connecting Modbus via the RJ12 6P4C port
Fig. 6: Connecting Modbus via the screw terminals
INTRODUCTION
EXcon HMI Touch is a touchscreen panel with user-friendly graphi-
cal user interface specially developed for controlling ventilation
systems. The panel communicates with the Excon system via a
Modbus interface, ensuring easy installation.
PRODUCT PROGRAMME
Product Type
EXcon HMI Touch 3.5” touchscreen panel
OPERATION
If the screen saver is active, sim-
ply touch the screen once to open
the home screen.
This screen provides access to
elementary functions such as fan
speed, temperature and setup.
The time and day of the week
are shown in the top line of the
screen. Below these, an alarm
bell is visible if an alarm has been
activated. The house in the mid-
dle section of the screen provides
access to a simple overview of
temperatures, air volumes and
filter pressures. The temperature
English
4© 2018 OJ Electronics A/S
shown to the right of the house is the temperature setpoint. The
icons shown in the lower part of the screen can be changed and
may therefore dier from those shown in these instructions.
FAN SPEED
To set fan speed, press the fan in
the lower part of the home screen.
You can choose between five
predefined fan speeds. O, Auto,
Low, High and Service Stop. If you
choose Auto, EXcon HMI Touch
will follow a predefined program.
If you choose Low, the prede-
fined program is overridden and
the fan operates at low speed. If
you choose High, the predefined
program is overridden and the
fan operates at high speed. If you
choose O, the fan comes to a
complete standstill until fan speed
is again changed. If you choose
Service Stop, the system shuts down and can only be restarted
locally from the control panel.
TEMPERATURE
To change the temperature
setpoint for the selected control
mode, press the temperature on
the panel's home screen. Change
the temperature using the arrows
and confirm with the green button.
EXcon HMI Touch English
© 2018 OJ Electronics A/S 5
SETTINGS
EXcon HMI Touch is used together with an EXcon Master, and all
communication is via the master. Some settings can be made via
the menu icon in the upper right corner of the home screen.
Begin by pressing the menu icon in the upper right corner of the
home screen.
The following screen is then
displayed:
Home
Press this icon to return to the home screen.
Communication
Here you can configure LAN set-
tings such as static/dynamic IP
and associated addresses.
EXcon HMI Touch English
6© 2018 OJ Electronics A/S
Weekly program
Here you can enter times and
modes for the built-in 7-day clock.
Alarms
Here you can view active alarms
and an alarm log. In case of an
alarm, this screen can also be ac-
cessed via the bell icon on the
home screen.
EXcon HMI Touch English
© 2018 OJ Electronics A/S 7
Extended operation
If a dierent pattern of operation
is required for a short period of
time, the weekly program can be
overridden. The override period
can last up to a week at most.
Once the period has elapsed, the
system returns to standard clock-
controlled operation.
Unit components
Here you can make general set-
tings for the various components
that are installed.
Software update
Here you can check if an SD card inserted into the EXcon contains
a new software version.
EXcon HMI Touch English
8© 2018 OJ Electronics A/S
Settings
The following can be set/viewed:
• Language
• Time & date
• Locking of fan speed during
adjustment.
• Setting of fan speed in case of
fire/smoke extraction
• Setting of screen saver
• Restoration of factory settings
• Setting up the lower part of the
screen
• Software version
Language
Here you can choose the language
to be used on the screen.
EXcon HMI Touch English
© 2018 OJ Electronics A/S 9
Time & date
Here you can set the time and date
for the system.
Adjustment
Here you can lock fan speed
during system adjustment. Once
the required air volume has been
reached, the fan is locked at its
current speed. This gives the in-
staller the opportunity to adjust the
system, ensuring the right amount
of air in the individual rooms with-
out interference from ventilation
system regulation.
EXcon HMI Touch English
10 © 2018 OJ Electronics A/S
Fire
Here you can set the required fan
speed in case of fire/smoke.
Screen saver
Here you can set the screen saver
timeout period.
EXcon HMI Touch English
Indice
Lingue:
Altri manuali Exhausto Pannello touch
