Exsys EX-3512 Manuale utente

Indice

Altri manuali Exsys Scheda PCI

Manuali Scheda PCI popolari di altre marche

ERMA

ERMA SSI 1417 Manuale utente

SIIG

SIIG CyberSerial Dual PCI Istruzioni per il montaggio

Moxa Technologies

Moxa Technologies CP-102E Manuale utente

I-Bus

I-Bus IBC2602 Manuale utente

Chelsio Communications

Chelsio Communications T5 Series Manuale utente

Conrad Electronic

Conrad Electronic 97 46 71 Manuale utente

Micro Innovations

Micro Innovations USB650A Manuale utente

KTI Networks

KTI Networks KF-310 Manuale utente

Asus

Asus SpaceLink WL230 Manuale utente

SIIG

SIIG SC2475 Manuale utente

TRENDnet

TRENDnet TEW-703PI Manuale utente

Belkin

Belkin F5D7000F Manuale utente

Pericom

Pericom PI7C7100 Manuale utente

ADLINK Technology

ADLINK Technology cPCI-3548 Manuale utente

Digium

Digium TE200 Series Manuale utente

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuale utente

Western Digital

Western Digital FireWire PCI Adapter Manuale utente

Pyle

Pyle Gamelink PLINK1 Manuale utente

1

Thank you for purchasing this 2-Port SATA3 RAID PCI PCIe Card. It is

designed to support up to 2 SATA3 ports in RAID 0 and RAID 1 modes.

It supports SATA3 hard drives with up to 6.0Gbps data rate. It is an

ideal solution to add new external SATA3 drives for your system.

Features:

✓Supports 1-lane 5.0Gb/s PCI Express Data Transfer Rate

✓Built-in 2 eSATA3 Ports

✓Supports RAID 0 and RAID 1 for the 2 SATA3 Ports

✓Supports Windows based RAID GUI

✓Supports SATA3 transfer rate up to 6.0Gb/s (600Mbytes/sec)

✓Supports RAID 1 Rebuild by BIOS Setup Utility

✓Supports Windows 2000, XP, Vista and Win 7

1. Power down the computer, remove the computer cover.

EX-3512

2-Port eSATA3 RAID PCIe Card

1. Introduction

2. Board Layout

3. Hardware Installation

External

eSATA Port 1

External LEDs

External

eSATA Port 0

2-Port eSATA3 RAID PCIe Card

2

2. Choose an unused PCI Express bus slot, unscrew and remove the slot

cover.

3. Place the SATA3 RAID PCIe Card into the slot. Carefully press the board

into the slot until it seats firmly.

4. Secure the SATA3 RAID PCIe Card with the slot cover screw.

5. Install the SATA cables from the SATA connectors to your SATA devices.

6. Carefully reinstall the computer cover. Insert and tighten the computer

cover screws.

7. Power up the PC and observe the monitor. The BIOS lists all Serial ATA

devices attached to the SATA3 RAID PCIe Card. For example:

Marvell 88SE91xx Adapter –BIOS Version x.x.x.xxxx

PCIe x1 5.0Gbps

Mode: CPU AHCI

Virtual Disk

No Virtual Disk!

Physical Disk

[ID] [DISK Name] [Size] [Speed]

0 SATA ST32000641AS 1.83TB 6.0G

8 SATA ST32000641AS 1.83TB 6.0G

Press <Ctrl>+<M> to enter BIOS Setup or <Space> to continue

If the information displayed on your monitor is correct (the installed

devices are listed with the correct device name, etc.), congratulations!

You have successfully installed the SATA3 RAID PCIe Card in your

computer. If you want to configure your RAID drives, press and hold the 2

keys, Ctrl and M, to enter the BIOS Setup for this card. You can configure

the SATA RAID modes in the BIOS Setup.

Turn on your computer and press <Ctrl> and <M> keys to enter BIOS

Setup during the POST (Power-On Self-Test).

4. Configuring a SATA Disk Array

2-Port SATA3 RAID PCIe Card

3

4.1 Create a Disk Array:

Under Free Physical Disks, use the <Space> key to select the hard

drives to be included in the RAID array. The selected hard drive will be

marked with an asterisk (*). After selecting the hard drives, press

<Enter> to proceed.

To further configure the disk array, use the up or down arrow key to

move the selection bar to select an item in the right block of the

screen and press <Enter>. Set the required items in sequence and

press <Enter> after each step:

1. RAID Level: Select a RAID level. Options include RAID 0 (Stripe)

and RAID 1 (Mirror).

2-Port eSATA3 RAID PCIe Card

4

2. Stripe Size: Select the stripe block size. Options include 32 KB and

64 KB.

3. Gigabyte Rounding: Select whether to permit the installation of a

replacement drive that is smaller than the failed drive when

performing a RAID 1 rebuild. Options include None, 1G, and 10G.

4. Quick Init: Select whether to quickly erase old data on the hard

drives when creating the array.

5. VD Name: Enter an array name with 1~10 letters (letters cannot

be special characters).

6. Next: After completing the settings above, move to Next and

press <Enter> to begin creating the array. When prompted to

confirm whether to create this array, press <Y> to confirm or <N>

to cancel.

7. When completed, you can see the new array under

Topology\Virtual Disks.

8. Save the Settings and Exit. After you complete the RAID

configuration and before you exit the configuration screen, be

sure to press <F10> in the main screen. Press <Y> to confirm or <N>

to cancel.

9. Now, you may proceed to create the SATA driver diskette (for

AHCI mode) and the installation of the SATA driver and operating

system

4.2 Delete the Disk Array:

To deleted the existing array, select the array on the main menu

(example: VD 0: New_VD) and press <Enter> to display the Delete

option. Press <Enter>. When prompted, press <Y> to confirm or <N> to

cancel.

With the Marvell RAID utility (RAID GUI), you can setup an disk array or

view the current array status in the operating system. To install the

utility, insert the supplied driver CD (folders as the following picture).

5. Installing RAID Drivers and GUI

2-Port SATA3 RAID PCIe Card

5

Please follow the following steps:

1. Run the driver installer (drvSetup.exe) in the folder

\SATA3\88SE9128\Drivers to install the RAID drivers

2. Reboot the system to let the drivers take effect.

3. Run the RAID GUI installer

(\SATA3\88SE9128\Utility\MRUSetup.exe) to install the RAID Utility.

Note: After the installation, you must login the utility with the same

account name and password that you use to login the operating

system. If you did not set the account password before, click Login to

enter the Marvell RAID Utility directly.