Extron electronics XPA 1002 Manuale utente

XTRA™Half-Rack Series

Audio Power Ampliers • Setup Guide

WARNING: May cause serious injury. Installation and service must be performed by authorized personnel only. These

products must be used with UL approved, grounded, electrical boxes.

This guide provides startup instructions for an experienced installer to set up and operate the XPA 1002 or XPA 2001 Series

audio power ampliﬁer. All references are to the XTRA™Half-Rack Series User Guide which can be found on the Extron

website.

Step 1

Be sure that power to the ampliﬁer is turned off ﬁrst.

NOTE: Adjust the audio level to =(full attenuation) prior to the ampliﬁer being powered back up in step 5(see

“Rear Panel Features and Operation” in the User Guide).

Turn off all other equipment and disconnect the power cords. Verify that the ampliﬁer is disconnected from the power

source before proceeding.

Step 2

For diagrams of typical application examples, see “Application Examples” in the User Guide. For further mounting

instructions, see “Mounting the XPA 1002 and XPA 2001” in the User Guide.

Step 3

NOTE: Control signal ground pins may be labeled as or “G”. Audio ground pins may be labeled as or .

The wiring and function are the same, whichever way your product is labeled.

Wire the source output to the ampliﬁer input 3.5 mm captive screw connectors as shown in the following illustration (see

“Rear Panel Features and Operation” in the User Guide).

NOTE: The output power of the XPA 1002 can be effectively doubled by using only one input channel and bridging the

output. The XPA 1002 outputs 200 watts @ 8 ohms in bridged mode (see “Bridged Mono Output” in the

User Guide for wiring instructions when bridging the XPA 1002).

Do not tin the wires!

XPA 1002

Unbalanced Mono Input

Tip

Sleeve

XPA 1002

Balanced Mono Input

Tip

Ring

Sleeve

Unbalanced Stereo Input

Tip

Sleeve

Tip

Balanced Stereo Input

Tip

Ring

Tip

Ring

Sleeves

NOTE: For mono input on the XPA 2001, only the left channel needs to be wired; no jumpering to the right channel is

needed. The left and right inputs of the XPA 2001 are summed internally to mono.

Step 4

Wire the speakers to the output connector of the ampliﬁer using the included 4-pole (XPA

1002) or 2-pole (XPA 2001-70V and XPA 2001-100V) captive screw plug as shown to the

right. See “Rear Panel Features and Operation” in the User Guide.

Step 5

ATTENTION: The ampliﬁer must be powered on last.

Reconnect all power cords and switch on all other equipment before powering on the power ampliﬁer. The front panel

power LED of the ampliﬁer lights green.

XPA 2001-70V

XPA 2001-100V

XPA 1002

68-1351-50 Rev. B

06 12

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+4000.EXTRON

+4000.398766

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron

Middle East

+971.4.2991800

+971.4.2991880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

Inside India Only

+91-80-3055.3777

+91 80 3055 3737 FAX

Step 6

Adjust the audio attenuation using the rear panel adjustment knobs as shown below. See “Rear Panel Features and

Operation” in the User Guide.

NOTE: On some models, this adjustment is referred to as “level”. The function is the same, whichever way your product

is labeled.

XPA 10 02 XPA 2001 Series

∞0

∞

ATTENUATION

∞

ATTENUATION

LEVEL

0 0

LEVEL

XPA 10 02 XPA 2001 Series

Step 7

On XPA 2001-70V and XPA 2001-100V models, use a Tweeker to toggle the high pass ﬁlter switch between

off (no ﬁltering) and 80 Hz (default). Setting the switch to 80 Hz prevents the saturation of speaker input

transformers by low frequency signals.

Step 8

Check the limiter/protect and signal LEDs located on the front and rear panels if problems are encountered.

See “Rear Panel Features and Operation” in the User Guide.

Step 9

The 3.5 mm 5-pin captive screw remote control port (shown to the right) is used to control

volume and standby mode through contact closure. Standby mode turns off all output,

although the XPA is still receiving power.

See “Front Panel Features and Operation” in the User Guide for more information.

NOTE: The remote control port may be labeled one of two ways (see the images above). The wiring and function are

the same, whichever way your product is labeled.

STANDBY

10V

REMOTE

50mA

HPF

80 Hz

OFF

12345

STANDBY

VOL/MUTE

10V 50 mA

Altri manuali per XPA 1002

Questo manuale è adatto per i seguenti modelli

Altri manuali Extron electronics Amplificatore

Extron electronics

Extron electronics VersaTools MTP DA4 Manuale utente

Extron electronics

Extron electronics CVDA 6 MX Dual Manuale utente

Extron electronics

Extron electronics Two Output 13W3 Sun and SGI Distribution Amplifier 13W3... Manuale utente

Extron electronics

Extron electronics ADA 6 Component Manuale utente

Extron electronics

Extron electronics MPA 401-70V Manuale utente

Extron electronics

Extron electronics XPA Ultra Fx Series Manuale utente

Extron electronics

Extron electronics P/2 DA2xi MT Manuale utente

Extron electronics

Extron electronics VersaTools MDA 3 Series Manuale utente

Extron electronics

Extron electronics SW HD 4K PLUS Series Manuale utente

Extron electronics

Extron electronics MPA 152 Manuale utente

Extron electronics

Extron electronics NetPA Ultra Series Manuale utente

Extron electronics

Extron electronics MDA 4V EQ Manuale utente

Extron electronics

Extron electronics XTRA FULL RACK XPA 2002 Manuale utente

Extron electronics

Extron electronics DA2 RGBHV Manuale utente

Extron electronics

Extron electronics DVI DA2 Manuale utente

Extron electronics

Extron electronics DA6 RGBHV Manuale utente

Extron electronics

Extron electronics FOX DA8 Manuale utente

Extron electronics

Extron electronics SW2 VGA DA2 A Manuale utente

Extron electronics

Extron electronics NetPA U 2002 SB Manuale utente

Extron electronics

Extron electronics HPA 1001-70V Manuale utente

Extron electronics

Extron electronics XPA Ultra Series Manuale utente

Extron electronics

Extron electronics APP Manuale utente

Extron electronics

Extron electronics P/2 DA 2 WM/EC Manuale utente

Extron electronics

Extron electronics Extron P/2 DA2xi Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente