Extron electronics ACP 100 Manuale utente

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

ACP 100 • Setup Guide

The Extron ACP 100 Audio Control Panel is a fully congurable control interface for use with any Extron ACP-enabled device.

Each ACP 100 includes two ACP ports, which support both power and communication between the host device and the

ACP100. Up to eight ACP panels can be used per host device for more demanding control needs.

Front Panel Features

Extron

MIC

SOURCE

PROGRAM

VOLUME

MUTE

SOURCE

MIC PROGRAM

SOURCE

MUTE

SOURCE

RESET

ACP 100 Front Panel with Plastic

Faceplate

ACP 100 Front Panel without

Plastic Faceplate

EEEE

CCCC

BBB

AAA

DDDF

FFF

Figure 1. ACP 100 Front Panel

Rear Panel Features

PWR LOAD = 0.5W

123456

BUS ID

123456

PWR LOAD = 0.5W

ERROR

STATUS

LINK

COM

ERROR

STAT U S

LINK

COM

ERROR

ACP

S+S

+V G

S+S

ACP 100 Rear Panel

CCCC

BBB

AAA

Figure 2. ACP 100 Rear Panel

Planning the System and Installation

When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see

the ACP 100 product page at www.extron.com for more information about the ACP 100).

APlastic Faceplate

BFunction Buttons 1 and 2

CFunction Buttons 3-6

DVolume LEDs and Knob

EMounting Holes (4)

FReset Button

ABus ID DIP Switches

BACP Ports (2)

CACP Status LEDs

ACP 100 • Setup Guide (Continued)

Installation

Step 1: Get Ready

Use the following checklist to prepare for the installation:

Download and install the latest version of software, rmware, and device drivers needed to congure the host device and

congure the connected ACP products (see the host device user guide, available on www.extron.com, for details on

software and drivers).

Obtain cables, mounting hardware, and any other supplies required for ACP 100 installation.

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP 100 into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le ACP 100 dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• If the ACP 100 will be installed into fine furniture, it is best to hire a licensed, bonded craftsperson to cut the access hole

and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le ACP 100 dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et qualifié

pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 100 must

be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the

ACP100.

Americans with Disabilities ACT (ADA) Compliance

When planning where to install these devices, consider factors affecting accessibility of the button panel such as height

from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections

307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 ADA Standards for Accessible Design available at

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external

wall boxes (EWBs), and surface or tabletop mounting boxes for use with the ACP button

panels. The ACP 100 is a US 2-gang size device.

Step 3: Replace Plastic Faceplate, Button Labels, or

Knob

The plastic faceplate button labels can be replaced. Some

button labels ship with the unit. Customized labels can be

created and printed using Extron Button Label Generator

software from www.extron.com.

To change a plastic faceplate or translucent button label:

1. The plastic faceplate is secured with four magnetic

catches on the underside of the plastic faceplate.

Remove the plastic faceplate by holding the body of

the unit with one hand, gripping the sides of the plastic

faceplate with the other hand, then pulling the plastic

faceplate away from the unit.

2. Gently separate the button lens cap from its white

diffuser. Insert the end of the provided Extron removal (pry) tool into the corner notch

and gently twist the tool (see 1in the image to the right).

TEXT

Separate the

two-piece button

her

e at the corner.

Dif

fuser

Base

Insert

button label.

Button

Lens Cap

Removal

(Pry) Tool

3. Remove the label insert from the button lens cap.

4. Select one of the button labels from the printed label sheet included with the device. Remove the label from its backing and

remove the clear protective lm from the front of the label.

5. Insert the button label into the button lens cap (see 2in the image on the previous page).

6. Align the button lens cap with the white diffuser and the panel opening, then press the button lens cap into place on the

button.

7. Attach the plastic faceplate to the ACP 100. Align the openings of the faceplate with the buttons and knob and place the

plastic faceplate against the unit. The four magnetic catches fasten the faceplate onto the unit.

To replace the rotary knob:

1. Remove the plastic faceplate as described at the bottom of the previous page.

2. Firmly grasp the knob and pull it away from the ACP 100.

3. Align the ridge inside the new knob with the channel on the knob control and allow the magnet in the knob to snap into place.

4. Reattach the plastic faceplate to the unit as described in step 7 above.

Step 4: Set Bus ID Addresses

PWR LOAD = 0.5W

123456

BUS ID

123456

ERROR

STATUS

LINK

COM

ERROR

ACP

S+S

+V G

S+S

+V G

S+S

V+

S G

–

010010

123456

000001

123456

18Unit address

DIP switches

Binary address

ACP port on a

DMP Plus, or on

another ACP

endpoint

ACP Ports

• Connect up to eight (8) ACP endpoint devices per DMP Plus.

• Wire the connectors the same at both ends.

• These ports are identical. You can connect devices

interchangeablly to either port.

• Do not exceed a total of 1000 feet (305meters) of cable for

connections between the DMP Plus and all of the ACP

panels.

• Power is provided by the IPCP Pro, a PS 1220EB power

inserter, or an Extron 12 VDC power supply.

Bus ID Address DIP Switches

• Use these DIP switches to set the six-bit, binary

bus address for the ACP 100.

• Each ACP connected to the same DMP Plus

must have a unique address.

• Switch 1 (on the left) is the highest value (32, the

the most signicant bit [labeled “MSB”]).

• Switch 6 (on the right) is the lowest (1, the least

signicant bit [labeled “LSB”]).

• Up = on = 1, Down = off = 0

Examples:

Figure 3. ACP 100 Rear Panel Bus ID

ﬁgure 3

Set the bus identication (ID) DIP switches for the ACP 100 and any other

ACP panels being connected to the system. Each ACP device must have

a unique bus ID. If multiple ACP panels have the same bus ID, address

conicts may cause one or more of the panels to not be recognized in

DSP Congurator or by the host device. Up to eight ACP devices can be

connected in the same system.

Each ACP device in a system must have a unique six-digit binary bus ID.

ACP bus IDs are set by using the DIP switch assembly on the rear panel of

the ACP 100.

Switch 1 on the left sets the most signicant bit (highest number, 32) while

switch 6 on the right sets the least signicant bit (the lowest number, 1).

See the example addresses in the table to the right.

Slide

1 2 3456

BUS ID

Example Addresses

Bus ID

(Decimal)

Binary

Address

DIP Switch

Setting

0 000000*

1 2 3456

1 000001

1 2 3456

2 000010

1 2 3456

3 000011

1 2 3456

4 000100

1 2 3456

5 000101

1 2 3456

6 000110

1 2 3456

7 000111

1 2 3456

8 001000

1 2 3456

*Address 000000 is reserved for the control processor and cannot be used by any ACP devices.

ACP 100 • Setup Guide (Continued)

Step 5: Cable All Devices

1. Connect the ACP panel to the host device.

2. Connect ACP panels to each other if multiple panels are being used in the control system (see gure 4 below for correct

wiring).

NOTES:

• Wire both ends of each ACP cable the same. Connectors are interchangeable between the host device and ACP

device.

• Do NOT power an ACP panel from more than one power source.

3. Apply power to the host device after correctly cabling all devices.

Cabling

Attach cables using the diagram below as a guide. Wiring is the same for all ACP models. Connect a 4-pole captive screw

connector to each end of the cable, wiring both ends the same. In most cases, the ACP devices are powered by the DMPPlus

series device. Power is carried on the V+ pin of the ACP 100 and other ACP devices.

Extron STP20-2/1000 or STP20-2P/100 cable is recommended for ACP device connections.

Ground

+Signal

Signal

+12 VDC

Black

and

Drains

Green

White

Red

S+S

Drain Wires

Basic ACP Connector Wiring

Figure 4. Basic ACP Connector Wiring

ACP devices that are relatively far from the host device can be connected to an optional Extron PS 1220EB eBUS power

inserter or an Extron 12 VDC desktop power supply as shown in the diagrams below and on the next page (see the ACP 100

Speciﬁcations at www.extron.com for cable length to determine if additional power is recommended).

ATTENTION:

• Always use a power supply supplied or specified by Extron. Use of an unauthorized power supply voids all regulatory

compliance certification and may cause damage to the supply and the unit.

• Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une source d’alimentation non autorisée

annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que l’unité.

• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked

“Class2” or “LPS” and rated output 12VDC, minimum 1.0A.

• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit être alimenté par une source

d’alimentation certifiée UL de classe 2 ou LPS et paramétré à 12VDC et 1,0A minimum.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération

ou dans les cavités murales.

• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA70,

article725 and the Canadian Electrical Code part1, section16. The power supply shall not be permanently fixed to

building structure or similar structure.

• Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/

NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas être

fixée de façon permanente à une structure de bâtiment ou à une structure similaire.

eBUS 24 WATTS MAX

100-240V 50-60Hz

0.6A MAX

V+

S G

–

V+

S G

–

S+

V+

S G

–

S+

V+

S G

–

V+

S G

–

S+

V+

S G

–

ACP port on

an ACP

endpoint

device

V+

S G

–

LAN

DMP 128 Plus C

RxTx G

RS-232

+S+V -S G

5 6 7 8

1 2 34

OUTPUTS

DMP EXP

ACP

REMOTE

USB AUDIO RESET

DMP 128 Plus

S+S

Tie drain wires

to ground.

S+S

Ground

+Signal

Signal

+12 VDC

S+S

Power Input

(100-240 VAC,

50-60 Hz)

PS 1220EB

ATTENTION: Do NOT connect the power

pin to any device that is already powered

by the DMP Plus control processor or by

an additional power supply.

3/16" (5 mm) Max.

ACP

Panel(s)

ACP Connections

• Connect up to ve (5) ACP

endpoint devices to the PS 1220EB.

• Wire the connectors the same at

both ends.

• All ports are identical and

interchangeable.

Figure 5. Cabling ACP Devices with a PS 1220EB Power Inserter

PWR LOAD = 0.5W

123456

BUS ID

123456

ERROR

STATUS

LINK

COM

ERROR

ACP

S+S

+V G

S+S

ACP port

on a host

DMP Plus

V+

S G

–

ACP port

on an ACP

100 or other

ACP device

V+

S G

–

Tie drain wires to ground.

G-S+S

Ground

+Signal

Signal

+12 VDC

– Return

+12 VDC input

Ridged

Smooth

External Power Supply

(12 VDC, 1.5 A max.)

Ground all

Devices

ACP 100

Rear Panel

NOTE:

Check the polarity of the power

supply before connecting it to the ACP.

3/16" (5 mm) Max.

Power Input,

External Power Supply (optional)

• Connect to an Extron 12 VDC power

supply.

NOTE: Check the polarity of the power supply before connecting it to the ACP.

Figure 6. Cabling ACP Panels with an Extron 12 VDC Power Supply

ACP 100 • Setup Guide (Continued)

Step 6: Conﬁgure the System

NOTE: For complete information on creating conguration les and operating DSP Congurator, see the host device user

guide and the DSP Conﬁgurator Help le.

1. Create a new host device conguration le in DSP Congurator and create all groups, presets, and macros to be controlled

by the ACP device.

2. Select Tools>Configure ACPs in DSP Congurator and congure the ACP button actions and panel IDs.

3. Connect to the host device in Live mode with a TCP/IP connection and push the conguration le to the device.

Step 7: Test and Troubleshoot

1. Verify the ACP bus ID DIP switches are set to the desired address on each unit and that there are no bus ID address conicts

in the system.

The ACP 100 may have a single monochrome LED (green) or three separate LEDs (green, amber, or red). The LED (or LEDs)

are a diagnostic tool showing the device status:

Device Status Single LED (green) Three LEDs

No power, ACP cable broken. Off Off

Device is receiving power and communicating correctly

with the DMP Plus.

Lights solidly Green

Device is receiving power but cannot communicate with

the DMP Plus

Slow blink Amber

Device is receiving power and communicating with the

DMP Plus but there is an address conflict.

Fast blink Red

2. Verify cables to and from the ACP devices are wired the same at each end.

3. Test the system:

a. Press the ACP device buttons and ensure the buttons light as expected and that the appropriate control actions are

triggered. Commands can be veried using DSP Congurator. DataViewer can also be used for command verication if

responses are congured.

b. Ensure the audio levels respond correctly to the volume and mute buttons.

4. Make adjustments to wiring, bus ID addresses, and system conguration as needed. Remember that the rear panel ports

and DIP switches are not accessible after the ACP is mounted. If needed, push a revised conguration to the ACP device

through the host device using DSP Congurator.

If you have questions during installation and setup, call the Extron S3 Sales and Technical Support Hotline or the Extron S3

Control Systems Support Hotline (1.800.633.9877).

Step 8: Mounting the ACP 100

Prior to mounting:

1. Feed all device cables through the wall or furniture and, if applicable, through the plastic spacer.

NOTE: If the unit is not installed in a mud ring, the plastic spacer must be installed. The spacer positions the unit to allow

the magnetic catches on the plastic faceplate to attach properly and securely.

2. Ensure the cables are connected to the ACP 100 rear panel.

Mount the ACP 100 as follows:

1. Insert the cabled ACP 100 into the mud ring or junction box within the wall or furniture, aligning the mounting holes in the

ACP 100 with those in the box or mud ring.

2. Secure the ACP 100 in the junction box, wall or surface mounting box, or mud ring as follows (see 1in the gures below).

a. Insert the included screws through the oval slots at the top and bottom of the ACP 100 metal mounting plate, through

the plastic spacer (if not using a mud ring), and into the corresponding threaded holes in the box or mud ring.

b. Using a Phillips screwdriver, gently tighten the screws until snug.

3. Attach the plastic faceplate to the ACP 100. Align the plastic faceplate openings with the buttons, knob, and LEDs and place

the plastic faceplate against the metal mounting plate (see 2in the gures below). The magnetic catches fasten the plastic

faceplate onto the metal mounting plate.

RESET

SOURCE

MUTE

SOURCE

PROGRAM

MIC

SOURCE

Extron

VOLUME

Wall

Junction

Box

Plastic

Faceplate

Metal Mounting

Plate

Plastic Spacer

RESET

SOURCE

MUTE

SOURCE

PROGRAM

MIC

SOURCE

Extron

VOLUME

Metal Mounting

Plate

Wall Mounting

Bracket

(Mud Ring)

Plastic

Faceplate

Wall

Figure 7. Installing the ACP 100

in a Junction Box

Figure 8. Installing the ACP 100

in a Mud Ring

68-3065-50 Rev. B

07 19

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Indice

Altri manuali Extron electronics Pannello di controllo

Extron electronics

Extron electronics Decorator-Style Series Manuale utente

Extron electronics

Extron electronics MLC Plus 84 EU Manuale utente

Extron electronics

Extron electronics eBUS Button Panel EU Series Manuale utente

Extron electronics

Extron electronics RCP 2000 Manuale utente

Extron electronics

Extron electronics MKP 2000 Manuale utente

Extron electronics

Extron electronics MKP 2000 Manuale utente

Extron electronics

Extron electronics eBUS Button Panel Decorator-Style Series Manuale utente

Extron electronics

Extron electronics TLP Pro x25M Series Manuale utente

Extron electronics

Extron electronics ACP 105 EU/MK Manuale utente

Extron electronics

Extron electronics TouchLink Pro Series Manuale utente

Extron electronics

Extron electronics RCP 2000 Manuale utente

Extron electronics

Extron electronics IP Link Pro NBP 50 Manuale utente

Extron electronics

Extron electronics SCP 150L Manuale utente

Extron electronics

Extron electronics ACP 106 D Manuale utente

Extron electronics

Extron electronics ACP 105 D Manuale utente

Extron electronics

Extron electronics RCP 101 D Manuale utente

Extron electronics

Extron electronics ACP 100 Manuale utente

Extron electronics

Extron electronics SCP 200 Manuale utente

Extron electronics

Extron electronics ACP VCI EU/MK Manuale utente

Extron electronics

Extron electronics MKP 2000 Manuale utente

Extron electronics

Extron electronics MLC 55 RS Manuale utente

Extron electronics

Extron electronics ACP VC1 EU/MK Manuale utente

Extron electronics

Extron electronics ECP 1000 Manuale utente

Extron electronics

Extron electronics TLP Pro 320C Manuale utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche