Extron electronics MEDIALINK MLC 206 Manuale utente

The Extron MediaLink™ Controller (MLC 206) provides infrared (IR) and RS‑232

remote control of a display device, contact closure control of items in a room, tally

outputs, and MediaLink Switcher control.

This guide provides instructions for an experienced installer to set up and operate

the MLC 206 MediaLink Controller.

When possible in the following pages, line drawings are used to clarify steps

discussed in the text.

Setup Guide — MLC 206

68-601-50

Rev. A

11 09

MLC 206 typical application diagram

VCR

Extron

Switcher

DVD Laptop

Extron MLC 206

Lighting

Control

Switcher

Control

Screen

Control

Projector

Control

100-240V 0.2A 50/60 Hz

AUDIO OUT

INPUT 1

VIDEOR-Y

YUV

R-Y

B-Y

VIDEO

S-VIDEO

INPUT 2

VIDEO

R-Y

INPUT 3

B-Y

INPUT 4

INPUT 5

RGB

RH/

AUX/MIX

EFFECTS

SEND

RETURN

COMM LINK

ABCDE

RS232

CONTACT CLOSURE

4 ohm

MONO AMPLIFIED OUTPUT

COMM8 ohm70V

Document

Camera

Extron

MLC 206

DISPLAY

POWER

VOLUME

MAX/

MIN

VCRDVDLaptop

MLC 206 Setup Guide, cont’d

Step 1 — Computer Connection

The MLC 206 must be connected to a PC in order to conﬁgure the controller. The

conﬁguration port, shown in the rear panel view below, is used for system control

and for loading conﬁguration and driver ﬁles into the MLC.

1. Connect a host computer to the MLC 206 Conﬁg port via the rear

panel 9‑pin HD female RS‑232 connector. Use a serial cable with

9‑pin D connectors.

A B C D E A B C

Display/Source Control

Extron Switcher Control

Relays IR/RCM

RS-232

D E A B C A BD

1A 1B 2A 2B 3A 3B

123456

Tally Out

MLS

/Power

33-644-01 A

07 01

Config

9-pin

D Connector

Host Desktop

Computer

RS-232

Configuration Port

2. Connect all control modules that will be used in the system.

N Control modules must be connected at this time so they can be conﬁgured

with the software. Connections for IR and serial control can be installed

after conﬁguration.

MLC 206

RCM

port

MLC IR-IRCM wiring_01-05.eps

A B C D

RCM

IRCM control

module(s)

A B C D E Control

module

connector

+12 VDC

Control signal (IRCM)

Ground ( ) B

MLC 206 to a control module

Total distance from

MLC: 150' (45.7 m) max.

MLC 206

Extron

DISPLAY

POWER

VOLUME

MAX

MIN

VCR DVD Laptop

MLC 206

IRCM-DV+

DVD & VCR CONTROL

PLAY NEXT/FWD PAUSE STOP

TUNER

PREV/REW

ENTER

TITLE MENU

TV/VCR

DVD VCR

3. To power the MLC, connect a 12 VDC power supply or an optional

MediaLink Switcher (MLS) to the MLS/Power port, and connect the power

supply or the switcher to a power source.

MediaLink Switcher

MLC/RS-232

A B

MLC 206 powered by a MediaLink Switcher

Connecting an MLC 206 to an external power supply

MLC 206

MLS/Power

port

MLC

MLS/Power

port

A B

MLS

Power

Ground ( )

+12 VDC input

0 A ground wire must be connected

between the MLC and MLS.

Ground ( )

+12VDC

Transmit (Tx)

BReceive (Rx)

A B

MLS

Power

Transmit (Tx)

Receive (Rx)

+12VDC

Ground ( )

Ground all devices

An external

power supply

(12 VDC, 1 A max.)

Step 2 — Software Installation

The MLC must be conﬁgured before it can send commands to the projector or other

devices. Install the MediaLink Control Program software on the host PC. To install

the software, run SETUP.EXE from the Extron‑provided disk. Follow the instructions

that appear on the screen.

N The software is also available at www.extron.com.

MLC 206 Setup Guide, cont’d

Step 3 — Setting up projector control

Device drivers allow the MLC 206 to control projectors and other source devices via

RS‑232 or IR.

N It is strongly recommended that an RS-232 control (ﬁlenameRS1.mll) ﬁle for

controlling a projector be used whenever possible.

To load a driver and conﬁgure the MLC 206:

1. Start the MediaLink Control Program.

The appearance of the screens varies depending on which

accessories (control modules and/or MediaLink Switcher)

are connected to the MLC, as shown in the following

pictures.

MLC 206 without accessories MLC 206 with an MLS switcher,

IRCM-DV+, and RCM-SC connected

2. Load a projector driver: select the third tab, Controller (MLC) Config, and

select the Load Extron Driver button, as shown in the following illustration.

Choose the appropriate projector driver (ﬁlename.mll) from the on‑screen

menu. If the projector brand and model are not listed, check the Extron Web

site to see if a new driver is available or enter user‑deﬁned RS‑232 strings. See

“Advanced Projector Conﬁg” in chapter 4 of the User’s Manual for details.

3. Conﬁgure the buttons. Use the

drop‑down box associated with each

button to select the command to be

issued or function to perform, as

shown at right.

Each conﬁgured button has a green or red dot on it.

N If a button has been previously conﬁgured, it will have a red (IR) or

green (RS-232) dot to indicate that an IR or RS-232 code has been associated

with it.

4. Choose a volume control option. Select Projector if

planning to use the projector display speakers or if using

the projector display as a preamp. Select Switcher (MLS)

when using an external switcher as an audio preamp or

ampliﬁer.

Step 4 — IR learning

If there are no drivers available, the MLC can learn IR commands to control

projectors or other devices. IR learning is required to conﬁgure control modules to

control devices such as DVD players.

1. Select the third tab, Controller (MLC) Config.

2. Click on the appropriate button on the control module or the MLC to learn IR

codes.

N If a button has been previously conﬁgured, it will have a red (IR) or

green (RS-232) dot to indicate that an IR or RS-232 code has been associated

with it.

MLC 206 Setup Guide, cont’d

4. Click on OK to begin the learning process.

During IR learning hold the device remote control 4 inches to 14 inches

(10 cm to 36 cm) away from and directly in front of the MLC’s IR pickup

device.

Aim the remote

control at the MLC’s

IR pickup devices,

press the remote’s

button, follow

on-screen prompts

MLC 206

Extron

MediaLink Controller

MLC 206

DISPLAY

POWER

VOLUME

MAX/

MIN

VCR DVD Laptop

1 2 3

4 5 6

7 8

4"–14"

(10–36 cm)

3. Click on the button labeled Learn IR to Button. A dialog box appears

indicating the button to which IR codes will be learned.

Once the IR commands have been successfully

learned, the button will be shown with a red dot

(shown at right) and the button/function may be

named.

5. Repeat steps 2 through 4 to set up additional buttons.

Step 5 — Completing the installation

1. Save the conﬁguration by selecting Save CONFIGURATION as..., and name it

appropriately.

2. Connect the MLC 206 to the projector for RS‑232 projector control.

a. Disconnect the power from the MLC (and the optional MediaLink Switcher,

if applicable) and from the projector.

b. Plug the 9‑pin D connector of the RS‑232 projector control cable (such as an

Extron UC 50’ cable) into the projector RS‑232 port. A cable adapter may be

required.

c. Connect the other end of the projector control cable to the MLC

Display/Source Control RS‑232 port. Wiring depends on the projector. See

the diagrams below and on page 8, and the pin assignments in the projector

user manual. Also see the display driver setup document available from

the download page of the Extron Web site.

N In most cases only the transmit (Tx), receive (Rx) and ground connections will

be needed. Wiring varies depending on the projector model.

A B C D E A B C

Relays IR/ RCM

RS-232

D E A B C A BD

1A 1B 2A 2B 3A 3B

123456

Tally Out

33-644-01 A

07 01

MLS/Power

Display/Source Control Extron Switcher Control

MLC RS-232 display ctrl wiring_112202.eps

Request to send (RTS)

Ground ( )

Transmit (Tx)

Receive (Rx)

Clear to send (CTS)

To the RS-232 port of

the display/projector

MLC 206 Setup Guide, cont’d

3. Install the IR Emitter(s) in the IR port as shown in the following illustration,

and attach the head of each IR Emitter to an IR‑controlled device (VCR,

DVD player, projector).

N Place the IR emitter directly over the IR pickup device of the equipment.

MLC-IR emitter_wiring_QS_112202.eps

A B C D E A B C

Display/Source Control

Extron Switcher Control

Relays IR/RCM

RS-232

D E A B C A BD

1A 1B 2A 2B 3A 3B

123456

Tally Out

MLS

/Power

33-644-01 A

07 01

Emitter

White striped wire only

Modulated IR

Ground

110 feet (33.5 m) maximum

0 Connect up to a maximum

of 4 IR Emitters

4. Install any optional accessories (IR Link, relays, tally out) that will be connected

to the MLC 206. Refer to chapter two of the MLC 206 User’s Manual and to the

accessory manual(s) for wiring diagrams and installation details.

5. Reconnect the power supply or optional MediaLink Switcher (MLS) to the

MLS/Power port and connect power to all controlled devices.

6. Verify the system operates correctly when selections and adjustments are made

at the front panel and/or from the User Mode section of the control software.

Adjust cabling or retry IR learning as needed.

7. Disconnect the host PC from the MLC 206, remove power from the MLC

(unplug the power supply or switcher), and label the inputs (see the

MLC 206 User’s Manual for details).

8. Mount the MLC and accessories into the wall or furniture, and restore power.

The UC cable pin assignments are shown in the following illustration.

Purple

Blue

Green

Yellow

Orange

Red

Brown

Grey

Black

Connector Shell

Pin #Color

UC Cable

Shield

UC 50', 100' Cable Color Codes

To the

projector

To the

MLC 206

Extron USA - West

Headquarters

+800.6 33.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.6 33.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.44 00

+65.6383.46 64 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.156 8

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FA X

Extron Middle East

+971.4.2991800

+971.4.2991880 FA X

Altri manuali per MEDIALINK MLC 206

Indice

Altri manuali Extron electronics Controllori

Extron electronics

Extron electronics RAC 104 Manuale utente

Extron electronics

Extron electronics MediaLink MLC Plus 50 Manuale utente

Extron electronics

Extron electronics MediaLink MLC Plus 84 Series Manuale utente

Extron electronics

Extron electronics MediaLink MLC Plus 50 Manuale utente

Extron electronics

Extron electronics CTR 8 Manuale utente

Extron electronics

Extron electronics HD CTL 100 Manuale utente

Extron electronics

Extron electronics Priority Page Controller PPC 25 Manuale utente

Extron electronics

Extron electronics MLC 206 Manuale elenco delle parti

Extron electronics

Extron electronics Basic MediaLink Controllers MLC 52 IR Manuale utente

Extron electronics

Extron electronics MLC 226 IP Series Manuale utente

Extron electronics

Extron electronics VNM Enterprise Manuale utente

Extron electronics

Extron electronics MLC 226 IP Series Manuale utente

Extron electronics

Extron electronics VNM EC 200 Manuale utente

Extron electronics

Extron electronics MLC 104 IP Plus Series Manuale utente

Extron electronics

Extron electronics TLP Pro 720C Manuale utente

Extron electronics

Extron electronics MLC 226 IP Series Manuale utente

Extron electronics

Extron electronics MEDIALINK MLC 52 Series Manuale utente

Extron electronics

Extron electronics FPC 6000 Manuale utente

Extron electronics

Extron electronics MLC 62 IR D Manuale utente

Extron electronics

Extron electronics MediaLink Controllers with IP Link MLC 104 IP... Manuale utente

Extron electronics

Extron electronics MediaLink MLC Plus 100 Manuale utente

Extron electronics

Extron electronics HD CTL 100 Manuale utente

Extron electronics

Extron electronics VCM 200 D Manuale utente

Extron electronics

Extron electronics PC 101 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente