2
Preparing the Table
WARNING: Wear safety glasses when cutting the hole in the table. Failure to comply may result in eye injury.
ATTENTION:•TheopeninginthetablefortheCableCubbyshouldbecutonlybylicensedandbondedcraftspeople.
• Exercise care to prevent scarring or damaging the furniture.
• Cable Cubby 300 installation — Ensure that the table surface is at least 5/8 inch (0.625") (15.88 mm) thick.
• Cable Cubby 600/800 installation — Ensure that the table surface is at least 3/4 inch (0.75") (19.05 mm) thick.
Cut a hole in the surface where the enclosure will be installed. There are three methods for cutting the hole in the table:
zA hand router and the appropriate Extron Cable Cubby routing template.
HSA 200
USER ACCESS
HSA 200
CABLE CUBBY 300
CABLE CUBBY 300
USER ACCESS
See the table below for part numbers. See the HSA Series and Cable Cubby
Routing Template User Guide, available on the Extron website, www.extron.com,
to prepare the template and use the template to cut the hole.
NOTE: The metal routing template is reusable. Do not discard this
routing template when the installation is complete.
zA CNC wood router and the exact cut-out dimensions for your model. See the
table below for cut-out dimensions:
zA jigsaw and a paper cut-out template (available on the Extron website,
www.extron.com)
NOTE: The underlined dimension in the table below is the side on which
the lid opens.
Routing Template
Part Number
Cut-out Dimensions
Product Width Depth
Cable Cubby 300S 70-237-01 4.65 inches (11.81 cm) 6.00 inches (15.24 cm)
Cable Cubby 300C 70-237-01 6.03 inches (15.32 cm) diameter
Cable Cubby 600 70-239-01 6.49 inches (16.48 cm) 6.49 inches (16.48 cm)
Cable Cubby 800 70-240-01 7.89 inches (20.04 cm) 6.35 inches (16.13 cm)
Preparing the Cable Cubby
TIPS:• InstallanypowermodulesbeforeinstallingAAPs.
• PopulatetheshelfbracketswithcablesandAAPsoutsidetheenclosureandthen
installthepopulatedAAPshelfassemblyintotheenclosure.
Installthepowermoduleandcablesinthepass-throughholesasfollows:
1. Gently push any power modules into the desired position and elevation. Secure the
modules into position with the provided screws and washers.
WARNING: To ensure good electrical grounding, use the star washers with the
screws.
2. Restthecablesinthehalf-mooncutoutsoftwocablepass-throughAAPsegments(Ç)
andsecurethenextcablepass-throughAAPsegmenttotheshelfbracketswiththe
provided #4-40 nuts (É).
3. Repeat step 2fortheremainingcablesandcablepass-throughAAPsegments.
4. Snap the appropriate size split grommet over each cable and into the pass-through holes
with the flange of the grommet on top.
5. Snap the included hole plugs into unused hole.
6. GentlypushtheAAPshelfassemblyintotheenclosureatthedesiredelevation.
EnsurethereisenoughspaceabovetheAAPassemblyfortheCableCubbylidtoclose
completely.SecuretheAAPshelfassemblyintopositionwiththeprovidedscrews.
TIP: IftheAAPshelfassemblydoesnotslideeasilyintothecubby,loosentheAAP
mountingnuts.RetightenthenutsoncetheAAPshelfassemblyisinstalled.
User Access
Cut-Out Template for Extron's
Cable Cubby 200
.350" (0.90 cm)
Print this
template
at 100%
Trim Ring
Lip
Trim Ring’s Outer Edge
0.00” (0.00 cm)
0.02 (0.05 cm)
+
1. Confirm Product to be installed
2. Measure cutout and template
3. After checking, cut opening
1
1
6
2b
4
2a
Cable Cubby 800
Shelf
Bracket
AAP
Shelf
Assy.
Cable Cubby • Setup Guide (Continued)
