Extron electronics FOX3 101 Manuale utente

FOX3 T 101 and FOX3 R 101 • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX3T101 and

FOX3R101 ber optic transmitter and receiver.

WARNING: The FOX3T101 and FOX3R101 output continuous invisible light (Class 1 rated), which may be harmful to

the eyes; use with caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.

CLASS 1 LASER PRODUCT, see the FOX3T101 and FOX3R101 User Guide, at www.extron.com.

AVERTISSEMENT : Le FOX3T101 et FOX3R101 émet une lumière invisible en continu (conforme à la classe1) qui

peut être dangereux pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble

émetteur/récepteur lorsque le câble fibre optique est débranché.

Produit laser de classe1, voir le FOX3T101 et FOX3R101 User Guide sur www.extron.com (en anglais).

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the transmitter and receiver as required. For mounting details and

considerations, see the FOX3 T 101 and FOX3R101 User Guide at www.extron.com.

Step 2 — Input and Output Connections

OUTIN

FOX3 T 101

POWER

12V

A MAX

RESET

INPUT

LOOP OUT

HDMI

Figure 1. FOX3 T 101 Rear Panel

OUTIN

FOX3 R 101

POWER

12V

A MAX

RESET

OUTPUT

HDMI

Figure 2. FOX3 R 101 Rear Panel

a. Connect an HDMI video source to the HDMI input (see figure1, B) on the transmitter.

b. If desired, connect an HDMI video display to the Loop Out port (C) on the transmitter for a local display.

c. Connect an HDMI display to the HDMI output (see figure2, F) on the receiver.

Step 3 — Throughput Connections

NOTE: See the image on the right for fiber cable connections. Connect the transmitter (see figure1 and

figure2, D) to a receiver in one of two ways:

• One way (transmitter to receiver) only, perform step 3a.

• Two way (transmitter to receiver and return), perform steps 3a and 3b.

a. Connect the fiber between the transmitter A Out port and the receiver A In port (1).

NOTE: Ensure that the transmitter and connected receiver are in the same transmission mode,

singlemode (SM) or multimode (MM) and use the correct SM or MM fiber cable to connect the

devices.

b. To return serial data from the receiver to the transmitter, connect a cable between the receiver A Out port

and the transmitter A In port (2).

SFP Link LEDs —

Receiver

ransmitter

OUTIN

• Transmit Optical OUT LED lights solid green when powered and is off when there is no power on the endpoint.

• Receive Optical IN LED lights solid green when light is present and is off when there is no power or light present.

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

Step 4 — Power Connection

Connect the provided 12 VDC power supplies to the rear panel captive screw power inlet (see ﬁgure1 and ﬁgure2, Aon

page1).

ATTENTION:

• Do not connect any external power supplies until you have read the ATTENTION notifications in the Power Supply

section of the user guide for that device.

• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section « Power

Supply » du guide utilisateur pour cet appareil.

Operation

After the receiver, transmitter, and their connected devices are powered up, the system is fully operational. If any problems occur,

verify that the cables are routed and connected properly and the display device has a compatible resolution and refresh rate. If

problems persist, call the Extron S3 Sales & Technical Support Hotline (see the contact number below).

CONFIG

FOX3 T 101

INPUT

SIGNAL

HDCP

AAABBBCCC

Figure 3. FOX3 T 101 Front Panel

CONFIG

FOX3 R 101

INPUT

SIGNAL

HDCP

Figure 4. FOX3 R 101 Front Panel

Indications

APower LED — Indicates power is applied to the unit.

BUSB Config port — Connect a USB-C cable to a computer to configure the device and update the firmware via PCS or

internal web pages.

CInput and Output LEDs —

• Signal LED — Lights when the unit detects an input video signal.

• HDCP LED — Lights when the input signal is HDCP encrypted.

Reset

Press the rear panel recessed reset button (see ﬁgure1 and ﬁgure2, E) if the FOX3 transmitter or receiver rmware is corrupted

or the unit gets disconnected during the update process. The reset allows the product to revert to the factory loaded rmware

(see the FOX3T101 and FOX3R101 User Guide, available at www.extron.com, for details on the reset modes).

Conﬁguration and Control

See the FOX3T101 and FOX3R101 User Guide for details on operating and monitoring the transmitter and receiver using SIS

commands, Extron Product Conguration Software (PCS), or the internal web pages.

NOTE: An Extron Insider account is required to download and use PCS. Contact an Extron support representative, to obtain

an Insider Account.

68-3301-50 Rev. A

07 23

Altri manuali per FOX3 101

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extron electronics Estensione

Extron electronics

Extron electronics DTP DVI 4K 230 D Series Manuale utente

Extron electronics

Extron electronics DDX 102 Tx Manuale utente

Extron electronics

Extron electronics DTP DVI 301 Manuale utente

Extron electronics

Extron electronics Tx-Rx Manuale utente

Extron electronics

Extron electronics FOX 2G Tx AV Manuale utente

Extron electronics

Extron electronics DTP DVI 330 Manuale utente

Extron electronics

Extron electronics HDMI 201 Manuale utente

Extron electronics

Extron electronics VGAUXGA Line Drivers With Audio Extender... Manuale utente

Extron electronics

Extron electronics FOX 3G HD-SDI Manuale utente

Extron electronics

Extron electronics HDMI 230 D Manuale utente

Extron electronics

Extron electronics 60-871-12 Manuale utente

Extron electronics

Extron electronics eLink 100 Manuale utente

Extron electronics

Extron electronics Extension Kits AVTrac 4C Manuale utente

Extron electronics

Extron electronics DDRX DVI Manuale utente

Extron electronics

Extron electronics DTP T 3G-SDI 230 Manuale utente

Extron electronics

Extron electronics Fiber Optic DVI Extenders DVI 104 RX Manuale utente

Extron electronics

Extron electronics DTP T UWP 4K 232 D Manuale utente

Extron electronics

Extron electronics XTP R HWP 201 Manuale utente

Extron electronics

Extron electronics DTP DVI 301 Manuale utente

Extron electronics

Extron electronics DTP T DWP 4K D Series Manuale utente

Extron electronics

Extron electronics DTP2 T 204 Manuale utente

Extron electronics

Extron electronics FOX 500 DVI Manuale utente

Extron electronics

Extron electronics PowerCage FOX Tx HDMI Manuale utente

Extron electronics

Extron electronics FOX3 T 301 Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente