Extron electronics UCS FT 901 Manuale utente

UCS FT 901 and UCS FR 902 • User Guide

The UCS FT 901 and UCS FR 902 extend USB signals from USB 3.2, 2.0, and

1.1 peripheral devices up to 985 ft (300 meters) to a USB 3.2 host computer over

multimode ber optic cable with super speed data transfer rate of up to 5 Gbps.

The transmitter features a USB Type-C connector. The receiver features a

built-in active two-port hub that supplies up to 5 V, 1.5 A each port, to power

attached devices.

The UCS FT 901 and UCS FR 902 are 1 inch (25 mm) high, 3 inches (76 mm) deep, one-eighth rack (transmitter) and quarter rack

(reciever) wide. They can be mounted to a rack or under furniture, or placed on a tabletop.

NOTE:

• This product supports USB data ONLY. DisplayPort Alt Mode and Power Delivery are NOT supported.

• The use of USB 2.0 hub on the UCS FR 902 is not recommended. If a USB hub is needed, Extron recommends using a

USB 3.2 hub. Please contact your Extron AE for more details.

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the

FCC rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related

topics, see the “Extron Safety and Regulatory Compliance Guide” on the Extron website.

Features

• Point-to-point transmission — Extends USB peripherals up to 985 ft (300 meters) over fiber optic cable for point-to-point

applications.

• Supports USB 3.2, 2.0, and 1.1 devices — Supports bulk, control, interrupt, and isochronous transfers as defined by the

USB specification.

• Provides data transfer rates up to 5 Gbps — Allows for the use of USB 3.2 cameras and other USB conference room

peripherals requiring high bandwidth support.

• Integrated dual-port devices — The receiver has two integrated USB ports, which provide up to 5 volts,1.5 amps on each

port. Allows simultaneous connection to multiple peripheral devices such as USB cameras, docks, all-in-one conference

systems, interactive displays, annotation devices, mass storage, keyboards, and mice in pro AV environments.

• Real-time status LED indicators for troubleshooting and monitoring — Front panel LED indicators provide visual

confirmation of active host and link status.

• Rack and furniture mountable — Low-profile, 1-inch (2.5 cm) high, 3-inch deep (7.6 cm), eighth rack wide (UCS FT 901)

and quarter rack wide (UCS FR 902) metal enclosures enable discreet installation, such as beneath a table or behind a

display. One (1) ZipClip 100 and two (2) ZipClip 200 mounting accessories are included.

• VBUS powered transmitter — UCS FT 901 can be powered by host PC or included external power supply.

• External Extron Everlast power supply included — Provides worldwide power compatibility with high-demonstrated

reliability and low power consumption.

• Extron Everlast Power Supply is covered by a 7-year parts and labor warranty

Speciﬁcations

Product specifications are available on the Extron website, www.extron.com.

UCS FT 901 and FR 902 • User Guide (Continued)

Application Diagram

eUCS FR 902

LINK

STATUS

UCS FT 901

LINK

HOST

STATUS

MODEL 80

FLAT PANEL

Fiber

Extron

Cable Cubby

Cable Access

Enclosure

Extron

UCS FT 901

Transmitter

USBC-A

Cable

USB to Web Cam

USB Web Camera

Table

Display

Extron

UCS FR 902

Receiver

Extron

HD Pro Plenum Series

HDMI Premium High Speed

Optical Cables - Plenum

Figure 1. UCS FT 901 and UCS FR 902 Application Diagram

UL Rack Mounting Guidelines

The following Underwriters Laboratories (UL) guidelines pertain to the safe installation in a rack:

1. Elevated operating ambient temperature — If installed in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient temperature. Therefore, install in an environment

compatible with the maximum ambient temperature (Tma = + 122 *F, + 50 *C) specified by Extron.

2. Reduced air flow — Install the equipment in a rack so that the amount of air flow required for safe operation of the

equipment is not compromised.

3. Mechanical loading — Mount the equipment in the rack so that a hazardous condition is not achieved due to uneven

mechanical loading.

4. Circuit overloading — Connect the equipment to the supply circuit and consider the effect the circuit overloading might

have on an overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be

used when addressing this concern.

5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted equipment. Pay particular attention to supply

connections other than direct connections to the branch circuit (such as use of power strips).

Rear Panel Connections

Transmitter — UCS FT 901

UCS FT 901

LINK

HOST

STATUS

POWER

12V

0.1A MAX

HOST

USB-C

SS 5G

OUTPUT

A B C

A B

Figure 2. Transmitter Rear Panel Connectors

Receiver — UCS FR 902

eUCS FR 902

LINK

STATUS

POWER

12V

1.6A MAX

DEVICES INPUT

1.5 A

A C

Figure 3. Receiver Rear Panel Connectors

APower connector —

• Transmitter — Connect the provided 0.5 A max. external power supply to this 2-pole, 3.5mm captive screw connector.

• Receiver — Connect the provided 2.0 A max. external power supply to this 2-pole, 3.5mm captive screw connector.

ATTENTION:

• The power supply must not be permanently xed to the building structure or similar structures.

• La source d’alimentation ne devra pas être xée de façon permanente à une structure de bâtiment ou à une

structure similaire.

• Do not mount the power supply in air handling spaces or in wall cavities.

• Ne pas installer la source d’alimentation dans des espaces d’aération ou dans des cavités murales.

• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA

70, article 725 and the Canadian Electrical Code part 1, section 16.

• Cette installation doit toujours être conforme aux dispositions applicables du Code américain de l’électricité

(National Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité, partie 1, section 16.

• The power supply must be located within the same vicinity as the Extron AV processing equipment in an ordinary

location, Pollution Degree 2, secured to a podium, a desk, or an equipment rack within a dedicated closet.

• La source d’alimentation doit être située à proximité de l’équipement audiovisuel Extron dans un emplacement

habituel, avec un degré de pollution 2, xée à une estrade, un bureau, ou dans une baie technique à l’intérieur d’un

placard dédié.

• Always use a power supply provided by or specied by Extron. Use of an unauthorized power supply voids all

regulatory compliance certication and may cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. L’utilisation d’une source

d’alimentation non autorisée annule toute certication de conformité réglementaire, et peut endommager la source

d’alimentation et l’unité.

• If not provided with a power supply, this product is intended to be supplied by a power source marked “Class 2” or

“LPS” and rated at 12 VDC, minimum 1.5 A.

• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit être alimenté par une source

d’alimentation de classe 2 ou LPS et paramétré à 12 V et 1,5 A minimum.

BHost (Input) connector — Connect a USB Type A-to-C or USB Type C-to-C cable between this USB C port and a USB 3.2

port of a host device. The UCS FT 901 can be powered by a connected host via VBUS power or by external power supply.

NOTE: The transmitter is compatible with USB 3.2 host ports ONLY. USB 3.2 connectors are either blue Type A, Type C,

or labeled with SuperSpeed trident logo (see images at right).

CFiber I/O connectors —

• Transmitter — Connects multimode fiber optic cable from the receiver Input connectors to the transmitter Output

connectors.

• Receiver — Connects multimode fiber optic cable from the transmitter Output connectors to the receiver Input

connectors.

DUSB Devices connectors — The two built-in female USB Type A connectors are USB 3.2, 2.0, and 1.1 compatible,

providing +5VDC at up to 1.5 A to connected USB peripherals requiring power.

UCS FT 901 and FR 902 • User Guide (Continued)

Cabling and Setup

Figure 4 shows connections for the UCS FT 901 and UCS FR 902.

POWER

12V

HOST

USB-C

SS 5G Tx

OUTPUT

POWER

12V

1.0A MAX

INPUT

OUTPUTS

WER

A MAX

INPUT

UTPUT

POWER

12V

DEVICES INPUT

1.5 A

1.6A MAX

Ground

+12 VDC input

External Power Supply

(12 VDC, 2.0 A max.)

Ground all

Devices

Ground

+12 VDC input

External Power Supply

(12 VDC, 0.5 A max.)

Ground all

Devices

0.1A MAX

USB

USB Camera

Receiver

USB

Laptop

Transmitter

Multimode Fiber Optic Cable

Compatible with USB 3.2, 2.0, 1.1

peripheral devices

Compatible with USB 3.2

host ports ONLY

Figure 4. Transmitter and Receiver Connection with Two External Power Supplies

Installation Procedure

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués uniquement par un technicien qualié.

To ensure proper operation, the transmitter, receiver, USB host, and USB peripherals must be connected properly and in the

sequence described here (see gure4).

1. Power off all devices that will be directly connected to the receiver.

2. Wire each of the two provided power supplies to their 2-pole captive screw connectors (see figure5).

Captive Screw Connector

Tie Wrap

Heat

Shrink 1/8"

(3 mm)

7/8"

(22 mm)

3/16"

(5 mm) Max.

Figure 5. Wiring the Power Connector for the UCS FT 901 and FR 902

NOTE: The UCS FT 901 (transmitter) can also be powered by the host device, without the need for the external power

supply.

3. Plug the two power supply connectors into their respective transmitter or receiver rear panel connectors (see figure4, 3).

Connect the 6 Watt power supply (1) to the transmitter, and the 24 Watt (2) to the receiver.

The green Power LED (see ﬁgure 6, A, on the next page) on the front panel of each device lights when each device is

powered on.

4. Connect a USB Type A-to-C or Type C-to-C cable from the host device to the transmitter Host port (4). The Host LED

(ﬁgure 6, B) will light, indicating that communication between the transmitter and host device has been established.

5. Connect a multimode fiber optic cable from the Output port of the transmitter to the Input port of the receiver (figure 4, 5).

The transmitter and receiver front panel Link LEDs will light steadily (figures 6 and 7, C).

6. If appropriate, choose a location and mount the transmitter and receiver

• For rack mounting, fasten the enclosure to the rack or rack shelf.

• For furniture mounting, see ZipClip 100 and 200 Mounting Installation on the next page.

• For table mounting, attach the provided four rubber feet to the bottom of the unit and place it where desired.

7. Power on the host computer. On the transmitter, the Host and Link LEDs (Band C) light when the computer recognizes the

transmitter, and when the transmitter and receiver are connected with each other.

8. Connect up to two USB peripheral devices (such as a camera, keyboard, touchpanel or printer) to the receiver USB ports

(figure 4, 6).

The system is now ready to operate.

Front Panel Features

Transmitter – UCS FT 901

UCS FT 901e

LINK

HOST

STATUS

POWER

12V

0.1A MAX

HOST

USB-C

SS 5G Tx

OUTPUT

A B C

A B

Receiver – UCS FR 902

eUCS FR 902

LINK

STATUS

POWER

12V

1.6A MAX

DEVICES INPUT

1.5 A

A C

Figure 6. Transmitter Front Panel Figure 7. Receiver Front Panel

APower LED — This green LED lights to indicate that the unit is receiving power.

BHost LED — This green LED lights when the transmitter is powered, and communicating with the host PC.

CLink LED — This green LED lights when the transmitter and receiver are connected by a fiber optic cable, receiving power.

UCS FT 901 and FR 902 • User Guide (Continued)

ZipClip 100 and 200 Installation and Mounting

Both the UCS FT 901 and UCS FR 902, alongside their respective external power supplies (PS 1205 C and PS 1215 C), can be

mounted under a desk, onto a wall or other furniture using the ZipClip 200 and 100 (included). See ZipClip mounting options at

www.extron.com.

1. Mount the ZipClip 200 to an under-desk

mounting surface or to a rack rail using

the four included mounting screws (see

figure 8).

For the receiver power supply

(PS 1215 C), also mount the ZipClip

100, adjacent to the ZipClip 200.

Figure 8. Under-desk Mounting (ZipClip 100 and ZipClip 200)

2. Mount the UCS transmitter or

receiver to the ZipCaddy 200.

If mounting the transmitter, also

mount its external power supply

(PS 1205 C) as follows:

Align the mounting holes on the

bottom of the UCS unit with the

mounting holes on the ZipCaddy

(see gure 9), and fasten the

screws.

NOTE: The receiver power

supply (PS 1215 C) attaches

directly to the ZipClip 100

(see ﬁgure 10 on the next

page).

Figure 9. ZipCaddy Mounting (UCS FT 901 and UCS FR 902)

ZipClip 200

ZipClip 100

100

UCS FT 901

LINK

HOST

STATUS

ZipCaddy 200

PS 1205 C

UCS FT 901

UCS FR 902

LINK

STATUS

ZipCaddy 200

UCS FR 902

3. The transmitter (with power supply) or receiver can now

be easily attached and detached from the ZipClip 200

mounting location, using the quick-release tab.

The receiver power supply (PS 1215 C) can be attached

and detached from the ZipClip 100 (no ZipCaddy

necessary).

Figure 10. Attaching and Releasing the UCS FT 901, UCS FR 902,

and PS 1215 C

UCS FT 901

LINK

HOST

STATUS

UCS FT 901

ZipClip 200

PS 1205 C

UCS FR 902

LINK

STATUS

ZipClip 200

ZipClip 100

PS 1215 C

UCS FR 902

68-3621-01 Rev. B

04 21

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

System Operation

No drivers are required for a host PC to function with the UCS FT 901 and UCS FR 902. The transmitter is detected by the

operating system, and appropriate USB drivers are loaded. Certain USB peripherals, such as gaming keyboards, USB interactive

white boards, scanners, printers, and similar devices, require specic drivers installed on the PC. To obtain drivers, see the USB

device installation instructions or the peripheral device manufacturer website.

The system is fully operational when the transmitter, receiver, PC or USB host, and peripherals are connected and powered.

If problems are encountered, ensure that all cables are routed and connected properly, and that the latest drivers for each

peripheral are installed.

Troubleshooting

USB signals are generally reliable, but are susceptible to bad connections or signal losscables that are too long. The ber optic

cables can have the same issues. To avoid loss of data and communication, follow these guidelines:

• The USB cables that connect the transmitter to the host, or the receiver to peripheral devices, should not exceed 6feet

(1.8meters).

• When connecting the host or peripherals, use only cables designed for USB signals.

• Avoid or limit the use of adapters.

• The UCS FT 901 and UCS FR 902 work as described in point-to-point applications. Do not use additional adapters, patch

panels, or couplers with USB cables or fiber optic cables. Additional links in the signal chain can result in reduction of signal

integrity and overall system performance.

When properly connected and operating, the transmitter and receiver Power LEDs, Link LEDs and Host LEDs are lit. Front

panel LEDs are also useful for troubleshooting. The following table outlines the status indicated by each LED:

Transmitter Receiver

LED

Indicator On Off On Off

Power Transmitter is connected to

a host PC or 12 VDC power

supply, and is operating

properly.

Transmitter is NOT connected

to a host PC or 12 VDC power

supply, or is defective.

12 VDC power supply is

connected and operating

properly.

12 VDC power supply is not

connected, or is defective.

Link Both transmitter and

receiver have power, and

are connected properly

by a multimode fiber optic

cable.

If both Power LEDs are on, the

multimode fiber optic cable is

not connected or is improperly

wired.

If either Power LED is off, see

the Power LED troubleshooting

instructions above.

Both transmitter and

receiver have power, and

are connected properly

by a multimode fiber optic

cable.

If both Power LEDs are on,

the multimode fiber optic

cable is not connected or is

improperly wired.

If either Power LED is

off, see the Power LED

troubleshooting instructions,

above.

Host When transmitter power

LED is on, this Host LED

lights when communication

with host PC is established.

If transmitter power LED is on,

USB cable is not connected.

N/A N/A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extron electronics Estensione

Extron electronics

Extron electronics DTP HDMI 330 Manuale utente

Extron electronics

Extron electronics DTP T DWP 4K 232 D Manuale utente

Extron electronics

Extron electronics FOX 2G Tx AV Manuale utente

Extron electronics

Extron electronics USB Extender Plus Series Manuale utente

Extron electronics

Extron electronics DTP T 3G-SDI 230 D Manuale utente

Extron electronics

Extron electronics DTP DVI 4K 230 D Series Manuale utente

Extron electronics

Extron electronics FOX T USB Manuale utente

Extron electronics

Extron electronics FOX T Plus MM Manuale utente

Extron electronics

Extron electronics FOX3 SR 20 Manuale utente

Extron electronics

Extron electronics FOX T USB Extender Plus Manuale utente

Extron electronics

Extron electronics DTP DVI 330 Manuale utente

Extron electronics

Extron electronics USB Extender Tx Manuale utente

Extron electronics

Extron electronics DTP HDMI 301 Manuale utente

Extron electronics

Extron electronics DTP T UWP 4K 232 D Manuale utente

Extron electronics

Extron electronics FOX II T DP 4K Manuale utente

Extron electronics

Extron electronics FOX T UWP 302 Manuale utente

Extron electronics

Extron electronics HFX 100 Tx Manuale utente

Extron electronics

Extron electronics HDMI 230 D Manuale utente

Extron electronics

Extron electronics eLink 100 Manuale utente

Extron electronics

Extron electronics DTP HDMI 230 Manuale utente

Extron electronics

Extron electronics Fiber Optic DVI Extenders DVI 104 RX Manuale utente

Extron electronics

Extron electronics DTP T DWP 4K D Series Manuale utente

Extron electronics

Extron electronics DTP T HWP 232D Manuale utente

Extron electronics

Extron electronics Extender Wall Mount Series Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente