Extron electronics Cable Cubby 1252 MS Manuale utente

Cable Cubby 1252 MS • Installation Guide

This guide provides instructions for an experienced technician to install the Extron

Cable Cubby 1252 MS.

The Cable Cubby 1252 MS is a furniture-mounted enclosure for cable access,

connections, and AC power. The Cable Cubby 1252 MS provides the freedom to either

match the surface of the table or use a unique lid design that complements the room décor.

Unused cables can be stored out of the way while remaining connected to the presentation system.

NOTE: This product is intended for use only with Extron UL listed power modules (not included).

Planning

Check with local and state regulations before starting the installation

Ensure that the planned installation complies with national and local building and electrical codes.

Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Check all parts and equipment before installation

Ensure that all parts are present in the kit.

Ensure that necessary tools and equipment are available for the installation.

Kit Contents

Part Quantity Part Quantity

Connectivity bracket

1 Retractor pin and clip

#4-40 at head module

screws 4#6-32 pan-head mounting

screws and star washers

AAP frame plate

1#4 at head lid insert wood

screws 4

Cable grommet plate

1 Trim brackets

Hole plugs

6 (3/8"),

2 (1/4")

#8 pan head wood mounting

screws 12

Retractor bracket

ZipClip screws and washers

(for mounting of optional

ZipClip power supply)

Extron

Cable Cubby 1252 MS • Installation Guide (Continued)

Preparing the Table and Cable Cubby 1252 MS Lid

Prepare the lid and cut a hole in the surface where the enclosure will be installed. Read the following information before making a

cut.

Determine the best location for the enclosure

Ensure that the location where the Cable Cubby 1252 MS is to be installed is convenient for as many users as possible.

Ensure that the edge on which the lid opens is oriented correctly.

Ensure that there is ample space under the table for cables. Allow at least 36 inches of cable loop for each cable (see

Routing and Connecting Cables on page 10).

When installing retractors in the Cable Cubby, ensure that there is enough space for the retractor assembly under the table or

furniture (see the Dimensions with a Retractor on page 11 for retractor dimensions).

Prepare the table

ATTENTION:

• The correct dimensions for the cut in the table surface depend on the thickness of your lid material.

• If the total lid thickness is equal to or thicker than the table surface, see ﬁgure 1 on page 3.

• If total lid thickness is thinner than the table surface, see ﬁgure 2 on page 3.

• Les dimensions correctes pour la découpe dans la surface de table dépendent de l’épaisseur de votre couvercle :

• Si l’épaisseur totale du couvercle est égale ou plus importante que la surface de la table, regardez la

ﬁgure 1.

• Si l’épaisseur totale du couvercle est moins importante que la surface de la table, regardez la

ﬁgure 2.

• For a professionally-installed appearance, the mounting surface for the Cable Cubby 1252 MS requires precise cuts.

Extron strongly recommends cutting the hole via a computer numerical control (CNC) machine only.

• Pour offrir un design professionnel, il est nécessaire de couper avec précision la surface de montage du

Cable Cubby 1252 MS. Extron recommande vivement de percer le trou uniquement à l’aide d’une machine-outil à

commande numérique.

• The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople. Exercise care to

prevent scarring or damaging the furniture.

• L’ouverture dans la table pour le Cable Cubby doit être coupée uniquement par un ouvrier détenteur d’une licence.

Veillez à ne pas laisser de marques ni à détériorer le mobilier.

1. Cut a hole in the table for the Cable Cubby 1252 MS. See the table below to determine:

• The location and orientation of the cut on the table

• The correct size of the cut, based on the thickness of the table surface and the lid.

ALid is thicker than or as thick as the table surface BLid thickness is thinner than table surface

Extron

ExtronExtron

NOTE: A thinner lid requires a slightly larger cut

because the enclosure extends into the cut-out.

Figure 1. Thicker Lid Material Figure 2. Thinner Lid Material

SURFACE

CUT-OUT

AREA

Bottom View

Front (Width)

Rear (Width)

2.00"

(50.8 mm)

2.00"

(50.8 mm)

0.63"

(16.0 mm)

10.50"

(266.7 mm)

0.63"

(15.9 mm)

R= 0.25" (6.3 mm)

Cut Dimensions

Thicker table surface:

Width: 8.81 inches

(223.8 mm)

Depth: 5.25 inches

(133.3 mm)

Corner 0.25 inch

radius: (6.3 mm)

Cut Dimensions

Thinner table surface:

Width: 9.5 inches

(241.3 mm)

Depth: 5.25 inches

(133.3 mm)

Corner 0.25 inch

radius: (6.3 mm)

Figure 3. Enclosure Dimensions and Mounting Hole Locations

2. Mark and pre-drill pilot holes, 1/8-inch in diameter,

8.56"

(217.4 mm)

4.43"

0.81"

(112.5 mm)

MAX

(20.6 mm)

(Varying thickness

)

0.2"

(5 mm) Radius Corners

1/2-inch deep at the six mounting locations shown ( ) in

gure 3.

3. Fabricate the Cable Cubby lid to the dimensions shown

at right.

NOTE: Make the cut as accurate as possible, the

cutout piece can be used for the lid to be attached

to the Cable Cubby.

Cable Cubby 1252 MS • Installation Guide (Continued)

Preparing the Cable Cubby

Step 1 — Assemble Connectivity Modules

Connectivity modules allow you to populate the Cable Cubby enclosure with a combination of AAP modules, cable pass-through,

or retractors. Follow the steps below to assemble the connectivity modules of your choice.

Option 1: AAP module

Secure up to three single-space

AAP modules in the AAP frame

plate.

#4-40 Nut with

Captive Washer

Secure the AAP frame plate on the connectivity

brackets, using four of the provided #4-40 module

screws. Use a screwdriver to tighten the screws.

2Insert cables through the bottom of the connectivity bracket.

Connect cables to the AAP modules.

NOTE: After assembling the module, proceed to Step 2 — Install the Modules on page 5.

Option 2: Cable pass-through module

Secure the grommet plate

on the connectivity bracket,

using four of the provided

#4-40 module screws. Use

a screwdriver to tighten the

screws.

Insert cables through the bottom

of the connectivity bracket and

into the holes of the grommet plate. Snap the included

hole plugs into any

unused holes.

NOTE: After assembling the module, proceed to Step 2 — Install the Modules.

Option 3: Retractor Bracket

Use the retractor bracket to mount retractors in the Cable Cubby 1252 MS enclosure.

Extron

Secure the bracket using four of the

provided #6-32 pan-head mounting

screws with star washers.

Use a screwdriver to tighten the scr

ews.

Insert the bracket as shown.

The bracket may be installed on the left

or right side of the enclosure and at the

lowest height.

NOTES:

• After installing the bracket, proceed to “Step 2 — Install the Modules” to install the power module.

• After mounting the Cable Cubby on the table, install the Retractors (see Installing Retractors on page 8).

Step 2 — Install the Modules

Determine where the connectivity modules and power module will be installed in the Cable Cubby. The modules may be installed

on the left or right side of the enclosure and at various heights.

NOTE: Ensure that there is enough room above the modules for the Cable Cubby lid to close completely.

Extron

125V~ 12A MAX TOTAL

Secur

e the modules using four of the

provided #6-32 pan-head mounting

screws and star washers. Use a

screwdriver to tighten the screws

Insert the modules

into the Cable Cubby.

WARNING: Risk of Electric Shock. To ensure proper

electrical grounding, use the provided #6-32 mounting screws

with the star washers.

AVERTISSEMENT : Risque de choc électrique. An

d’assurer une mise à la terre correcte, utilisez les xations de

mise à la terre #6-32 et les rondelles en étoile fournies.

Cable Cubby 1252 MS • Installation Guide (Continued)

Step 3 — Mount the lid onto the Cable Cubby

If using screws,

perform 2and 3.

If NOT using screws,

perform 4.

Option 2a: Mount lid

insert with screw

Mark and drill four

1/16-inch pilot holes.

Secur

e the lid onto the

Cable Cubby using #4

at head wood

screws.

— OR —

Option 2b: Mount the

fabricated lid without

screws

Secur

e the lid onto the

Cable Cubby using the

proper adhesive.

Align the lid to the Cable

Cubby. The back edge of

the lid lines up with the back

edge of the lid mechanism.

mechanis

Extron

Mounting the Cable Cubby in the Table

1. See the dimension on ﬁgure 3 on page 3 for the mounting hole locations OR have an assistant hold the Cable Cubby against

the underside of the mounting surface.

2. Install the screws in the two center pre-drilled mounting holes on each side, leaving 1/8 inch (4 mm) of the screw head

exposed.

3. Use the two center slotted mounting holes on the mounting bracket to hang the Cable Cubby on the two installed screws.

4. Snug the two screws just so that the Cable Cubby can still be moved on its slotted holes.

5. Adjust the Cable Cubby position and alignment.

6. Tighten the center mounting screws while maintaining the position and alignment of the Cable Cubby.

7. Install the remaining mounting screws and secure the Cable Cubby to the table.

Step 1 — Perform height adjustment

NOTE: If the lid is the same thickness as the table, proceed to Step 2: Install trim brackets on page 8.

If the lid thickness is different than the table

thickness, loosen, but do not remove, the

wing bolts (two on each side), just enough

to allow the Cable Cubby to slide up and

down in the brackets.

Raise the unit up or down until the lid is ush with

the table top surface. Use an assistant if necessary.

Firmly tighten the wing bolts.

NOTE: If the lid is thinner than the table

surface, it may be necessary to relocate

the wing bolts to the bottom position of

the Cable Cubby.

Cable Cubby 1252 MS • Installation Guide (Continued)

Step 2 — Install trim brackets

If there is a gap, front and back, between the underside of the table and the Cable Cubby frame, install the trim brackets as follows:

Hold the trim bracket

against the underside of the

table, ush against the Cable

Cubby and centered on the unit.

Mark the three mounting holes.

Drill 1/8 inch (3 mm) diameter pilot holes,

1/2 inch (12.7 mm) deep.

Secure the trim bracket to the table using the

provided #8 wood screws.

Repeat through on the opposite of the Cable

Cubby.

1 3

Installing Optional Accessories

Installing Retractors

For horizontal or angular retractor mounting, see the information at right, then follow the steps below.

Insert the pin through the

Retractor mounting hole

on the side of the

Cable Cubby and

Retractor assembly.

Secure the clip

on the pin.

Insert Retractors into

the Retractor bracket.

Secure the locking screw

on each Retractor. Do not

overtighten.

Clip

Extron

Angular Mounting

Remove the enclosure screws as shown above, then follow

this step:

Horizontal Mounting

Cable Release

Assembly

Move the cable release assembly upward until

the angular mounting hole is visible. Reinstall the

enclosure screws in this hole (both sides).

Remove two enclosure screws

(one on each side) from this position.

Then, mount the Retractors as shown

at left.

Cable Release

Assembly

See the Cable Retractor Series Setup Guide, available on

the Extron website, for additional steps.

Remove two enclosure screws

(one on each side) from this position.

Then, mount the Retractors as shown

at left.

Move the cable release assembly upward until

the angular mounting hole is visible. Reinstall the

enclosure screws in this hole (both sides).

Installing an optional ZipClip 100 or ZipClip 200 mounting kit

ZipClip 100 mounts

horizontally with the

push tab to the right.

ZipClip 200 mounts

vertically on the bottommost

mounting location with the push tab up.

Cable Cubby 1252 MS

Use the provided ZipClip screws

and washers to mount the ZipClip

to the Cable Cubby 1252 MS.

Installing an optional PMK 155 Product Mounting Kit

PMK 155

Mount the device (up to 1.75 inch [44.4 mm] tall) and power supply to the PMK 155 (see the PMK 155 Installation Guide)

Install the two supplied Allen bolts from the

PMK 155 kit to the shelf leaving approximately

1/8 inch (4 mm) protruding.

Slide the shelf sideways horizontally onto the

Cable Cubby mounting bracket from the front

of the enclosure, on either the left or right side,

until the shelf drops into the slot in the bracket.

Tighten the bolts with a 4 mm Allen wrench.

Dress the cables associated with the device

installed on the shelf using tie wraps.

Connect cables to the system.

NOTE: The pipe clamp that is included with the PMK 155 is not

required for the Cable Cubby installation and can be discarded.

Side view with bracket

Cable Cubby 1252 MS • Installation Guide (Continued)

Routing and Connecting Cables

For cable pass-through applications,

allow at least 36 inches (0.9 m) of cable

loop for each cable.

Connect cables to the AV system

and connect the AC power cord.

Using zip ties, secure cables to the holes

on the bottom of the Cable Cubby.

Extron

Indice

Altri manuali Extron electronics Elettricità industriale

Extron electronics

Extron electronics WPD 120 A Manuale utente

Manuali Elettricità industriale popolari di altre marche

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Manuale tecnico

Abtech

Abtech HVJB Series Guida

Murata

Murata GRM0335C1H8R1DA01 Series Manuale utente

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Manuale utente

Eaton

Eaton Ulusoy HMH24-04 Manuale utente

Newlong

Newlong NP-7H Manuale utente

Murata

Murata GJM0335C1E4R4BB01 Series Manuale utente

Stahl

Stahl 8575/12 Manuale utente

SI Pegasus Manuale utente

Murata

Murata GRM1555C1H2R7CA01 Seies Manuale utente

Murata

Murata GRM0225C1E6R4BA03 Series Manuale utente

Cooper Power Systems

Cooper Power Systems VXE15 Manuale utente

S&C

S&C Vista SD Manuale utente

Murata

Murata GRM0335C2A7R3CA01 Series Manuale utente

Siemens

Siemens 3VA9988-0BM10 Manuale utente

Siemens

Siemens SITRANS LVS100 Manuale utente

Murata

Murata GRM32ER60G227ME05 Series Manuale utente

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Manuale utente