Extron electronics TouchLink Series Istruzioni per l’uso
Best Practices Guide
Extron TouchLink™
Touchpanel Configuration
TouchLink™Touchpanel Best Practices
Page 2
Contents
INTRODUCTION .................................................. 3
GETTING STARTED
1. Know Your AV System............................................ 4
2. Upgrade Your Firmware........................................... 4
3. Upgrade Your Software ........................................... 5
4. Update Your Device Drivers ........................................ 5
CONFIGURATION
5. Initial Setup .................................................... 6
6. Save Unused Pages and Pop-ups in GUI Configurator ................... 6
7. Include Location in Your Naming Convention........................... 7
8. Use Master Pages............................................... 7
9. Use Modal Pop-up Pages ......................................... 8
10. Be Consistent With Button Placement................................ 8
11. Use Contrasting Colors With Your Text and Backgrounds ................. 9
12. Use Alignment Tools ............................................. 9
13. Use the Copy Properties Tool ...................................... 9
14. ID Management................................................ 10
15. Time Delay Requirements ........................................ 10
16. Use Feedback ................................................. 11
17. Use Front Panel Lock – Executive Mode ............................. 11
18. Use Side Buttons Appropriately.................................... 11
19. Button Naming For Global Viewer .................................. 11
TESTING AND TROUBLESHOOTING
20. Test with Global Viewer .......................................... 11
TouchLink™Touchpanel Best Practices
Page 3
INTRODUCTION
TouchLink is the first fully configuration-based touchpanel. When combined
with an Extron IP Link®Control Processor, TouchLink has the power to handle
the control needs of single display rooms, dual display rooms, divisible rooms,
multi-image systems, and video conference suites.
To deploy TouchLink Touchpanels, Global Configurator - GC and GUI
Configurator - GUIC software are required. These software products are used
to configure your AV control system and set up your TouchLink Touchpanel
interface.
This document is a collection of best practices designed to ensure a quick
and successful installation of your Extron TouchLink Touchpanel-based control
system.
TouchLink™Touchpanel Best Practices
Page 4
GETTING STARTED
The first step in setting-up your TouchLink Control System
1. Know Your AV System
Become familiar with the components of your AV system. This knowledge is necessary to determine the pages, pop-ups,
and buttons that should be a part of the graphical user interface on your TouchLink Touchpanels.
100-240V 50-60Hz
I
N
P
U
T
VID
VID
YC
YB-Y R-Y RGBDVI 8
1
245
3
L
2
13456
7
R
AUDIOINPUT
L
A
BRS-232
R
OUTPUT
L R
OUTPUT
RGB
Y,B-Y,R-Y
8
7
RGB
6
LISTED
1T23
I.T.E.
CUS
INPUT
LAN
POWER
12V
500mA
MAX 1 2 3 4
COM3 IR
3
SGSG
TXRX 4
RELAY
34
COM1
TXRX
RTSC TS
COM2 IR
1
S G S G
TXRX 2
RELAY
12
Extron
ON
OFF
DISPLAY
MUTE
SCREEN
UP
SCREEN
DOWN
VCR
DVD
DOC
CAM
LAPTOP
PC
XPA1002
12
LIMITER/PROTECT
SIGNAL
OVER
TEMP
Extron
XPA 1002
Power Amplier
Extron
TLP 700MV
7" TouchLink
Panel
Extron
IPL 250
IP Link Ethernet
Control Processor
TCP/IP
Network
Lighting
System
Projector
Screen
Control
Laptop
DVD
Player
Ext
ron
IN
1508
Scaling P
resentation
Swit
cher
PC
DVI
Motion
Detector
RS-232
RS-232
RS-232
Contact
Closure
IR Control
to DVD
IR Control
from IPL 250
Relay
Extron
IR Emitter
Single Display - System Design Drawing
2. Upgrade Your Firmware
Your TouchLink or IP Link products may benefit from periodic firmware updates that enable new features and capabilities.
Firmware can be found on the Extron website at: http://www.extron.com/firmware. Please read all applicable release
notes before upgrading firmware. For detailed instructions, and to verify your current firmware version, refer to the
Firmware Upload FAQ Guide. Upgrades from some older firmware versions call for a device reset and for re-uploading
of your original Global Configurator and/or GUI Configurator project files.
Firmware Loader
TouchLink™Touchpanel Best Practices
Page 5
3. Upgrade Your Software
TouchLink Touchpanels use GUI Configurator V1.0 and Global Configurator V3.0 or later for setup. Current versions of
GUI Configurator and Global Configurator can be downloaded from the Extron website at: http://www.extron.com/
TouchLink. Keeping the most recent versions of software will help ensure you fully utilize your control systems. Please
review Release Notes before updating software.
Downloading TouchLink Software
4. Update Your Device Drivers
The latest Extron device drivers can be downloaded from: http://www.extron.com/download/driverfilter.aspx. All driver
files should be placed in the “Driver2” folder on your computer. This folder’s location can vary, but can easily be located
from within the Global Configurator program. In Global Configurator under “Help” is the “About GC3” dialog box. Simply
click on “Help” - “About GC3” - and click on the link that reads, “Open the driver folder.”
Downloading Device Drivers
TouchLink™Touchpanel Best Practices
Page 6
CONFIGURATION
To configure your TouchLink Control System, start with Global Configurator for initial set-up. Next, use GUI Configurator
to configure graphical elements – your pages and pop-ups. Lastly, go back to Global Configurator to configure additional
features.
Start with Global Configurator
5. Initial Setup
In Global Configurator, select your IP Link control processor and add drivers for your devices. Check the Communication
Sheets for each device to verify your commands. This helps determine which buttons are needed in your graphical user
interface, or GUI. Drivers for commonly used devices like digital signal processors and video conference units come with
specific instructions.
Accessing the Driver Communication Sheet from GC
Switch to GUI Configurator
6. Save Unused Pages and Pop-ups in GUI Configurator
After selecting your template in GUI Configurator, do not delete unwanted pages and pop-ups. Instead, de-link them from
your buttons. These pages and pop-ups may become useful when updating your system in the future.
Removing Doc Cam button and saving Doc Cam popup
TouchLink™Touchpanel Best Practices
Page 7
7. Include Location in Your Naming Convention
Pages and pop-ups should be named after the location and device they control. For example, if you have two DVD
players and need one pop-up for each, rather than naming the pop-ups DVD 1 and DVD 2, it is clearer to name them
DVD-Classroom101 and DVD-Classroom102. Adding location information to your naming conventions makes it easier to
differentiate and assign page flip commands to your buttons.
Naming Convention in GUI Configurator
8. Use Master Pages
Items common to most pages and pop-ups in your control system should be placed on a Master Page and Master Pop-
up, respectively. For example, if there is only one volume control needed in a system, it is a good practice to place it on
the Master Page.
Master Page
TouchLink™Touchpanel Best Practices
Page 8
9. Use Modal Pop-up Pages
Modal pop-up pages block operations until another, pre-determined task is completed. For example, a modal pop-up
page could block access to the touchscreen while the controller is performing the auto-image function.
10. Be Consistent With Button Placement
Be consistent in your placement of buttons from page to page. For example, if your DVD page has the Rewind, Play, and
Fast-Forward buttons at the top of the page, place these same buttons at the top of the VCR page as well.
DVD Popup
VCR Popup
TouchLink™Touchpanel Best Practices
Page 9
11. Use Contrasting Colors With Your Text and Backgrounds
To ensure text is legible, use a text color that highly contrasts with the background color. Please reference our GUI
Design Guide for more information on this topic, as well as general GUI design guidelines.
12. Use Alignment Tools
From GUI Configurator, use the alignment tools to position buttons on your pages. Doing so guarantees that your buttons
are placed in precisely the same spot on every page, eliminating the problem of buttons that appear to “jump” when
navigating between pages.
Alignment Tools
13. Use the Copy Properties Tool
The “Copy Properties” tool will copy only the properties of one object to another. For example, to keep your buttons of
consistent size, the “Copy Properties” tool can be used to copy and paste the button size only – leaving other attributes
untouched.
Copying Object Properties
TouchLink™Touchpanel Best Practices
Page 10
14. ID Management
Use caution when assigning IDs to your buttons. The “Where Used” window in GUI Configurator is a useful tool for
tracking and managing the button IDs. Additionally, the “Show Control Info” option under the “Window” menu indicates
which ID is currently assigned to each button.
Enabling Where Used Window
Enabling Show Control Info opton
To export the completed GUI project and import that project to
Global Configurator, please refer to the How Do I...? document.
15. Time Delay Requirements
Any control that requires time delay must be configured from Global Configurator. For example, “System ON” button
needs a time delay to allow the projector to warm up. Leave this button un-configured in GUI Configurator and configure it
from within Global Configurator.
Indice
Altri manuali Extron electronics Pannello touch
Extron electronics
Extron electronics TLP 1000MV Manuale utente
Extron electronics
Extron electronics BB 1000M Manuale utente
Extron electronics
Extron electronics TLP Pro 720M Manuale utente
Extron electronics
Extron electronics TLP 700MV Manuale utente
Extron electronics
Extron electronics TouchLink TLP Pro 1025T Series Manuale utente
Extron electronics
Extron electronics TLP 700TV Manuale utente
Extron electronics
Extron electronics RWM 1 Manuale utente
Extron electronics
Extron electronics TLP Pro 725T Manuale utente
Extron electronics
Extron electronics TLP Pro 1220TG Manuale utente
Extron electronics
Extron electronics TouchLink TLP 710CV Manuale utente
Extron electronics
Extron electronics TLP Pro 720C Manuale utente
Extron electronics
Extron electronics TLP Pro 1725TG Manuale utente
Extron electronics
Extron electronics TLP Pro 1220MG Manuale utente
Extron electronics
Extron electronics TLP Pro 720M Manuale utente
Extron electronics
Extron electronics TLP Pro 1225TG Manuale utente
Extron electronics
Extron electronics TLP Pro 720M Manuale utente
Extron electronics
Extron electronics TLP Pro 525M seriesl Manuale utente
Extron electronics
Extron electronics TouchLink TLP 710TV Manuale utente
Extron electronics
Extron electronics TLP 710MV Manuale utente
Extron electronics
Extron electronics TouchLink TLP Pro 1020 Series Manuale utente
