Ezviz L2S Manuale utente
2
Overview
Indoor
Outdoor
Fingerprint Reader
Keypad
Card Swiping Area
Doorbell Button
Emergency Power Supply Interface
Anti-Peephole Butto n
Lever Handle
Secure Knob
RESET Hole
Serial Port
Battery Slo t
Lever Handle
Mechanical Keyhole
Battery Cover
3
Lock Installation
Switch Lever Handle Direction (Optional)
1.Switch Lever Handle Direction
- Take off the rubber and remove the reversing screw with screwdriver.
- Rotate the lever handle 180 degrees upwards.
- Screw the reversing screw into the opposite screw hole.
Reversing Screw
2.Conrm Clutch Direction
- Front panel: Insert square rod into sleeve and lift lever handle. Rotate sleeve 90 degrees if lever handle idles.
- Rear panel: Turn on the anti-peephole button. Insert square rod into sleeve and lift lever handle. Rotate
sleeve 180 degrees if lever handle idles.
Square Rod
Front Panel Rear Panel
Elastic Cylinder Pin
Anti-Peephole Butto n
4
Switch Lock Latch Bolt (Optional)
1
2
3
Uplift the metal here.Rotate the latch bolt 180 degrees.
Turn the central part 90 degrees and
tuck it in.
Push the latch bolt into the lock
body.
Installation Steps
• The standard accessories for this product support installation for 40mm-50mm wooden doors. If
the thickness of the door is beyond this range, please contact your local dealer.
• When xing front and rear panel, do not press internal connection cable.
• When installing front and rear panel, handle with care in case of any panel damage.
1.Drill Hole
The product is applicable to wooden door and burglar-proof metal door. Drill hole in accordance with hole
templet in packing list.
Use installation paper template
to mark the size of the holes and
the center points.
5
2.Install
Please tap to watch the installation video.
1 Fix lock body into door panel with screws.
Install the lock body
and tighten the screws.
2 Insert square rod into front panel and install the front panel into door as shown below.
Pick up the front panel.
2.Insert the square rod.
3.Tighten the locating pins.
1.Place the locating pins.
6
3 Insert the front panel in the correct position and test normal operations of latch bolt and handle.
Insert the front panel in
the correct position.
4 Fix the xed plate and rubber pad into the door with ①locating pin and ② tighten sleeve.
Align the center of the
hole in the liner with the
square rod, and tighten
the screws.
5 Connect the front and the rear panels with the cable.
2
2
1
1
7
6
With the secure knob keeping upright, x the rear panel with screws as shown below.
Make sure the secure knob
is in the upright position,
and insert the rear panel.
7
Place the batteries into the rear panel.
Place the batteries.
8
Test your passwords, ngerprint and proximity card, and then the installation is nished.
Lock Settings
After installation, remove back cover of battery seat and install 4*AA-sized batteries. Then you can set the
lock as needed.
Please tap to watch the setup video.
• Please remove protective lm from lock before rst use.
• Please note that disinfectant may cause damage to the lock body.
8
Activate Lock
Touch keypad area to activate the lock.
Enter Menu
Press 3571# to enter menu.
• In initial state, enter short code for settings.
• In non-initial state, verify with administrator's ngerprint, password or card rst. Then enter short code for
settings.
Menu Index
Menu
11#
12#
13#
Add Fingerprint
Add Password
Add Card
21#
22#
23#
Delete Fingerprint
Delete Password
Delete Card
31#
32#
33#
Clear Fingerprint
Clear Password
Clear Card
41#
42#
43#
High Volume
Low Volume
Mute
3570# Initialize
After every successful setting, you will return to the menu. Then you can enter short code again to set
or press * to exit.
Add Fingerprint/Password/Card
Add Fingerprint
• The number of times will be displayed on the keypad each time you touch the ngerprint reader.
• Please remember your ngerprint number well in case you want to delete the ngerprint in the
future.
• Fingerprint which has been added cannot be added again.
9
1 After entering the menu, press 11# to add
ngerprint.
2 Touch ngerprint reader. Then touch again
after voice prompt and repeat the operation for
5 times to conrm. The ngerprint number will
ash on the keypad when complete.
Fingerprint Collection
When collecting ngerprint, please adjust your nger to maximize the ngerprint contact surface as shown
below, which helps to improve ngerprint verication success rate.
Add Password
• Please remember your password number well in case you want to delete the password in the
future.
• Password which has been added cannot be added again.
1 After entering the menu, press 12# to add
password.
2 Enter password (6 to 10 digits) and press #. Then
enter password and press # again to conrm.
The password number will ash on the keypad
when complete.
Add Card
• Please remember your card number well in case you want to delete the card in the future.
• Card which has been added cannot be added again.
1 After entering the menu, press 13# to add
card.
2 Swipe card. The card number will ash on the
keypad when complete.
10
Delete Fingerprint/Password/Card
Delete Fingerprint
The current veried ngerprint cannot be deleted.
For example, if you verify with ngerprint 1, then ngerpint 1 cannnot be deleted.
1 After entering the menu, press 21# to delete
ngerprint.
2 Enter ngerprint number and press #.
3 The ngerprint number ashes and then
press #.
Delete Password
The current veried password cannot be deleted.
For example, if you verify with password 1, then password 1 cannnot be deleted.
11
1 After entering the menu, press 22# to
delete password.
2 Enter password number and press #.
3 The password number ashes and then
press #.
Delete Card
The current veried card cannot be deleted.
For example, if you verify with card 1, then card 1 cannnot be deleted.
1 After entering the menu, press 23# to
delete card.
2 Enter card number and press #.
3 The card number ashes and then press #.
Indice
Altri manuali Ezviz Serratura
