Fagor LF065ITU Manuale utente
DISHWASHER
INSTALLATION AND FITTING
51
2
CONNECTION TO THE PLUMBING
aConnect the pipe to
the water inlet, tighten
the connection nut
and make sure it is
securely connected to
the appliance.
The water connection pipe is located on the back of the dishwasher:
a
UNPACKAGING
1
UNPACKAGING THE DISHWASHER
Remove the internal pro-
tection: polystyrene wed-
ges for holding the racks
firm.
Please refer to the specification label on the top edge of the door before making the electrical
connections. Make sure that the power voltage connected to the plug socket is as shown
on the label.
3
ELECTRICAL CONNECTION
Serial number
Model
The specifications label is on the top edge of the interior
of the door. This label must never be removed, since it
provides information about the exact model of the
dishwasher, required power supply, serial number and
warranty.
IMPORTANT
It is very important for
the dishwasher to be
connected to an earthed plug
socket. The electrical
installation, plug, socket,
fuses or circuit breaker and
meter must be capable of the
maximum power shown on
the specifications label. If the
power cable is damaged, it
must be replaced exclusively
by the manufacturers,
aftersales service (TAS) or
authorised personnel. If the
appliance is to be
recessmounted and
integrated, the plug must be
accessible after installation.
LF-65IT
The hose must run
between the wall and
the bottom space at
the back of the
dishwasher (b1) so
that it is not squashed
or overstretched.
There should be a fixed
water outlet drain at a
distance of between 25 and
100 cm from the floor. Make
sure that the outlet pipe is
not too rigid, bent or
squashed.
b
If your dishwasher has a hot
water inlet, connect the pipe
to the hot water tap. In t is
case, t e maximum
temperature must not
exceed 60ºC. Bear in
mind that this type of water
supply may affect the
washing and drying
capacity of the appliance.
max.
100 cm
min.
25 cm
It is very important for the bend pipe of the outlet hose is located securely in water outlet
so that it cannot disconnet. The operating water pressure (minimum and maximum) must
be between 0,5-10 bar (0,05-1 MPa).
IMPORTANT
b1 b2
4
LEVELLING AND POSITIONING
LEGS - LEVELLING
WORKTOP
If the worktop is
wooden, fit the plastic
protection onto it to
prevent the area from
being damaged by
steam.
Fit the front brackets to
the dishwasher so that
it can be fixed to
neighbouring units or
the work surface (see
point k, page 54).
a
b
c
d
e
ab
e
To flush-mount the
dishwasher in a row of
kitchen fittings sharing
the same plinth, loosen
and remove the base
accessories.
Before fitting the
dishwasher into the
space, raise it up to
the height of the
worktop by turning the
rear legs until a space
of some 3 mm is left
from the top.
Then adjust the front
legs to the desired
height. Some
integrated models
include a rod for
levelling the rear legs
from the front.
e
d
c
d
To install an integrated
dishwasher:
English
53
DOOR
An information template
is provided with the
assembly instructions.
Position the template, fix
it in place and mark the
position of the holes.
Drill the holes with a Ø
2.5 mm bit and screw the
supports to the panel with
the curved part facing
downwards.
Pick up the door panel and
fit the supports into the door
housing. Pull it downwards,
ensuring it is firmly fixed
and levelled with the top
part of the door.
Open the dishwasher door
slowly, holding the panel in
place, and then fix it with
the screws, ensuring the
panel is correctly aligned
with the door.
If the door springs are not
strong enough,
compensate the door
with the two additional
screws provided in the
accessories bag.
Fit the dishwasher into
the space. Adjust it to the
worktop until the top of
the dishwasher makes
contact with the bottom
of the kitchen fitting.
Fit the plinth in place,
sawing it to obtain the
desired measurement.
Fix the dishwasher to the
worktop, in the case of a
wooden worktop. If it is a
granite worktop, fix the
dishwasher to the
adjoining fittings.
f
The maximum and minimum recommended weights for
the door panel to be placed on the dishwasher
are:Maximum: 6.5 kg. Minimum: 3 kg.
IMPORTANT
i
j
k
l
A space of at least two millimetres must be left at the
sides between the kitchen fittings or electrical appliances
and the dishwasher.
IMPORTANT
h
gfg
h
An information template is
provided with the assembly
instructions.
lk
j
i
Integrated beneath a worktop
Column-integrated
50 114 mm
600
16
6
min. 25
82
58
9
English
55
b
Once the dishwasher has
been installed correctly, it
should be first used on
prewash programme:
Open the dishwasher
door.
Press the dishwasher
ON button.
Select programme 1
(prewash), with no
dishes or detergent.
Close the door. The
dishwasher will start
up automatically.
This is to check the
installation, the
connections and the drain
outlet, as well as to
completely wash the
interior before running a
wash pro-gramme
a
b
ca
c
PROG
d
d
5
PRE-WASH
USING THE APPLIANCE - A FEW PRACTICAL TIPS
DISHWASHER
57
Before starting up t e dis was er, you will need to know t e water ardness in
your area. You can find this out by either:
1º Consulting the local Water Board,
2º consulting the T.A.S. (Technical Assistance Service), or
3º using the Aquadur strip included in the accessories bag, following the instructions
below.
1
WATER HARDNESS, SALT, RINSE-AID AND DETERGENT
To find out the water hardness:
Place the strip in a glass of water
for one second, and then take it
out.
Shake it and wait for one minute.
The strip will show the water
hardness. Check the result of the
test against the table below. You
will probably need to adjust your
dishwasher.
a
b
c
If no salt needs to be added to your dishwasher, go straight on to the "rinse aid" section.
Water ardness adjustment. Water contains scale. The more scale, the harder the
water. To prevent the scale in the water from damaging the dishwasher, it is equipped
with a descaler to reduce the scale and leave it perfectly clean for washing. The descaler
uses salt to function.
b
1 min.
a
1 sec.
c
HF: Water hardness (French system) DH: Water hardness (German system).
Scale level (HF) 0-13 HF 14-38 HF 39-50 HF 51-63 HF Over 63 HF
Scale level (DH) 0-7DH 8-21 DH 22-28 DH 29-35 DH Over 35 DH
Test result
Green 1 Red stripe 2 Red stripes 3 Red stripes 4 Red stripes
No salt needed Position 1 Position 2 Position 3 Position 4
L0 L1 L2 L3 L4
Hardness Soft Standard Medium Hard Very hard
Dial
position
Manual
Electronic
RESERVOIR A SEL
The dishwasher has a salt container in the bottom of the
tub.
Important: use dishwasher salt only.
b
a
When the salt container needs filling,
you should always do it before a wash
and not afterwards. d
On some models, the salt regulator is
electric (has no numbers: (see Mod. C
in the photo) and is regulated from the
control panel.
These models have 5 regulation
positions.
1. Press the Time Delay button
and hold it down for three seconds. REGULATOR Model C
MANUAL REGULATION
If there is a salt regulator like the one
shown in the photographs (Mod. A-B)
inside your dishwasher on the right-hand
side, turn it to the number that
corresponds to the hardness of the water
in your area (see table).
To turn it to the correct position, use a
coin (Mod. A) or a screwdriver (Mod. B).
Controlling the salt level
Depending on the model, dishwashers
will have a manual or electronic salt level
control.
This simple adjustment of your dishwasher is vital
for its correct functioning. Do not ignore it.
ELECTRONIC REGULATION The letter “L” followed by a
number will appear on the
display (L1).
2. Press the Time Delay
button to select the
required salt level.
3. Validate the
selection (see table) using the
Programme button.
PROG
The first time you fill the salt container,
you must:
Pour in the salt but do not fill the
container to the top.
Top it up with water.
Stir with a spoon.
Close the lid tight and clean the salt
around the container.
a
b
c
d
REGULATOR Model B
REGULATOR Model A
WHERE TO PUT THE SALT
c
When do I need to
add salt?
A pilot light will come on
to show when more salt
needs to be added.
You should not use salt if your dishwasher does not need
it. In this case, the pilot light will remain on at all times.
IMPORTANT
English
59
The rinse-aid helps
drying and prevents
drops of water from
clinging to utensils after
washing. The rinse-aid
container is located on
the inside of the door, next
to the detergent container.
It has a 4-position
dispenser for adjusting
the amount of rinse-aid to
the water quality (the
dispenser is set at
position 2 at the factory).
If you notice drops of
water on utensils,
increase the position of
the rinse-aid dispenser. If
the utensils have white or
sticky lines, lower the
position.
RINSE-AID CONTAINER
DISPENSER
a
Once the level of the
dispenser has been
set, fill the container
to the top, but do not
overfill it. If this
occurs, clean the
spillage with a cloth.
a
A greater amount of rinse-aid does not necessarily mean
better results. In fact, too much rinse-aid can lead to
water marks.
IMPORTANT
When do I need to
add rinse-aid?
The dishwasher itself will
inform you of when the
rinse aid needs refilling.
A pilot light on the design
panel will come on when
a refill is necessary.
PILOT LIG T
PILOT LIG T
Important:
If your dishwasher
does not have a display or
pilot light, you should
periodically refill the salt
that has been used (about
every 20 washes for
medium-hard water).
b
aPour in the detergent,
then close the tank
cap.
Some programmes
also require part of the
dose of detergent to be
poured into the tank
cap compartment.
Detergent comes in tablet,
powder and liquid form.
You can consult the amount
of detergent needed on the
programme chart.
Detergent
The detergent is poured into a tank on the inside of the door, beside the rinse aid tank.
If you use detergent tablets instead of traditional products (granulated salt, powder detergent,
liquid rinse aid), you may notice a loss of efficiency, particularly in the case of short programmes
and/or programmes with low wash temperatures.
If you notice any performance problems with your dishwasher, e.g. there is a white film on the tank
or on the dishes, an accumulation of scale or poor drying efficiency, you should go back to using
traditional products.
We would remind you that if you go back to using traditional granulated salt, you will need to run a
few programmes before the dishwasher performs perfectly again, and there may still be some residue
left on the tank and dishes.
If you wish to use combined tablet products, read the instructions and indications for use on the
packet carefully.
In case of doubt, consult the cleaning product manufacturer.
We provide no guarantee for any complaints directly related to the use of this type of products.
b
DETERGENT CONTAINER
a
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Fagor Lavastoviglie
Fagor
Fagor AD - 21 W Manuale utente
Fagor
Fagor 3LVF-421 Manuale utente
Fagor
Fagor EVOconcept CCO-120DCW Guida rapida
Fagor
Fagor 3LVF-638IT Manuale utente
Fagor
Fagor CO-500 Manuale utente
Fagor
Fagor IO-DWS-2841 Manuale utente
Fagor
Fagor LVC-21W Manuale utente
Fagor
Fagor EVO CONCEPT CO-502 Guida all'installazione
Fagor
Fagor 3LVF-435 Manuale utente
Fagor
Fagor LFA-073 IT Manuale utente
Fagor
Fagor LFA-75IT Manuale utente
Fagor
Fagor 3LVF-622IT Manuale utente
Fagor
Fagor 3LVF-438ADX Manuale utente
Fagor
Fagor 3LVF-423 Manuale utente
Fagor
Fagor 3LVF-624IT Manuale utente
Fagor
Fagor HDWF-CL Manuale utente
Fagor
Fagor LVE-55 Manuale utente
Fagor
Fagor AD-48BDD Manuale utente
Fagor
Fagor FI - 48 W Manuale utente
Fagor
Fagor Eco Concept CDT-600 Manuale utente
