Specifications
Motor 230V, 50Hz, 85 Watts
Rpm 4,800
Vice Capacity 0.80" to 0.50"
Table Vice Angles 35 Degrees Right to Left
Arbor Diameter 22mm (7/8")
Wheel Dimensions 115 Dia. x 3mm Thick (41/4" x 1/8")
Overall Dimensions W 230 x L 250 x H 308mm ( 9" x 10" x 121/8")
Weight 2kg (4.85lbs)
Save this manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep the manual in a safe
and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tools, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
READ ALL THE INSTRUCTIONS BEFORE USING THIS TOOL
1. Keep the work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or
wet locations. Don't expose to rain. Keep the work area well lit. Do not use electrically
powered tools in the presence of flammable gasses or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let them
handle machines, tools, or extension cords.
4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit
rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or attachment to do
the work of a larger industrial tool. There are certain applications for which this tool was
designed. It will do the job better and more safely at the rate for which it was intended.
Do not modify this tool and do not use this tool for a purpose for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewellery as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-slip footwear are
recommended when working. Wear restrictive hair covering to contain long hair
7. Use eye and ear protection. Always wear approved impact safety goggles. Wear a full
face shield if you are producing metal filings or wood chips. Always use a BS or EN
approved safety products, we recommend Scan Safety Products, information available
at www.scan-safety.com.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines.
Page 2
8. Lock the chain in the Sliding Guides(31)
by turning the Handle (34).
See FIGURE 8.The Handle (34) should
be situated so that you can easily release
and tighten it. You will need to release
it each time you move to the next link,
and tighten it to sharpen each link.
9. If the chain has been repeatedly
sharpened, the chain depth limiting
gauges may need to be taken down with
a flat file (not included).
See FIGURES 8 & 9. File down each
gauge so that they are at a lower level
than cutting teeth.
Sharpening
1. Always wear appropriate clothing and suitable eye protection and make sure the
immediate area is clear of bystanders.
2. Plug in the Power Cord (3) and press the green button on the Switch Plate (5) to
turn on the machine.
3. Slowly lower the grinding wheel as shown in FIGURE 10. If you notice slight errors in
your settings, turn off the unit and unplug it before you make your adjustments.
Note: A good grind occurs when the
contact between the wheel and the teeth
are gradual and smooth. Do not stop too
long on each tooth.
4. After sharpening one tooth, turn off the
machine. Lift the Top Housing (4),
release the Handle (34), and move the
chain so that the next link is positioned in
the Chain Stop (23). Tighten the Handle
(34). Turn the machine back on and
continue sharpening the next tooth. Repeat
this process until you have sharpened all
of the links set up for this angle.
Page 7
FIGURE 8
FIGURE 9
FIGURE 10
Handle
(34)
Limiting
Gauge
Operation (continued)
Chain Stop (23)
