F&F SCO-815 Manuale utente
- 1 -
SCO-815
Lighting dimmer,
universal
The SCO-815 universal lighting dimmer allows the brightness of
the following light sources to be adjusted:
»Incandescent and halogen lamps of the main series (resistive
load R);Lamps supplied by a toroidal transformer (inductive
load L);
»Lamps supplied by an electronic transformer (capacitive load
C);
»Energy-saving compact fluorescent lamps (ESL) with dimming
function;
»Energy-saving led lamps (LED) with dimming function.
Purpose
F&F Filipowski L.P.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collec� on, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.
- 2 -
»Automatic detection of the nature of the load: R+L, R+C and
LED. The use of ESL lamps requires manual setting of the na-
ture of the load using the knob on the face of the dimmer;
»Smooth brightening and dimming to extend the life of the con-
trolled lamp;
»Adjustable brightening and dimming rates;
»„Memory” of light intensity settings – after each switch-on,
the lighting returns to the previously set brightness. Not ap-
plicable to ESL lamps;
»Adjustment of the minimum illuminance level of the control-
led lamp (especially important for ESL lamps, requiring mini-
mum ignition and holding current);
»ON mode – switching of the lighting to maximum brightness
without dimming;
»Control input galvanically isolated from the dimmer supply
circuit.
The lighting can be controlled by a number of pushbuttons con-
nected in parallel and located at different points in the room.
The receiver is switched on to the last set brightness level after
a current pulse caused by pressing any momentary (bell) button
connected to the relay. A short press of the button switches the
lighting on. Pressing and holding the button (for more than 1 se-
cond) changes the brightness level in one direction (brightening
or dimming). Each time the button is pressed again (for more
than 1 second), it adjusts in the opposite direction.
Features
Functioning
- 3 -
"S"setting
»ON – switching of the lighting to maximum brightness without
the possibility of dimming;
»MIN-MAX – adjustment of lighting and dimming speed of the
controlled lamp (for R, L, C and LED characteristics);
»ELS (+/-) – adjustment of lighting and dimming speed for ELS
lamps only. Two setting levels: (+) – faster; (-) – slower.
"%"setting
»MIN-MAX – setting of the minimum light level of the control-
led lamps. Especially for ELS lamps, where in the lower ranges
of illumination there may be a flickering effect or no illumi-
nation at all.
1. Disconnect the power supply.
2. Place the dimmer on the rail in the switchboard.
3. Power supply to the dimmer: connect phase L to terminal 10;
connect N wire to terminal 8 (7 or 9).
4.Control buttons: connect a single button or a group of parallel
connected buttons between phase L (+) and terminal 1; con-
nect the N or (-) wire to terminal 3.
5.Connect controlled lighting between terminal 12 and N wire.
Settings
Mounting
- 4 -
SCO-815 can work with backlit buttons.
In the case of frequent overheating of the system, redu-
ce the load (the number of receivers or their power) or
ensure better ventilation.
The control input is galvanically isolated from the power
supply of the dimmer.
Possibility of connecting a separate control voltage, dif-
ferent from the supply voltage.
Terminals 7-8-9 are connected to each other and consti-
tute a common point N.
In some cases, the dimmer and the light source may not
work properly (for example the light may flicker). This
often occurs with a small load on the dimmer and the
solution is usually to increase the load by, for example,
attaching additional bulbs.
The load on the dimmer’s output cannot exceed the li-
mit values. Values given for individual lamps in the tech-
nical data in the manual.
Testing is recommended before final installation.
1-3 control input
7-8-9 N power supply
10 L power supply
12 dimmer’s ouput
Wiring diagram
- 5 -
Testing is recommended before final installation.
1-3 control input
7-8-9 N power supply
10 L power supply
12 dimmer’s ouput
Wiring diagram
E230329
power supply 195÷265 V AC
maximum load current (AC-1) 2 A
maximum power of connected light bulbs
(R) 500 W
(L) 500 W
(C) 500 W
(ESL) 100 W
(LED) 100 W
control voltage 9÷230 V AC/DC
power consumption 0.1 W
terminal 2.5 mm² screw terminals
tightening torque 0.4 Nm
working temperature -25÷50°C
dimensions 1 module (18 mm)
mounting on TH-35 rail
ingress protection IP20
The F&F products are covered by a warranty of the 24 months
from the date of purchase. Effective only with proof of purchase.
Contact your dealer or directly with us.
F&F Filipowski L.P. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE.
The CE Declaration of Conformity, along with the references to
the standards in relation to which conformity is declared, can be
found at www.fif.com.pl on the product page.
Technical data
Warranty
CE declaration
Indice
Altri manuali F&F Dimmer
