Fantec DB-R35DUS Manuale utente
DB-R35DUS
User Manual
English
Detail View:
Front View:
1. Power indicator
2. Rebuild indicator
3. HDD1 Access Indicator
4. HDD2 Access Indicator
5. HDD1 Error Indicator
6. HDD2 Error Indicator
7. Ventilation
USB 2.0
Rare View:
1. Power switch
2. Power receptacle
3. USB 2.0 port
4. Fan for ventilation
RAID Jumper Setting:
None RAID
(Single Mode)
1 4
2 5
3 6
RAID0
Spanning
1 4
2 5
3 6
RAID0
Stripping
1 4
2 5
3 6
RAID1
Mirroring
1 4
2 5
3 6
1. When both HDD insert at the same time under RAID mode all data will be
formatted.
2. For the first time usage, please install one main source HDD and power “on”
DB-R35DUS. Wait until “error”indicator on the second HDD lights on, system had
set first HDD to Main HDD then power “off”DB-R35DUS. Please install second
HDD and power “on”again. System will automatically “rebuild” data to second
target HDD. (If both HDDs are new with no data, then both HDDs can install at the
same time.)
3. Both HDDs have to be the same brand and model number when using “RAID
function”.
4. When changing usage mode (Single Mode, RAID0 Mode or RAID1 Mode) will
require re-format the HDDs. Make sure back-up all data before doing so.
System Requirements
PC Requirements
•Minimum Intel Pentium III CPU 500MHz, 128MB RAM
•USB 1.1 equipped PC; Win2000, WinXP, Vista
•USB 2.0 equipped PC; Win2000, WinXP, Vista
Mac Requirements
•Minimum Apple G3 processor (G4 for 1394b), 128MB RAM
•USB 1.1 equipped Mac; Mac OS 9.2, 10.1.5 or above
•USB 2.0 equipped Mac; Mac OS 10.2 or above
Package Contents
•RAID enclosure X 1
•External Power Adapter; Input 100-240V, Output +12V/2A, +5V/2A X 1
•Power Cord X 1
•Interface Cables:
USB2.0 X 1
•Screw Driver X 1
•Accessories pouch (screws) X 1
Hard Drive Assembly:
1. To remove the cover of
DB-R35DUS:
Please unscrew and
remove the screws on the
bottom of unit. Only one
side (top) of screws needs
to remove. Top side is the
side where power switch is.
Insert the screw-driver into
the bolt and push upward
to release the top cover.
2. Unfasten the screws on
HDD holder case and pull
backward to release the
HDD holder case.
Since using RAID1 (Mirror Mode) if install improperly, the HDD which already
contain DATA will be formatted. To prevent Data lost please follow step 3-1 for
installing under RAID 1 (Mirror Mode)
Installing Single or RAID0 Mode:
3. Insert both HDD1 and HDD2 into
both bays of HDD holder and secure
them with screws.
4. Insert back the HDD holder back to DB-R35DUS
with both HDDs attached.
5. Push forward the HDD holder to secure the
connection and fasten the screws on the holder.
6. Recover the top plate of DB-R35DUS and fasten
the screws prior remove.
Now installation is complete, please attach power core and connect DB-R35DUS
with USB cable to computers. DB-R35DUS is ready to use.
Installing RAID1 Mode:
Installing this method, if first HDD already contain data.
Note: Two HDD must be identical in brand, size and model number.
3-1. Insert first HDD which contain data.
And fasten with screws.
3-2. Insert back the HDD holder back to DB-R35DUS
with first HDDs attached. Make sure the
connection of HDD holder and DB-R35DUS is
intact.
At this point, please connect DB-R35DUS to power source and turn on the unit. (no
need to connect to computer.) DB-R35DUS will automatically build a RIB table to
First HDD. This way is for DB-R35DUS to recognize the source HDD. After the RIB
table is written on to HDD, the error light indicator of second HDD will light. Power off
and remove the HDD holder to install the second HDD.
3-3. Please insert second HDD and
secure it with screws.
3-4. Push forward the HDD holder to secure the
connection and fasten the screws on the holder.
3-5. Recover the top plate of DB-R35DUS and fasten
the screws prior remove.
Now installation is complete, please attach power core. After turn on the unit,
DB-R35DUS will perform “REBUILT”function. This copies an identical data from
HDD1 to HDD2. Rebuilt can be done off-line. After Rebuilt indicator LED goes off and
DB-R35DUS is ready to use. Rebuilding data might take several hours depend on
the capacities of HDDs.
System Setup:
Connection to your computer:
Few cautions before using RAID enclosure
1. Do not cover or block the ventilation holes on the enclosure.
2. Check for visible damage on unit, accessories and cables before tuning on the
power.
3. Do not expose the enclosure to water and humid conditions.
Setting Mode:
None-RAID: (Single Mode) Computer will show up as two independent drives. This
function can be use if only one HDD is installed. Or, two different brands orcapacities
of HDDs are installed.
RAID0 - Spanning: Two HDDs will show up as one large single drive. Spanning is an
array (not RAID) that is written sequentially across two drives.
RAID0 -Stripping: Two HDDs will show up as one large single drive but speed
performance will boost up. The two HDDs will write Data in “column”effect. This form
of array splits each piece of Data across both HDDs in segments. Data are store
between first HDD and second HDD. While the HDD is stripe in writing, the next head
of next HDD is move to next track to write. The Data is writing without any form of
data-checking. Once one HDD is damage and all Data can be lost.
RAID1 –Mirroring: Using this mode will require 2 identical HDDs; meaning they
must be the same capacity, brand and model number. Under RAID1, it will create an
extra copy (or mirror) set of data to second drive. The backup data are more
important for safe keeping and the available data only show up in one large single
drive. This is useful when first HDD fail and it can be replaced by second set of
identical data instantly.
Indice
Altri manuali Fantec Magazzinaggio
Fantec
Fantec DB-228U3 Manuale utente
Fantec
Fantec QB-X2US3R Manuale utente
Fantec
Fantec MD-26U3 640GB Manuale utente
Fantec
Fantec SQ-X2RU3e Manuale utente
Fantec
Fantec SQ-35U3e Manuale utente
Fantec
Fantec MR-35DU3 Manuale utente
Fantec
Fantec SQ-35U3e Manuale utente
Fantec
Fantec MR-2535DUAL Manuale utente
Fantec
Fantec MR-35US3R Manuale utente
Fantec
Fantec MD-26U3 500GB Manuale utente
