Recommended Maintenance
1. Since fan bearings are sealed and provided with an internal lubricating mate-
rial, no additional lubrication is necessary.
2. Fan impeller may accumulate lint. Periodic inspection, based upon dryer
usage, should be performed to ensure that the fan impeller is not
obstructed or loaded with lint. Under normal conditions, fan should be
inspected a minimum of every Six (6) Months.
Note: Excessive booster fan
noise or vibration may be an indication of lint buildup on the impeller.
To
inspect and clean the impeller:
a. Disconnect the incoming power supply at the source.
b. Remove the duct from the fan inlet and remove any lint buildup on
the impeller.
c. Reconnect the duct to the fan. Turn power supply on.
Troubleshooting
Important Notice: Prior to performing Steps 1 - 3, be certain that the
electrical supply to the fan/switch is turned off.
If fan fails to start when the dryer cycle begins, please follow the pro-
cedure listed below:
1. Check the incoming supply for proper voltage.
2. Turn on the electrical supply and restart the dryer cycle. Check to be certain
that fan starts.
If fan still fails to start after performing Steps 1 - 4, continue
following the procedure as listed below:
3. Verify that the pressure switch diaphragm is vertical as illustrated on Page 2
of these instructions. If the diaphragm is not vertical, reposition the pressure
switch and check for fan operation against another dryer cycle.
4. Verify that the tubing is not crimped and that the tubing connector
nipples are not obstructed.
5. If switch diaphragm is vertical and fan still fails to start, with the
electrical supply on:
a. Remove the tubing from the nipple on the fan and blow gently into
the tubing;
b. If fan starts, consult Fantech for additional technical support.
c. If fan fails to start, please consult Fantech for additional
technical support.
Fantech, reserves the right to modify,at any time and without notice,
any or all of its products’ features, designs, components and specifica-
tions to maintain their technological leadership position.
Item #: 401315 • Rev Date: 100406
United States
1712 Northgate Blvd.,
Sarasota, FL. 34234
Phone: 800.747.1762; 941.309.6000
Fax: 800.487.9915; 941.309.6099
Canada
50 Kanalflakt Way,
Bouctouche, NB E4S 3M5
Phone: 800.565.3548; 506.743.9500
Fax: 877.747.8116; 506.743.9600
FIVE (5) YEAR WARRANTY
This warranty supersedes all prior warranties
DURING ENTIRE WARRANTY PERIOD:
FANTECH will repair or replace any part which has a factory defect in
workmanship or material. Product may need to be returned to the fantech
factory, together with a copy of the bill of sale and identified with RMA
number.
FOR FACTORY RETURN YOU MUST:
Have a Return Materials Authorization (RMA) number. This may be
obtained by calling FANTECH either in the USA at 1.800.747.1762 or in
CANADA at 1.800.565.3548. Please have bill of sale available.
•The RMA number must be clearly written on the outside of the carton,
or the carton will be refused.
•All parts and/or product will be repaired/replaced and shipped back to
buyer; no credit will be issued.
OR
The Distributor may place an order for the warranty part and/or product
and is invoiced. The Distributor will receive a credit equal to the invoice
only after product is returned prepaid and verified to be defective.
FANTECH WARRANTY TERMS DO NOT PROVIDE FOR REPLACEMENT
WITHOUT CHARGE PRIOR TO INSPECTION FOR A DEFECT. REPLACE-
MENTS ISSUED IN ADVANCE OF DEFECT INSPECTION ARE INVOICED,
AND CREDIT IS PENDING INSPECTION OF RETURNED MATERIAL.
DEFECTIVE MATERIAL RETURNED BY END USERS SHOULD NOT BE
REPLACED BY THE DISTRIBUTOR WITHOUT CHARGE TO THE END
USER, AS CREDIT TO DISTRIBUTOR'S ACCOUNT WILL BE PENDING
INSPECTION AND VERIFICATION OF ACTUAL DEFECT BY FANTECH.
THE FOLLOWING WARRANTIES DO NOT APPLY:
•Damages from shipping, either concealed or visible. Claim must be
filed with freight company.
•Damages resulting from improper wiring or installation.
•Damages or failure caused by acts of God, or resulting from improper
consumer procedures, such as:
1. Improper maintenance
2. Misuse, abuse, abnormal use, or accident, and
3. Incorrect electrical voltage or current.
•Removal or any alteration made on the FANTECH label control number
or date of manufacture.
• Any other warranty, expressed, implied or written, and to any consequen-
tial or incidental damages, loss or property, revenues, or profit, or costs
of removal, installation or reinstallation, for any breach of warranty.
WARRANTY VALIDATION
•The user must keep a copy of the bill of sale to verify purchase date.
•These warranties give you specific legal rights, and are subject to an
applicable consumer protection legislation. You may have additional
rights which vary from state to state.
