Fanvil ATA Manuale utente
ATA Gateway
Quick Installation Guide
V1.0
Status indicator
Ethernet Cable
Quick Installation GuideATA Gateway
Power Adapter
Packaging list
Po
Ne
SI
reg
FX
Po
ork
Icon
On: Power
supply is normal
On: connection
is normal
On: registration
is successful
Function
Off: Power is
invalid
Off: not
connected
Off: SIP is
not registered
Off: N/A On: Phone is
being off hook
wer
twork
Pistration
S
rts
Twinkle: netw
fai lure
Twinkle:
registration is failed
Icon
Power DC 5V IN
Network WAN
FXS FXS
Reset RST button (6 seconds) with a sharp object
(such as a pencil) until the LED fast twinkling.
Restore function will take effect after you
release it.
Function
Connecting to a power source to the
micro-USB or DC Jack
Connecting to the network.
Connecting to the analog phone.
Restore Default button. When the
device is working properly, if you press this
Ports
Device ports
RST
DC 5V IN DC 5V IN WAN
FXS
Device connection
Connect your device, please follow the steps below:
1．Insert a standard RJ11 telephone cable into the FXS port and
connect the other end of the telephone cable to a standard touch-tone
analog telephone.
2．Insert the ethernet cable into the WAN port of the device and
connect the other end of the ethernet cable to an uplink port (a router
or a modem, etc.)
3．Insert the power adapter into the device and connect it to a wall
outlet.
4．The power and ethernet LEDs will be solidly lit when the device
and network is ready for use.
Configuration
Configuration via web
1．Connect the computer to the same network as your device and
make sure the device is booted up.
2．Use a telephone connected to FXS port of your device.
3．You may check your device IP address using input the
corresponding voice menu numbe on the connected phone.
4．Open the Web browser on your computer.
5．Login: Input the IP address in the web browser. The PC and phone
should be in the same IP address segment (The default username and
password are both ‘admin’.)
6．Configure: Select network/account etc, and fill the relevant content.
7．Save the configuration.
Configuration via voice menu number of device
1．Use a telephone connected to FXS port of your device.
2．Set by inputting the voice menu number through phone.
3．The list of voice menu numbers is shown below：
Function Number Function Number
Start Reboot #**** Busy Call
Forward #*91
Enable Static
Mode #*100 No Ans Call
Forward #*92
Enable DHCP
Mode #*101 Always Call
Forward #*93
Enable PPPOE
Mode #*102 Voice Mail #*86
Read WAN IP #*111 Call Back #*87
Read Phone
Number #*222 Redial #*88
Set WAN IP
Addr #*50 DND ON #*94
Set WAN
Gateway #*51 DND OFF #*95
Set WAN DNS #*52 Blind Transfer #*27
Set WAN
Subnet Mask #*53 Attended
Transfer #*28
Disabled Call
Forward #*90 Conference(Co
nf) #*29
Indice
Altri manuali Fanvil Portale
Fanvil
Fanvil PA2S Manuale di installazione e d'uso
Fanvil
Fanvil G100S Manuale utente
Fanvil
Fanvil GA10 Manuale utente
Fanvil
Fanvil PA3 Manuale utente
Fanvil
Fanvil A2 Manuale operativo
Fanvil
Fanvil G200S Manuale utente
Fanvil
Fanvil PA3 Manuale utente
Fanvil
Fanvil PA2S Manuale utente
Fanvil
Fanvil LINKVIL W712 Manuale utente
Fanvil
Fanvil A1 Manuale utente
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
