Fanvil X3S Basic Guida rapida
Call Completion Function
and Configuration
Description
Version: <1.1>
Release date: <2018-05-08>
Contents
Contents......................................................................................................................................... 1
1Introduction......................................................................................................................... 2
1.1 Overview .................................................................................................................... 2
1.2 Applicable Models...................................................................................................... 2
2Function Description .......................................................................................................... 3
3Configuration Description ................................................................................................. 4
4Operation Description........................................................................................................ 6
4.1 Peer Telephone Set Is Busy (Call Waiting Disabled).................................................. 6
4.2 Peer Telephone Set Rejects Call (Reject Response Code 486)................................... 7
1 Introduction
1.1 Overview
When the called party of a call is busy or rejects the call, the local telephone set prompts the user
to call back manually or cancel the call.
1.2 Applicable Models
This document applies to Fanvil X3S and X4. The X5S and X6 models do not support the call
completion function.
2 Function Description
If the call completion function is enabled, signaling auto redial is enabled. If the called party is
busy or rejects the call (reject response code 486), the telephone set displays the messages "Call
completion. Wait xxx" and "Call completion. Call xxx" and determines whether the peer
telephone set is in the standby state (the peer telephone set is in the terminated state if it sends
NOTIFY). The user then determines whether to manually call back or cancel the call.
If the call completion function is disabled, the telephone set does not display the "Call
completion. Wait xxx" or "Call completion. Call xxx" message.
3 Configuration Description
1. The call completion function is configured in the <TELE CONFIG MODULE> module of the
configuration file.
Parameter
Description
P1 Call Complete
Call completion function. If the value is 1, when the peer telephone set
switches from the busy state to the idle state, the local telephone set
prompts the user to call back manually or cancel the call. If the value is
0, the call completion function is disabled. (The X5 and X6 series
telephone sets do not support the call completion function, and
therefore the default value is 0 in their configuration files. In the
configuration files of the X3 and X4 series telephone sets, the default
value is 0, indicating that the call completion function is disabled.)
2. To enable or disable the call completion function on the webpage, choose Phone Settings >
Features > Common Settings, select or deselect Enable Call Completion to enable or disable the
function.
3. To enable or disable the call completion function on the LCD, choose Menu > Features > Call
Completion,
click Enter and then select Enabled or Disabled to enable or disable the function.
4 Operation Description
4.1 Peer Telephone Set Is Busy (Call Waiting Disabled)
1. On the webpage of the test telephone set, choose Phone Settings > Features > Common
Settings and select Enable Call Completion. Alternatively, choose Menu > Features > Call
Completion on the LCD of the test telephone set, select Enabled, and click Save. Disable call
waiting for the peer telephone set B.
2. B is in a call with C. The test telephone set calls Bin hands-free, handle, or headset mode. The
test telephone set displays the message "Call Completion. Wait xxx", as shown in the following
figure.
3. In the dialog box prompting "Call Completion. Wait xxx":
(1) If you click Exit, the test telephone set exits the screen prompting "Call Completion. Wait
xxx" and returns to the standby screen. When B ends the call or is idle, the test telephone set
does not display the message "Call Completion. Call xxx".
(2) If you click OK, the test telephone set exits the screen prompting "Call Completion. Wait
xxx" and returns to the standby screen. When B ends the call or is idle, the test telephone set
displays the message "Call Completion. Call xxx" (xxx indicates the phone number of B) in
about 30s, as shown in the following figure.
Click Exit. The test telephone set does not call B and returns to the standby screen.
Click OK and capture SIP packets. It is found that the peer telephone set sends NOTIFY,
indicating that it is in the terminated state. At this time, the test telephone set can call B again and
set up a normal call.
4.2 Peer Telephone Set Rejects Call (Reject Response Code 486)
1. The call completion function is enabled for the test telephone set. The reject response code is
set to 486 (busy here) for the peer telephone set.
2. The test telephone set calls B in hands-free, handle, or headset mode. B rejects the call. The
test telephone set displays the message "Call Completion. Wait xxx" (xxx is the phone number of
B), as shown in the following figure.
3. In the dialog box prompting "Call Completion. Wait xxx" (xxx is the phone number of B):
(1) If you click Exit, the test telephone set exits the screen prompting "Call Completion. Wait
xxx" and returns to the standby screen. When B ends the call or is idle, the test telephone set
does not display the message "Call Completion. Call xxx".
(2) If you click OK, there are two cases:
a) If B is already in a call, the test telephone set calls B, and B rejects the call, the test telephone
set exits the screen prompting "Call Completion. Wait xxx" and returns to the standby screen.
When B ends the call, the test telephone set displays the message "Call Completion. Call xxx"
(xxx indicates the phone number of B) in about 30s.
b) If B is idle, the test telephone set calls B, and B rejects the call and returns to the idle state, the
test telephone set exits the screen prompting "Call Completion. Wait xxx" and soon displays the
message "Call Completion. Call xxx" (xxx indicates the phone number of B), as shown in the
following figure.
Click Exit. The test telephone set does not call B and returns to the standby screen.
Click OK and capture SIP packets. It is found that the peer telephone set sends NOTIFY,
indicating that it is in the terminated state. At this time, the test telephone set can call B again and
set up a normal call.
Altri manuali per X3S Basic
4
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Fanvil Telefono IP
Fanvil
Fanvil X6U Manuale utente
Fanvil
Fanvil X210i Manuale utente
Fanvil
Fanvil X3S Basic Manuale utente
Fanvil
Fanvil X7 Manuale utente
Fanvil
Fanvil F52 Manuale utente
Fanvil
Fanvil C58 Manuale utente
Fanvil
Fanvil X2P Manuale utente
Fanvil
Fanvil X7A Manuale utente
Fanvil
Fanvil X3U Pro Manuale utente
Fanvil
Fanvil C62 Manuale utente
Fanvil
Fanvil D900 Manuale utente
Fanvil
Fanvil V Series Manuale utente
Fanvil
Fanvil X5 Manuale utente
Fanvil
Fanvil VH05 Manuale utente
Fanvil
Fanvil X5S Manuale utente
Fanvil
Fanvil C66 Manuale utente
Fanvil
Fanvil X6U Manuale utente
Fanvil
Fanvil C56 Manuale utente
Fanvil
Fanvil H2S Manuale utente
Fanvil
Fanvil FNVL-X6 Manuale utente
