FASTRON. S-S Series Manuale per l'uso e la cura
1
S-S series SCR Power controllers 0-10V /0-5V input
signal calibration process
Change the two chip resistors R38 and R41 in the PCB board to 22K and 6.2K
respectively, connect R38 and R39 (far away from the two ends of the C16 chip
capacitor). As shown below:
(将PCB 板中 R38 R41 两个贴片电阻分别改为 22K 和6.2K，再将 R38 和
R39(远离 C16 贴片电容的两端)链接起来。如下图所示 )：
2. Software: 0-10V input signal calibration
the PCB board, the signal source (0-10V) is connected to the + /- two terminals of
the PCB board, as shown in the figure below
(将220V 交流电源接在 PCB 板AC1,AC2 两个端子上,信号源(0-10V)接在 PCB
板 + - 两个端子上，如下图所示):
2.1. Connect the 230V AC power supply to the two terminals AC1 and AC2 on
1. Hardware : changes on PCB board requitred for 420mA/020mA/POT to Linear Voltage
.
Set LCK = 169, Press and hold Enter Button for 3 seconds, then set
SET0 = 0000. Press and hold ENT button for 3 seconds
To open input configuration menu please ENT + DOWN KEY together
2
2.2 . Press the "ENT key and the down key" at the same time to enter the INP
parameter layer and change the INP parameter to 0-10. As shown below
(同时按下“ ENT 键和下键” 进入 INP 参数层并将 INP 参数改为 0-10。如下
图所示)
2.3. After pressing the ENT key to enter the next parameter "ANL", the signal
source is given a 0V signal. Press the < button one time, the OUT layer
blinking, then press the UP button and Down button one time respectively, and
press the ENT button to lock (this action is repeated twice). As shown below
(在按 ENT 键进入下个参数 “ANL”，信号源给入 0V 信号。先按左键，OUT
层显示闪烁，分别按一下上键和下键，再按 ENT 键锁定(此动作重复两次)。
如下图所示):
3
2.4. After pressing the ENT key to enter the next parameter "ANH", the signal
source is given a 10V signal. Press the < button one time, the OUT layer
blinking, then press the UP button and Down button one time respectively, and
press the ENT button to lock (this action is repeated twice). As shown below
(在按 ENT 键进入下个参数 “ANH”，信号源给入 10V 信号,先按左键，OUT
层显示闪烁，分别按一下上键和下键，再按 ENT 键锁定(此动作重复两次)。
如下图所示):
2.5 . Press ENT to enter the next parameter "LSP" and set this parameter to 0
(default), then press ENT to enter the next parameter "USP" and set this
parameter to 10 (default), as shown below
(按ENT 键进入下个参数“LSP”将此参数设为 0(默认),再按 ENT 进入下个
参数“USP”将此参数设为 10(默认).如下图所示):
4
2.6 . End of calibration.到此校验完成
3. Inspection and shielding (检验和屏蔽)
3.1 Inspection: After completing the above one and two steps, then to
check signal input correctly. The inspection process as follows :
3.1.1. The signal sources are fed with 0 V /5V /10V signals
- The "IN" layer of the PCB board is displayed 0 /5 /10 respectively.
- The "OUT" layer of the PCB board is displays 0 /50 /100 respectively .
3.1.2 . If the above operation finished , the 0-10V signal input inspection is
correct.
As shown below :
检验 ：完成以上 一 二两个步骤后进行信号输入检验。检验过程如下
信号源分别给入 0 V 5V 10V 信号
PCB 板显示板“IN”层分别显示 0 5 10
PCB 板显示板“OUT”层分别显示 0 50 100
复合以上条件则 0-10V 信号输入校正正确。
如下图所示
5
3.2 Shielding 屏蔽
3.2.1 Press the ENT key and the UP key at the same time to enter the DLY
parameter layer, find LOCK and set it to 169, as shown below
(同时按 ENT 键和上键进入 DLY 参数层，找到 LOCK 并将其设为 169，
如下图所示):
3.2.2 Press the ENT key for seconds to enter the SET0 layer parameters and
set SET0 to 0001. As shown below (长按 ENT 键进入 set0 层参数 并将 set0
设为 0001, 如下图所示)
6
3.2.3 Return to the DLY layer key, set the LOCK parameter to 0 , end of
shielding . (返回 DLY 层键将 LOCK 参数设为 0 屏蔽结束)
Indice
Altri manuali FASTRON. Controllori
FASTRON.
FASTRON. Meridian MEC-110 Manuale utente
FASTRON.
FASTRON. MERIDIAN Series Manuale utente
FASTRON.
FASTRON. Meridian MEC-110 Manuale utente
FASTRON.
FASTRON. VC-210 Manuale utente
FASTRON.
FASTRON. VISION VC-220 Manuale utente
FASTRON.
FASTRON. VISION Series Istruzioni operative
FASTRON.
FASTRON. VC-210 Manuale utente
FASTRON.
FASTRON. FTM1 Series Manuale utente
FASTRON.
FASTRON. F330 Series Manuale
FASTRON.
FASTRON. VC-210 Manuale utente
