FBI XL1218R Manuale utente

USER’SGUIDE TO

,, OPERATION

and

THE “USER-FRIENDLY”

XL1218R ,

Total Control at Your Fingertips!

. . *

;r -.

XL1218 USER’SGUIDE

INTRODUCTION

The “brain” of your new security system is the XL1218 Control Panel.

All of the detection devices of your system are wired to the control

panel. When a violation occurs, the control panel reacts by setting

the appropriate devices into action. It may cause a siren to sound,

transmit a coded signal to the central station, cause keypad lights

to blink, etc. TheXL1218 Digital Keypad will tell you the statusof your

security system at all times.

The following pages will familiarize you with the simple operation of

the system, via the Digital Keypad, and will explain the meanings of

the lights and buzzer.

TABLEOF CONTENTS

Operation page

arming the System .................................... 1

instant (“home”) feature .................................... 1

disarming the System ....................................... 1

zone bypass ................................................ 2

zone reactivation (“unbypass”) .............................. 2

keypad lights .............................................. 3

keypad buzzer ............................................. 4

panic (installer preset option) .............................. 4

Ambush (installer pre-set option) ............................ 4

Programming

fallback code .............................................. 5

users defined ............................................... 5

arm/disarm codes .......................................... 5

ambushcode .............................................. 6

erasing a code ............................................. 6

changing a code .......................................... 6

exit and entry delay ........................................ 6

ARM/DISARM OPERATION

To am your security system (with no zones bypassed):

I. Make sure that all of the Zone Status green lightsare Ifi If any of the

areen lights are off. the number will show you which zone has an

“open loop” (open window, etc.). You cannot arm the system with

an m-o. Once all protected openings are secured,:

2. Enter your 5digit secret code by gently depressing each number

key until you hear a momentary beep.

3. When all 5digits have been entered, the @“ARM” light will go on

and all of the greenzone lights will go 02. You now have a pre-sg

amount of time (exit delay time) to leave the premises through a

door designated by your installer as a delav zone.

Instant

(Home)

Feature

Disarming

I--

the

System

doors to report an Alarm instantly. This isaccomplished by selecting

the “INSTANT” option.

If you are stavinq within the premises, and no-one is expected to

return while the system is ARMED, you will want your time delay

To select the “Instant” option:

I. Arm the system

2. Press /

3. The zone 1 green light will go on

NOTE:This option automatically resets when the system isdisarmed.

To disarm your security system:

1. Enter your 5-digit secret code

2. The red “ARM” light will go 03

If you wish to arm only a part of your system,. such as the front doors

and windows, but still ham freedom come and go, for in-

stance, through the back door, you may bypass the desired zone(s)

and then arm the rest of the system. --

To bypass one or more zones:

1. Make sure that the system is disarmed (red light off),

2, Press 13 1(“Bypass”)

3. Press the number of the zone to be bypassed

Example: To bypass zone 3, Press

-- ~,tt-en~

4. The green zone light will blink slowly to indicate that that zone

is bypassed-- -

NOTE: To bypass additional zones repeat steps 2 and 3 above

5. Now arm the system by entering your 5-digit code. (All of the

greenlights will go off; the red light will go on)

-- - - -

NOTE: This option automatically resets when the system is disarmed.

Zone

Reactivation

(Unbypass)

Under normal conditions, bypassed zones are automatically

reactivated (unbypassed) when the system is disarmed. However,

AFTER A BURGLARY ALARM, .you must manually unbypass any

bypassed zones.

1 To mypaoa a single zone:

I, System must be disarmed

3. Press number of the zone to be unbypassed

4. The green zone light should stop blinking

To Unbypass all bypassed zones:

1. System must be disarmed

2. Press

(“Reset”)

KEYPADLIGHTS

Each green light corresponds to a particular zone number (1-4).

Each may be on steady, blinking or off at various times, indicattng

different conditions of the zone. Since your security system has been

customized to suit your specific needs, your installer will identify

any “24-hour” zones in your system. The chart below shows the

meaning of the green lights.

Burglary Zones

ZONE STATUS SYSTEMDISARMED SYSTEMARMED

Good

Light On Light Off

Trouble Light Off Fast Blink *

Bypassed Slow Blink Does Not Display

in Armed State

* To stop blink, disarm system, then press b (“Reset”)

ZONE STATUS

Good

Trouble

Bypassed

24-Hour Zones

ALARM ZONE TROUBLE ZONE

Light Off Light On

Light Off Light Off

Cannot Be Bypassed Slow Blink

Each amber light monitors a particular function of your security

system, and is labelled accordingly. If the function is operating

normally, the light is on.

“AC.” light off: the mxn electrical power supply is off.

“FIRE” light off: trouble in the fire circuit

“BAT(TERY)” light off: low battery (back-up power supply)

Light off: System Disarmed

Light on: System Armed

Slow blink: Central Station did not receive transmission* *

Fast blink: Alarm condition *

**TO stop blink, press E

(“Reset”)

* To stop blink, disarm system, then press’ io)

# (“Reset”) n

-w

THEKEYPADBUZZER

At the same time that any of the AMBER LIGHTS go off to indicate

a system problem, a trouble buzzer may sound. (Installer option)

- -

To silence the trouble buzzer:

1. Pressa (“Bypass”)

2. Press m ) (“Trouble Zone”)

NOTE: Remember to unbypass the trouble buzzer after the problem

has been corrected. Thisis accomplished by repeating steps I. and

2. above.

A MOMENTARY BEEPoccurs whenever a key isdepressed, indicating

that the system has received the number you have entered

Approximately 7 to 10 CONTINUOUS BEEPSis verification that your

system has successfully reached the central monitoring station with

a signal.

STEADYBUZZING is a reminder to DISARM your system after entering

the premises through one of the predetermined exit and entry zones.

OPTIONAL DIGITAL KEYPAD FUNCTIONS:

Ifyour system has been designed to incorporate the”panic”option,

RwGniignal to the central station and may or may not sound

an alarm at your premises (depending on theoptionyou selected).

To send a panic signal:

1. Press c and

simultaneously for approximately % second

El Cl

NOTE: If silent panic was selected, you will not receive the vm

cation buzzer.

AMBUSH

2. To reset audible panic, press

for about % second.

(installer lfyour system has been designed to incorporate the “ambush”

pre-set option,youll program a special AMBUSH CODE for “User 0” (see

option) programming Ambush Code, p. 6 .)

- To send an ambush signal:

1. Enter your User 0 &Digit Ambush Code

Example O-6-4-3-7

g 2. Enter any other user number (l-3) plus User O’s4-Digit Ambush Code

Example: 2-6-4-3-7

NOTE: If Ambush is not used, your user 0 code will function like all

other user arm/disarm codes]. 4

KEYPADPROGRAMMING

Your system is preprogrammed with a “FALLBACK” ARM/DISARM

CODE. Be sure to record this code. In the event of a total loss of

power (AC and battery), all codes with be erased. Your “Fallback”

code will enable you to arm and disarm the system and re-program

your personal secret code.

As many as four separate arm/disarm codes can be programmed.

Each code must begin with a different digit, which we call the ‘User

Number’: for example, “User l’s arm/disarm code would be 1 and

any four additional numbers: “User 2’s” code would be 2 and any

four additional numbers, etc. It is not necessary to program all

four codes.

USER

CODE

A user code may be programmed for temporary use for a service

person, guest, etc. and then erased (see below) when no longer

needed. This maintains the secrecy of your regularly used codes,

THE SYSTEM MUST BE IN A DISARMED MODE TO ACCOMPLISH ANc 7

PROGRAMMING. ALL PROGRAMMING ISDONE

USINGUSERI’SCODi-

(functions as an authorization code) THE NUMBER 9 MAY m

USEDIN ANY CODE.

To Program User l’s Arm/Disarm Code

1I Press ,

(Code Key)

2. Press number. 1

Dl , then the 4-Digit FALLBACK CODE

3. Press B again (The Zone 1 Green Light will blink slowly)

Now Press Any 4 Numbers Desired For User l’s Code. Do not use

AC9

(Upon completion of the 4th digit the zone 1 UghJ will stag blinking.

4. Test the new code by attempting to arm the system

NOTE: Remember to DISARM the system before attempting to pro-

gram any additional codes.

2. Enter your (New) User 1 (Authorization) Code

(The Zone 1_Green Light Will blink slowly)

a Now press the 4 Numbers Desired for User 2’s Code. Do not

(Upon completion of the 4th digit the Zone 1 fighJ will s&g bli

Repeat for User 3 and 0

User O’s Code may be programmed exactly as all other user codes

only if the keypad “AMBUSH” feature is not used. Thisfeature ispreset

by your installing company, if desired. (&explanation of “AMBUSH”

below.)

Ambush isa 4-digit code that will either turn the system ON if it isoff,

or OFF if it ison. ATTHESAME TIME it will send a SILENTEMERGENCY SIG-

NAL to the central monitoring station. The Ambush Code is pro-

grammed as User 0, following standard USERCODE PROGRAMMING

as described on page &

User 1 can erase any user’s code except his own, as follows:

2. Enter User 1 Code

3. Press User Number of Code to be Erased (e.g., if User 2 Code isto be

erased depress only the number d to erase entire code.

4. Press

(Reset Key)

Repeat Steps 1,2. and 3 above, entering User Number of code to be

USERCODE 4. Enter new 4-digit code desired (do not use ~9)

The exit and entrance delay times have been previously set for your

convenience and security. These allow you to enter ozave the

premises through specified “Delay Openings” while the system is

armed. If you feel these delay times are unsatisfactory, call your

installing company.

ABOUT THEMANUFACTURER

Your new XL1218 Control Panel and Remote Digital Keypad

are manufactured by Fire Burglary Instruments, Inc., leading

manufacturers of quality, reliable security control equipment

since 1971. These products have been engineered using the

latest advances in electronic and computer technology; and

are thoroughly tested by computer, as well as quality control

experts, several times during the manufacturing process.

Fire Burglary Instruments warranties its products through vour

installing company. Product Reliability and Ease of Operation

are two of the major factors in the engineering design of all of

Fire Burglary Instruments products; so you can look forward to

many years of trouble-free service from your new security P

.-,

system.

If you have any questions about the operation of your system,

call your installer:

ADDITIONAL NOTES:

Altri manuali per XL1218R

Indice

Altri manuali FBI Tastiera

FBI

FBI XL-1 XL4600 Manuale utente

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo