Feider Machines FFBE7TS-UK Manuale utente
GB
1
ORIGINAL INSTRUCTIONS
ELECTRIC LOGSPLITTER
FFBE7TS-UK
READ THIS INSTRUCTIONS MANUAL BEFORE USING THE TOOL
FEIDER 32, rue Aristide Bergès - ZI 31270 Cugnaux – France Made in PRC 2019
GB
2
DESCRIPTION OF THE SYMBOLS
WARNING! Standard graphic symbols are used on all machines in order to
ensure complete safety of all parts of the log splitter. As these symbols are very
important, read the information below attentively.
Conforms to relevant safety standards
It is obligatory to read the machine’s use and maintenance manual in full before
using the machine.
Wear eye protection! The requirement of eye protection when using the product
Wear hearing protection!
Wear safety footwear! It is obligatory to wear safety footwear at all times to
provide protection against the risk of logs accidentally falling on feet.
Wear protective gloves! It is obligatory to at all time to wear gloves which protect
the hands against chips and splinters which may be produced during work.
GB
3
Remove plug from mains before maintenance or if cord is damaged.
Keep bystanders away from the working area.
The log splitter must be always operated by one person only. Other people should
keep a safe distance from the work area, especially when the log splitter is under
operations. Never use another people to help you with freeing jammed log.
Danger! Keep clear of moving parts. Keep hands out of the way of all moving
parts.
Do not remove jammed logs with your hands.
Be careful to been stumbled.
Be careful to slip.
No smoking in the working area
The log splitter must always be used by one operator only.
GB
4
Recycle unwanted materials instead of disposing of them as waste. All tools,
hoses and packaging should be sorted, taken to the local recycling center and
disposed of in an environmentally safe way.
Danger! Keep clear of moving parts!
To be operated by one person only!
The log splitter must be used horizontally, can’t be used vertically.
SAFETY WARNINGS
Keep these instructions for future reference
1. The log splitter must always be used by one operator only.
2. Nobody must be allowed to use the log splitter unless they have read the
instruction manual and have been instructed in the regulations to follow for
correct and safe use.
Operators must receive necessary training and instructions.
3. The machine must be used by adults only. Use of the log splitter by
apprentices of not less than 16 years of age must be supervised by an adult
authorized to use the machine.
4. Never wear loose, unbuttoned clothing which may become trapped in moving
parts.
5. Check that the logs to be split are free from nails or wire, which may fly up or
damage the machine, the ends of the logs must be cut square, branches must
be cut off flush with the trunk.
6. Never try to split logs larger than those indicated in the technical specifications.
This could be dangerous and may damage the machine.
7. Break wood in the direction of the grain, do not place wood across the log
splitter and leave it in that position for splitting; it may be dangerous and may
seriously damage the machine.
8. Never attempt to cut two logs at once, one may fly up and hit you.
GB
5
9. If the log moves away from the blade, retract the blade and turn the log
through 900.
10.Do not attempt to load the log in the log splitter while the blade is in motion,
you could get trapped and injured.
11.Keep your hands well away from any splits and cracks which open in the log;
these may close suddenly and crush or amputate your fingers.
12.Never force the log splitter for more than 5 seconds keeping the cylinder under
pressure in the attempt to split excessively hard wood. After this time interval,
the oil under pressure is overheated and the machine could be damaged. It is
thus better to stop and rotate the log by 900 to see whether it can be split in a
different position. In any case, if you are not able to split the log, this means
that its hardness exceeds the capacity of the machine and thus that log should
be discarded so as not to damage the lop splitter.
13.Do not force the blade by pushing the log on the upper part, as this can cause
the blade to break or damage the body of the machine. Always set the log on
the guides.
14.Never leave the machine unattended while it is running. If you leave the
machine, even for a short time, remove the power supply or any possible
cause of accidental start-up.
15.The log splitter must never be used by an operator who is under the influence
of alcohol, drugs, medicines, or who is tired. A clear mind is essential for
safety.
16.Never request the assistance of another person to help you remove a jammed
log.
17.Do not use machines with electric motor if natural gas, petrol fumes or other
inflammable vapors are present.
18.Check that the electric circuit is adequately protected and that it corresponds
with the power, voltage and frequency of the motor, check that there is a
ground connection, and a regulation differential switch upstream.
Check on the functioning of the machine.
19.Never open the switch box on the motor. Should this be necessary, contact a
qualified electrician.
20.Make sure that the machine and the cable never come in contact with water.
21.Treat the power cable with care, do not attempt to move the machine by
pulling the cable, do not yank the cable to unplug it; keep the cable away from
excessive heat, oil and sharp objects.
22.Never leave the machine unattended with the power supply “on”, also
disconnect the power cable when not in use, when carrying out maintenance
work, when changing attachment or moving the machine.
23.Before starting work, hydraulic pipes and hoses shall be inspected and the
stopping devices shall be tested.
24.Keep the working area free from obstructions, e.g. logs, split wood etc.
25.Stop the machine before cleaning or making adjustments.
26.The hazards may arise from particular characteristics of wood when being split
GB
6
(e.g. knots, logs of irregular shape etc.)
27.Operator must receive necessary training and instruction from a qualified
person before handling the tool.
28.Use the tool only for the intended use. Misuse (such using material other than
log) can damage the tool and cause accidents and injuries.
29.The splitting operation of the machine is designed to be activated by one
person. While there is the possibility that additional operators could be working
with the machine (e.g. for loading and unloading), only one operator should
activate splitting operations.
30.The machine shall not be used by children.
31.Wear suitable personal protective equipment (PPE), including safety footwear;
close fitting clothing and suitable work gloves, eye protection and hearing
protection.
32.Before starting work, hydraulic pipes and hoses shall be inspected and the
stopping devices shall be tested.
33.Tests of the machine's safety devices before use the tool. If safety devices do
not work properly, do no use the tool and bring it to a qualified technician for
inspection and reparation.
34.The working area shall be free from obstructions; before installation and
operation, clear the working area. Keep the working area free from
obstructions, e.g. logs, split wood, etc.
35.Do not leave the machine unattended when running;
36.Do not reach into the splitting zone;
TRANSPORTING THE WOODEN SPLITTER TO THE PLACE OF WORK
The log splitter is equipped with 2 wheels for minor displacements. To move the
log splitter to your workplace, roll log splitter at a slight angle after making sure the
oil tank cap is tight.
Do not lift or carry the log splitter to move it.
Electrical Safety
WARNING! Always check that the power supply corresponds to the voltage on the
rating plate.
WARNING! Connect the main leads to a standard 230V±10% (50Hz±1Hz)
electrical supply which has protection devices of under-voltage, over-voltage,
over-current as well as a residual current device (RCD) which maximum
residual current rated at 30mA.
Replacing cables or plugs
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
GB
7
Immediately throw away old cables or plugs when they have been replaced by new
ones. It is dangerous to insert the plug of a loose cable in the wall outlet.
Using extension cables
1. As a supply for this machine always use an unloaded line and/or extension with
conductor of at least 2.5mm2 and protected with a 20A fuse. Be sure that this
extension cable is no longer than 10 meters. Excessively long cables or
inadequate section can cause voltage drops that prevent motor from developing its
full power.
2. Only connect your machine and/or extension cable to earthed electricity mains.
Grounding
In the event of an electrical short circuit, grounding reduces the risk of electric shock.
Use switch socket with grounding please.
INTENDED USE
This log splitter is only intended to be used to split logs! Serious injury may occur if
this log splitter is used for any other purpose.
TECHNICAL SPECIFICATIONS
Model
FFBE7TS-UK
Voltage:
230V~ 50Hz
Power consumption
2300W S3 50% (5min on/5min off)
No load Speed:
2,800min-1
Classification
Class I
Protection degree
IP 54
Max. splitting force (tons)
7 t
Diameter
30-250mm
Length
520mm
Max. Hydraulic oil capacity
2.4L
Max. hydraulic pressure
28MPa
Mass
67Kg
Sound pressure level, LpA
78 dB(A) k=3dB(A)
Sound power level, LWA
91 dB(A) k=3dB(A)
Vibration
≤2,5m/ s2
Guarantee noise level
91dB(A)
UNPACKING
GB
8
WARNING! To prevent accidental starting that could cause possible serious
personal injury, assemble all parts to your log splitter before connecting it to power
supply. Log splitter should never be connected to power supply when you are
assembling parts, making adjustment.
Carefully remove all pieces from the carton. Place the log splitter on a flat, high
work surface so that the control actuators are at least 850 mm (maximum: 1650
mm) high from the ground.
Separate and check against the list of loose parts.
WARNING! If any parts are missing, do not operate this machine until the missing
parts are replaced. Failure to do so could result in serious personal injury.
•Do not discard the packing materials until you have carefully inspected the log
splitter, identified all parts, and satisfactorily operated your new log splitter.
Check all loose parts from the box with the list below. Assemble according to the
instruction on the following pages.
1 horizontal leg 1pcs
2 front stand 2pcs
3 back stand 2pcs
4 horizontal shaft 2pcs
5 wheel 2pcs
6 wheel shaft 2pcs
7 wheel cover 2pcs
8 circlip 8pcs
9 Bolt M8*45 4pcs
Bolt M8*50 6pcs
10 Nut M8 4pcs
11 Flat washer 12pcs
12 Spring washer 4pcs
FEATURES
1. Before attempting to use, familiarize yourself with all the operating
features and safety requirements of your log splitter.
GB
9
1. Blade
2. Oil tank
3. Hydraulic control lever
4. Rolling wheel
5. Push button switch
6. Log pusher
7. Safety guard for hydraulic control lever
8. Horizontal leg
9. Horizontal shaft
10. Front stand
11. Wheel shaft
12. Motor cover
13. Back stand
2. Size of the logs to be split
The figure 1 shows the maximum log sizes that can be split.
The diameter of the log is indicative: a small log can be difficult to split if it has
knots or a particularly tough fiber. On the other hand, if the wood has regular
fibers it is not difficult to split logs with diameter greater than the maximum shown
in fig. 1.
It is important not to insist when the log does not split on the first attempt,
as the pump may be damaged by the overheating of the oil when the
machine is made to work under the maximum stress in the attempt to split
excessively hard wood.
3. Recommended oils
We recommend use of the following oils for the hydraulic cylinder.
SHELL TELLUS T22
ARAL VITAM GF22
SP ENERGOL HCP22
Fig.1
GB
10
MOBILE DTE 11 OR equivalent
DO NOT USE OTHER GRADE OILS
4. Application conditions
This log splitter is a home use model. It is designed for operating under ambient
temperature between +50C and 400C and use at altitudes no more than 1000mm.
The surrounding humidity should less than 50% at 400C. It can be stored or
transported under ambient temperatures between -250C and 550C.
ASSEMBLY
Warning! For your own safety, do not connect the log splitter to the power
source until the machine is completely assembled and you read and
understand the entire instruction manual.
Warning! For your own safety, never forget to bolt the support legs to the
log splitter, place the log splitter on flat and level ground.
Warning! Never use the log splitter if it is not in perfect order or if it needs
servicing. Before starting work, check correct functioning of all the safety
devices (ZHB, push button).
a) Connect front stand (10a) to connection pipe (a) and front stand (10b) to
connection pipe (b) by bolts and nuts (fig.2).
fig.2
b) Connect horizontal shaft (9a) to front stand(10a&10b) with screws, then
assemble horizontal leg(8) and fix it to front stand(10a&10b) by bolts (fig.3).
Indice
Altri manuali Feider Machines Spaccalegna
Manuali Spaccalegna popolari di altre marche
Scheppach
Scheppach OX 3-1000 Istruzioni per il montaggio
Swisher
Swisher 21200 Manuale utente
Elem Garden Technic
Elem Garden Technic FBHT65-22TCH Manuale utente
Champion Power Equipment
Champion Power Equipment 90720 Manuale
Boss Industrial
Boss Industrial ES5T20 Manuale utente
Villager
Villager LSP 12 T Manuale utente
