Fein BLK1.3TE Guida all'installazione
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 2/38
Contents
1. Models described
2. Technical data
3. Provisions
4. Tools required
5. Lubricants and auxiliary substances required
6. Disassembly
7. Assembly
8. Connection diagram
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 3/38
1. Models described
These instructions describe how to repair the following models:
Model Order no.
BLK 1.3 TE 723241
BLK 1.3 CSE 723242
BLK 1.6E 723238
BLK 1.6LE 723239
BLK 2.0E 723240
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 4/38
2. Technical data
Technical data
The complete technical data can be found in the operating instructions for the model.
Test data
Up-to-date test data for all models can be found on the FEIN Extranet (Customer Service → Repair Guides).
Lubricants
Lubricants and container sizes available from FEIN can be found on the FEIN Extranet
(Customer Service → Repair Guides).
Lists of spare parts
Lists of spare parts and exploded views are available online at www.fein.com
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 5/38
3. Provisions
Provisions
Please note that power tools may only be repaired, maintained and checked by a trained
electrician, as improper repair can result in serious risks to the user.
The provisions set out in DIN VDE 0701-0702 should be observed after repairs.
Only use original FEIN spare parts!
The relevant accident prevention regulations of the employers’ liability insurance associations are
to be observed when commissioning.
The German Equipment and Product SafetyAct applies for correct use.
Outside Germany, the regulations applicable in the relevant country must be observed!
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 6/38
4. Tools required
Standard tools
Open-ended spanner: WAF 30
Plastic hammer
Screwdriver: Torx 15
Flat nose pliers
Long-nosed pliers
Circlip pliers
Punch
Arbor press
Cable hooks
Sleeves
Special tools
Drawing-off socket cap 6 41 04 150 00 8
Chuck cone 6 41 07 019 00 7
Chuck cone 6 41 07 026 00 0
Press-in fixture 6 41 22 108 00 0
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 7/38
5. Lubricants and auxiliary substances required
Lubricants
Grease 0 40 108 0400 8 15 g Gearbox, needle bearing, ball bearing
Grease 0 40 119 0500 7 Sliding surfaces of plunger, con rod, punch
Auxiliary substances
Loctite 574 Between gearbox head and intermediate bearing
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 8/38
4. Disassembly
Before starting to remove the
motor or gearbox, the tool must always be disconnected from
the mains.
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 9/38
4.1. Disassembly - Motor
1.Remove screws and lift off cover.
2.Unscrew carbon holder.
3.Unscrew traction relief.
4.Unscrew plug connection between motor and electronics.
Tool:
- Screwdriver
Torx 15
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 10/38
4.2. Disassembly - Separating motor and gearbox
1.Remove screws.
2.Remove gearbox housing with armature from motor housing.
3.Remove sealing ring from intermediate bearing.
4.Remove intermediate gear shaft from intermediate bearing or gearbox housing.
5.Remove air guide ring.
Tool:
- Screwdriver
Torx 15
- Plastic hammer
Altri manuali per BLK1.3TE
3
Questo manuale è adatto per i seguenti modelli
9
Indice
Altri manuali Fein Utensili elettrici
Fein
Fein AFSC 1.7Q Guida all'installazione
Fein
Fein AFMM14 Manuale utente
Fein
Fein MM 300 Plus Manuale utente
Fein
Fein BLK1.3TE Manuale utente
Fein
Fein AFMT12 Manuale utente
Fein
Fein 7 272 Manuale utente
Fein
Fein MultiMaster AFMM18QSL Manuale utente
Fein
Fein KBM80U Manuale utente
Fein
Fein MM 300 Plus Manuale utente
Fein
Fein KFH17-8R Guida all'installazione
Fein
Fein GWP10 Manuale utente
Fein
Fein KBM 65 U Guida all'installazione
Fein
Fein MOtlx 6-25 Manuale utente
Fein
Fein AKFH18-5 Series Manuale utente
Fein
Fein BSS 2.0 E Guida all'installazione
Fein
Fein ASCT 14 Guida all'installazione
Fein
Fein FMM350QSL Manuale utente
Fein
Fein BSS 1.6 E Guida all'installazione
Fein
Fein ASCM12 Manuale utente
Fein
Fein MOtlx 6-25 Manuale utente
