Fenger FDM-4000i Foglio di istruzioni

FDM-4000i Manual V1.0

INSTALLATION & CONFIGURATION MANUAL

FDM-4000i

4-port SD Digital Modulator with IP

- 2 - FDM-4000i Manual V1.0

TABLE OF CONTENTS

SAFETY PRECAUTIONS .....................................................................................................................3

PACKAGE CONTENTS ........................................................................................................................4

PRODUCT DESCRIPTION ...................................................................................................................4

SPECIFICATIONS .................................................................................................................................5

INSTALLATION ....................................................................................................................................6

UNPACKING and INSPECTION......................................................................................................6

PRODUCT PICTURES and DIAGRAMS.........................................................................................6

HARDWARE INSTALLATION and CONNECTIONS....................................................................7

DEVICE Programming and Setup ..........................................................................................................8

Connecting to the GUI Interface:............................................................................................................8

Encoder Programming and Setup via GUI Interface: .............................................................................9

Overview Page of Fenger Encoder.....................................................................................................9

Common Setup.................................................................................................................................10

RF Setup...........................................................................................................................................11

Encoder Setup...................................................................................................................................12

IP Streaming Setup...........................................................................................................................13

Network Configuration.....................................................................................................................14

Administration..................................................................................................................................15

Front Panel LCD Encoder Menu Map ..................................................................................................17

Modulator Configuration via Front Panel LCD....................................................................................18

Common Setup Menu.......................................................................................................................19

RF Setup Menu ................................................................................................................................19

Encoder Setup Menu .......................................................................................................................20

Web Management Network Setup....................................................................................................23

DIGITAL MODULATOR NOTES.......................................................................................................24

- 3 - FDM-4000i Manual V1.0

SAFETY PRECAUTIONS

The presence of this symbol is to alert the installer and user to the

presence of uninsulated dangerous voltages within the product’s

enclosure that may be of sufficient magnitude to produce a risk of

electric shock.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

DEVICE TO RAIN OR MOISTURE. DO NOT OPEN THE UNIT. REFER SERVICING

TO QUALIFIED PERSONNEL ONLY.

DO NOT apply power to the unit until all connections have been made, all components

have been installed and all wiring has been properly terminated.

DO NOT terminate, change or uninstall any wiring without first disconnecting the unit’s

power adapter from the device.

DO NOT connect the power supply to the device if the power cord is damaged.

DO NOT cut the power cord.

DO NOT plug the power cord into an AC outlet until all cables and connections to the

device have been properly connected.

The device should be installed in an environment consistent with its operating temperature

specifications. Placement next to heating devices and ducts is to be avoided as doing so

may cause damage. The device should not be placed in areas of high humidity.

DO NOT cover any of the device’s ventilation openings.

DO NOT cover or obstruct the device’s fan or fan openings.

If the device has been in a cold environment allow it to warm to room temperature for at

least 2 hours before connecting to an AC outlet.

- 4 - FDM-4000i Manual V1.0

PACKAGE CONTENTS

This package contains:

One FDM-4000i SD IP Digital Modulator

One Power Cord

One Installation Manual

Inspect the package before starting installation to ensure there is no damage and all supplied

contents are present. Contact your distributor or dealer should the device be damaged or

package contents are incomplete.

PRODUCT DESCRIPTION

FENGER’s FDM-4000i encoder/modulator converts Digital Video Broadcasting (DVB)

standard definition video and audio signals to DVB-T. The unit features programmable channel

and network names. Adjustable RF output (Normal, Inverted, and C.W.), adjustable logic

channel numbering (LCN) and adjustable attenuation are standard features. The unit’s front-

mounted LCD display and controls allow for easy configuration and adjustments.

The FDM-4000i SD IP Digital Modulator is perfect for multi-video distribution solutions in the

commercial and institutional market (hotels, motels, sports bars, boats, restaurants, hospitals,

casinos, business and university campus, etc.).

- 5 - FDM-4000i Manual V1.0

SPECIFICATIONS

FDM-4000i

4-input SD Encoder Modulator with IP

Input

Video Input

CVBS

Video Input Level

0.7 - 1.4V (peak-to-peak)

Video Mode

PAL / NTSC

Audio Input

Stereo

Audio Input Level

0.4 - 4.8V (peak-to-peak)

Video & Audio Connectors

RCA female

Impedance

75 Ohm

RF Output

Standard

DVB-T according to EN 300 744

Frequency Range

E2 (50.5MHz) ~ S20 (296.5MHz) with 7 MHz interval

S21 (306MHz) ~ E69 (858MHz) with 8 MHz interval

Channel Bandwidth

7 MHz, 8 MHz

MER

36dB typical

Output Level

105dBμV typical

Output Level Adjustment

0 to -20dB (1dB step)

Output Impedance

75 Ohm

Output Connector

"F" female

IP Output

Streaming Method

RTP/UDP Unicast, RTP/UDP Multicast

Output Connector

RJ-45, 1Gbps

Modulation

Video Resolution

PAL 720x576@25ftp / NTSC 720x480@30ftp

Video Compression

MPEG-2, MP@HL 4:2:0

Audio Compression

MPEG-1 Layer II

LCN Processing

Yes

Carrier (OFDM Mode)

2K, 8K

Guard Intervals

1/32

Code Rate (FEC)

7/8

Constellations

64 QAM

Programming Interface

Local Setup

LCD Display + keypad

Remote Management

via Web Browser from any PC

Language

English

General

Power Supply

100 to 240 VAC, 50/60 Hz

Power Consumption

2.050 mA

Temperature Rating

0 ºC to +45 ºC

Dimensions

482.7mm x 240mm x 44.4mm, 1RU

Weight

3.40 Kilograms

*Specifications are subject to change without prior notice

- 6 - FDM-4000i Manual V1.0

INSTALLATION

System Installer must adhere to Article 820-40 of the NEC that provides

guidelines for proper grounding and specifies that the cable ground shall

be connected to the grounding system of the building, as close to the

point of cable entry as possible.

UNPACKING and INSPECTION

Each unit is shipped factory tested. Ensure all items are removed from the container prior to

discarding any packing material.

Thoroughly inspect the unit for shipping damage with particular attention to connectors and

controls. If there is any sign of damage to the unit or damaged or loose connectors contact

your distributor immediately. Do not put the equipment into service if there is any indication of

defect or damage.

PRODUCT PICTURES and DIAGRAMS

- 7 - FDM-4000i Manual V1.0

HARDWARE INSTALLATION and CONNECTIONS

1. The unit is designed to be rack mounted in a standard EIA 19” rack.

2. Use a 75Ω coaxial cable with RCA connectors to connect the video source (e.g., STB,

DVD, VCR, and Camera) to the unit’s yellow RCA VIDEO INPUT jack (IN1…IN4).

Repeat this step for each video source connection.

It is highly recommended that quality coaxial cable and connectors be used for all

video source connections.

3. Use RCA cables to connect the audio source to the red / white AUDIO L and AUDIO R

INPUT jacks (IN1…IN4). Use the red and white jacks for audio input or either one for a

single input.

Repeat this step for each audio source connection.

Be sure the video and audio connections for each source are consistent with the unit’s

inputs (IN1…IN4).

It is highly recommended that quality cables and connectors be used for all audio

source connections.

4. Use a quality 75Ω coaxial cable with “F” connectors from the unit’s RF OUT jack to the

distribution system (combiner or reverse splitter).

5. Connect the included power cord to the unit’s POWER plug.

6. Connect the power cord to an appropriately rated AC power outlet.

- 8 - FDM-4000i Manual V1.0

DEVICE Programming and Setup

To setup and program the Encoder you can use the GUI interface or the LCD Front Panel

Connecting to the GUI Interface:

Connect an Ethernet cable directly (no Cross Over cable required) to the Web Management

Port on the rear panel of the Encoder or connect the Ethernet cable to an Ethernet switch.

Connect an Ethernet Cable to your PC.

Static IP address

A static IP address must be used on the computer you use to configure the Encoder.

Refer to the computer’s operating software documentation for assistance on using static

IP addresses.

Starting GUI Interface

Open a web browser window

Enter “http://192.168.1.9”in the web address field

Note: To setup the encoder using the Front Panel LCD see “Modulator Configuration via Front

Panel LCD”.

- 9 - FDM-4000i Manual V1.0

Encoder Programming and Setup via GUI Interface:

Step 1:After setting the static IP address in the web address field, press Enter and you will

view the Device Webpage.

Overview Page of Fenger Encoder

Welcome page showing overview status of the Encoder when fully functioning.

Step 2: Login Select Common Setup

Once the Common Setup Tab is selected you will be prompted to enter the user name and

password for device.

Default User Name: admin

Default Password: Admin123

Note: To change the Password for the GUI go to the Administration Tab

- 10 - FDM-4000i Manual V1.0

Step 3: Common Setup Tab

Common Setup

Use the Common Setup Page to set the Output channel, Attenuation, LCN Mode, and Device Address.

Step 4: Local Save

Once all parameters are set you are required to do a Local Save.

Notes on Changes:

Changes made to an individual setup tab may require the installer to perform a Local Save

AND Upload and Reboot to the device if only making changes to one parameter of the

encoder.

Example: Installer is required to change only the output channel for the device (No other

changes to the device are required). Once the channel has been changed, the installer is

required to perform 1: Local Save AND 2: Upload and Reboot.

Indice

Manuali Modulatore popolari di altre marche

axing

axing AVM 5-00 Manuale utente

IKUSI

IKUSI MAC-HOME HD Manuale utente

Wisi

Wisi MINI OM 10 Manuale utente

RCA

RCA CRF910 Manuale utente

Pico Macom

Pico Macom PM45 Manuale utente

FTE Maximal

FTE Maximal MODIG AIR Manuale utente

Thor Broadcast

Thor Broadcast H-IP-32RF Manuale utente

Delphi

Delphi SA10003 Manuale utente

Elan

Elan MOD3000 Manuale utente

ClearView

ClearView SD4260 Manuale utente

Televes

Televes T.0X COFDM-QAM CI Manuale utente

Crucial Audio

Crucial Audio Die Gotterdämmerung Manuale utente

Pioneer

Pioneer CD-V61FM Manuale utente

Televes

Televes 554912 Manuale utente

Newtec

Newtec M6100 Manuale utente

ProTelevision

ProTelevision PT 5780 Manuale utente

Argent Cables

Argent Cables HD DVB-T MODULATOR Manuale utente

SSS Siedle

SSS Siedle BVM 650-0 Manuale utente