Fenton 351.1833 Manuale utente
351.1833 CCTV Security 4 Cam Wireless
NVR kit. User Manual
User Manual
Handleiding
Betriebsanleitung
V2.0
1. Statement
Thanks for purchasing our products, please contact us for any question or requirement.
This manual is meant only for FENTON wireless network video recorder kit.
2. Safety Cautions
1. Please do not put any container with liquid on the device(like vase with water).
2. Please put the device at a ventilated place and prevent clogging the ventilation hole.
3. Please check the power voltage, to avoid any damage to device caused by wrong voltage.
4. The NVR should work under the technical standard temperature and humidity.
5. Please place the device horizontally and keep it away from sharp pounding environment.
6. Moisture and dust on the unit may cause short circuit, for long-term use, please remove the dust on the
unit, connector by brush periodically.
7. Battery replacement by yourself is not suggested, since incorrectly operation may cause burst. Please
contact professional person for battery replacement.
8. Please install the device according to safety norms, you could take the national or local standard as
reference.
3. Package Inspection
Please check the device and all accessories according to packing list. Please contact the distributor timely
in case of any damage or lack of accessory.
1. Product Features & Specification
1.1 Wireless NVR Features
2.4GHz transmission technology 4CH 720P wireless NVR.
Embedded Linux operation system.
Standard H.264 video compression.
Main Chip: Professional industrial processor Hi3520.
4CH 720P real-time recording & synchronous playback.
Auto code matching realizes convenient real P2P application.
More stable wireless signal, Max. 35M transmission distance.
SSID technology guarantees the safety of use.
Motion detection, privacy masking, email alert.
Multiple simultaneous viewing by web browser or smart phone.
Support HDMI/ VGA video output.
Support HDD, USB flash driver storage & backup.
Reserved 3 Ethernet ports for wired IP camera connection.
1 * Standard RJ45 Port, 2*USB 2.0 Port
Network Protocol: UPnP, SMTP, PPPoE, DHCP, FTP, ETC.
1* SATA, Max. 4TB HDD.
Power: DC 12V 2A.
Wireless NVR Technical Parameters
Operating System
Embedded Linux OS
Main Chip
Hi3520
Video Input
4 channel bandwidth 20Mbps
Video Output HDMI
1024*768, 1336*768, 1440*900, 1920*1080
Video Output VGA
1024*768, 1336*768, 1440*900, 1920*1080
Video Playback
4channel synchronous playback 720P / 960H / D1 optional
Recording Mode
Auto / Manual / Motion Detection / Alarm
Playback Mode
Multiple slow / fast playback, real time, routine, event
Backup Mode
Support HDD, USB flash driver, E-cloud storage & backup
HDD Type
1*SATA, Max.4TB
External Interface
4*LAN port (1* adaptable RJ45 10M/100M WAN port
3*reserved LAN port for wired IP camera)
Network Protocol
Upnp(play & plug), SMTP(email service), PPPoE(dial-up),
DHCP(automatically obtain an IP address), etc.
Power Supply
DC 12V/2A
Power Consumption
<= 5W
Working Environment
Temperature -10°--50°, Humidity 10%--90%
Size
257(L) * 210(W) * 45 (H)mm
Weight
1 KG
1.2 Wireless IP Camera Features
2.4GHz wireless transmission technology.
Standard H.264 video compression.
Enhanced wireless module, more stable signal.
Up to 25M transmission distance.
1.0 Megapixels/ 720P wireless IP camera.
Sensor: 1/4” Progressive Scan CMOS Sensor.
Main Chip: Professional industrial processor.
Solution: OV9712+Hi3518E.
Fixed 3.6mm/ 6mm lens optional.
Main stream 1280x720@30fps.
Min. illumination 0.01Lux (0Lux IR Led on).
Smart IR-cut, auto switch day& night vision.
F5* 36pcs IR Leds, 25M effective visual range.
Auto white balance, high sensitivity.
Power: DC12V 1A.
Wireless IP Camera Technical Parameters
Operating System
Embedded Linux OS
Main Chip
Professional industrial processor
Image Sensor
1/4’’ Progressive scan sensor
Solution
OV9712+Hi3518E
Image Resolution
1.0 megapixel, 1280x720P
S/N Ratio
>48dB
Minimum Illumination
Color: 0.1 Lux, B/W: 0.01 Lux
Lens
Fixed 3.6mm
IR Leds
36pcs Leds
Effective Range
Night vision 25M
OSD
Optional (Date Time & Title)
White Balance
Auto
Day & Night
Auto / Color / B&W
3D-DNR
Auto
Mirror / Flip
On / Off
Privacy Masking
4 zones selectable
Frame Specification
Dual Stream: H.264 128x720@30fps or lower
Sub Stream: H.264 640x480@30fps or lower
Anti-thunder Level
Standard IEC6100-4-5
Interface
RJ45/WIFI 802.11b/g/n
Working Environment
Temperature -10°--50°, Humidity 10%--90%
Size
180(L) * 62(W) mm
Weight
500Gr
2. Hardware Operation
2.1 Front Panel
1．PWR：Power indicator light
2．HDD：Hard disk indicator light
2.2 Rear Panel
2.3 Connection Diagram
2.4 Antenna Direction
2.5 Hard Drive Installation
Please note the NVR recorder was pre-installed 1TB HDD inside.
1.Hard drive storage capacity measurement conversion
B
1 B = 8 b
MB
1 MB = 1000 KB
GB
1 GB = 1000 MB
TB
1 TB = 1000 GB
2. How to calculate recording consumption of HDD capacity
--1. One channel recording file size in one hour: A= B / 8 / 1000 *3600
--2. “N” channels recording file size in 24 hours: A= B / 8 / 1000 *3600 *24 *N
--3. “N” channels recording file size in D days: A= B / 8 / 1000 *3600 *24 *D *N
A: Required memory ; B: Code rate ; N: Channels ; D: Recording days
2.6 Packing List
3. System Software Operation
3.1 Turn on/off
1. Make sure the access AC voltage is stable during NVR configuration and use.
2. Connect NVR to monitor by HDMI / VGA video output cable.
3. Apply power to boot up the device, the [power] indicator will be on. When entering the system, it’s a
normal status if the status indicator flashes. The system booting as shown below.
No.
Items
Quantity
1
Wireless NVR
1 pcs
2
Wireless IP camera
4 pcs
3
USB mouse
1 pcs
4
1TB HDD (pre-installed)
1 pcs
5
1M network cable (for IP camera code
1 pcs
6
DC 12V/2A power adapter (for NVR)
1 pcs
7
DC 12V/1A power adapter (for IP
4 pcs
8
FENTON User Manual
1 pcs
9
CD disk
1 pcs
10
Screw bag
4 pcs
3.2 Login
After system is turned on and initialized，it will pop up the login interface automatically as shown below.
Login steps:
1. Left click and enter user name to login. (default users name is “admin” by factory setting)
2. Left click and enter the logging password.(default password is blank by factory setting)
3.Click the “OK” to complete login.
Note: Password can be numbers, operators or */ #, for no longer than 10 characters.
3.3 Logout
Right click mouse to get main menu, go to Exit system (System logout)→ Logout/ Reboot/ System
shutdown.
If users need to logout automatically, steps are below:
Right click mouse to get main menu→ System setup→ General setting→ enable logout automatically→
device logged off without operation in 1 minute→ Re-enter user name & password to login.
3.4 Rebooting
Right click mouse go to main menu, select “ System logout”, click the “rebooting”
4. Setup Wizard
After Logging in, the system will automatically open ” Setup wizard” to help user to complete basic settings.
4.1 Setup wizard
Scan QR-code to download the APP by mobile phone viewing. Check “Enable boot wizard”. (If users do not
click “Enable boot wizard”, all setup wizards steps below will not be prompted at next restarting)
4.2 General setup
Change the time zone/ date / time / language etc, click next to go to HDD setup as below.
4.3 HDD setup
Users can check Hard drive’s model number, capacity, status,etc as below. Also users can format HDD.
And click next to go to record setup.
4.4 Record Setup
Users can choose different record mode. Preset record plan based on channels, weekdays, and schedule,
user can set 4 schedule in the weekday selected for each channel. Or only recording by time / motion /
sensor as shown below.
4.5 Network setup
Users can choose auto DHCP, or edit IP address / gateway / subnet mask / PPPoE etc. click “Done” to
complete all setting as shown below.
Indice
Altri manuali Fenton Telecamera di sicurezza
