Festool LR 32-SYS Manuale utente

Festool LR 32-SYS tutorial

Brice Burrell

The LR32 will fit the OF1010 and the OF1400. Next, some have said that the Festool 35mm bit will not

cut into wood, stating the router spins the bit too fast and only burns the wood. I have had success

with this bit. I use the router on speed setting #1, the slowest setting. I have tried poplar, cherry, pine,

oak and birch ply with no problems. Below are the two kits Festool offers:

~ Part # 58329, Festool LR 32-SYS Hole Boring System For OF 1010 & 1400: Includes: Guide Plate,

Centering mandrel, 2 side stops, 2 end stops, 2 clamps, 35mm carbide-tipped hinge-location bit, two

5mm carbide-tipped dowel drills in #1 Systainer. Router and rail(s) not included.

~ Part # 583290, Hole Drilling System for OF 1010/1400 Routers: Guide plate with centering mandrel

and two side stops, two end stops. Router, drill bits, rail(s) and clamps not included.

Here are some pictures of the parts to the LR32 system.

End Stops

Side Stops

Guide Plate

OK now that we know what the parts look like, we can get started with this tutorial!

I will be making a shop cabinet (frameless, full over lay) from scrap/rejected plywood from other

projects, when done I hope to have a 36"x36"x12" cabinet for storing my abrasives. To get going I'll

need to size the plywood. The TS55 will make short work of this. The first time you use your LR32,

there are some one time adjustment that need to made to side stops. They are covered in the manual

so I won't get into that here. Now I'l attach the guide plate, shown here are both the OF1010 and

OF1400.

The OF 1010 is mounted with the centering mandrel, the clamps and thumb screws. First install the

8mm collet, then the centering mandrel, finger tight will do.

Place the router on the guide plate, plunge the mandrel into the hole in the guide plate and secure

with clamps and thumb screws. Remove the mandrel and replace router bit.

Here is a picture with the guide mounted to the OF1010.

The OF 1400 mounts to the guide with two screws, that’s it, see picture below.

All right, now I'll fit the end stops to the guide rail. But first a word about the end stops. The end stops

can be set to have either a 16mm or 32mm offset from the edge of the work piece to center of first hole

in the rail (remember this). The end stop has a thumb screw that goes through the holes in the rail into

the stop. I will drill the shelf pins in the cabinet first, so I will set the end stops to the 16mm offset.

You are looking at the bottom of the guide rail. Note, end stop to the first hole is 16mm, and you can

see the "16" on the end stop.

At this point I will mark where I want to drill the holes in all the work pieces. I use a small line, see

picture. Note "TOP" on the work, this is the top of the side piece of the cabinet.

Side stops go on now, mount the side stops to the rail to set the distance from edge to your first row

of holes. I will line up the rail/end stop to the "Top" of the cabinet (on the left in the picture below).

Clamp the rail and the work piece down to the MFT, now remove the side stops, they will get in the

way of drilling the holes. Here it is from below, very important, make sure you put the end stop up

against the end of the work piece.

A pin on the bottom of the guide plate locks into the holes on the rail.

On the guide plate, the lever is spring loaded and can be lifted to slide the guide plate down to the

next hole in the rail. Red arrow shows the movement of the lever, see picture below.

Place the router with 5mm bit on the rail and set the depth for the bit. Set the guide in line with the

hole you want your first shelf pin. Insert in the picture shows the bit lining up with the line for first hole

to be drilled.

Fire up the router and start to drill, lift lever and slide over to the next hole, drill, repeat until all holes

are drilled.

Remove the router and rail. I have now drilled the holes for the back row of self pin holes. I now

need to drill the front row of holes, so I will turn the work piece so the "TOP" will be on the right side.

Here it is, "TOP" on the right.

Now, place rail and side stops back on with the right end stop indexed on the "TOP,” this is very

important to get your holes to line up! Again, clamp and remove side stops and drill the hole, just the

like other side. I'll drill this set of holes now.

Here are the drilled, note the holes for mounting the hinge base plate.

Altri manuali Festool Utensili elettrici

Festool

Festool OSC 18 Manuale utente

Festool

Festool Domino DF 500 Manuale utente

Festool

Festool BHC 18 Istruzioni per l'installazione

Festool

Festool CONTURO Manuale utente

Festool

Festool OF 1010 Q Istruzioni per l'installazione

Festool

Festool Domino XL DF 700 EQ Istruzioni per l'installazione

Festool

Festool LRS 400 Manuale utente

Festool

Festool OF 1400 EQ Manuale utente

Festool

Festool PF 1200 E Alucobond Istruzioni per l'installazione

Festool

Festool Carvex PSC 400 EB Istruzioni per l'installazione

Festool

Festool Domino DF 500 Q Istruzioni per l'installazione

Festool

Festool OF 2000 E Manuale utente

Festool

Festool VS-600 Manuale utente

Festool

Festool PSC 420 EB Manuale utente

Festool

Festool TDK 12 Manuale utente

Festool

Festool OF 2200 EB Manuale utente

Festool

Festool RG 150 E Istruzioni per l'installazione

Festool

Festool CARVEX PSBC 420 Istruzioni per l'installazione

Festool

Festool OF 1010 EQ Manuale utente

Festool

Festool OF 1400 EQ Manuale utente

Festool

Festool MFK 700 EQ Manuale utente

Festool

Festool Quadrive DRC 18/4 Istruzioni per l'installazione

Festool

Festool Carvex PSC 400 EB Manuale utente

Festool

Festool Trion PS-300Q Istruzioni per l'installazione

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale