Festool ROTEX RO 150 Manuale utente

1/4

Description

Whether it is coarse sanding or fine sanding, overhead work or work in

upright areas, the ROTEX can be used everywhere - even in places that

are difficult to access.

The tool is also used for polishing in body workshops and by carpenters.

Areas of application RO 125 RO 150

Removal capacity + ++

Ergonomics ++ ++

Surface quality ++ ++

Processing large areas + ++

Upright work and overhead work ++ +

601/01

No. 601

Operation and function of

the ROTEX

601/02

601/03

601/04

2/4

Tools/Accessories

The following tools and accessories are used in this application example:

601/06

Designation Order No.

Geared eccentric sander ROTEX, RO 125 FEQ Plus 571533

Geared eccentric sander ROTEX, RO 150 FEQ Plus 571570

601/05

3/4

601/08

Preparation/Set-up

The economical 3-in-1 principle: one machine - three applications

Coarse sanding (also called rotary sanding)•

With this motion the pad is driven using a gear - forced rotation.

With the combination of eccentric and rotary motions the ROTEX

achieves up to three times higher material removal capacity than

other eccentric sanders.

Fine sanding (also called eccentric sanding)•

In this motion the pad rotates itself. You obtain a first-class, extra-fine

sanding pattern with this classic eccentric motion. If the machine

is pressed to hard on the workpiece, the pad sticks - this should be

avoided!. (This will have a negative impact on the sanding result).

Polishing (with the ROTEX rotary motion)•

For this application a rotation is needed so the gear is switched on.

The overlapping rotary and eccentric motions of the ROTEX ensure

optimal results also for polishing.

601/07

601/09

Procedure

To switch the machine from coarse sanding to fine sanding or vice-versa the

motor must be switched off.

The switching is effected via the slide switch located in the centre of the cap.•

If the switch is moved to the right (rough tab), the machine is in coarse•

sanding/rotary mode.

If the switch is moved to the left (fine tab), the machine is in fine sanding/•

eccentric sanding mode.

601/10

4/4

Our example for use is a recommendation tried and tested in practice. However the

actual conditions pertaining in each situation are completely outside of our control.

We therefore do not provide any form of guarantee. Any legal claims arising out of

this are not to be made against Festool. Please observe without fail the safety and

operating instructions included with the product.

www.festool.com

Pad change for the RO 125 FEQ

Disconnect the tool from the power supply.•

Remove the protector if this is mounted.•

Set the switch on the cap to coarse sanding (rotary mode).•

Press the lock button, which is located at the rear of the machine•

(this must be pulled out slightly for pressing).

Remove the sanding pad (anti-clockwise).•

Now put the other sanding pad in its retainer and secure it firmly•

into place (in clockwise direction).

601/1!

601/12

601/13

Positioning the protector

The protector prevents the sanding pad coming into contact with its•

other side (e.g. when sanding along a wall) and thus a kick-back of the

machine.

For assembly place the edge protection on the machine until you hear•

it lock in to place.

For removal pull out or press the protector on one end and then push•

it out from the guide.

Pad change for the RO 150 FEQ

Proceed as for RO 125.•

The lock button is located at the front of the machine at the side on the•

RO 150.

Also here the button must be pulled up slightly so that it can be pressed.•

Remove extraction channel (RO 150 FEQ)

As dust extraction is not required for polishing the extraction channel if

connected is removed as it may be an obstruction.

To do so the green button in the handle area must be pressed in the•

direction of the extractor connector. At the same time pull the extraction

channel to the back.

601/14

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Festool Levigatrice

Festool

Festool ES 150/3 EQ Manuale utente

Festool

Festool Rap 80.02 E Manuale utente

Festool

Festool RTS 400 Q Istruzioni per l'installazione

Festool

Festool SHINEX RAP 150 FE Istruzioni per l'installazione

Festool

Festool RTSC 400 Li Manuale utente

Festool

Festool ETS EC 150/3 EQ Istruzioni per l'installazione

Festool

Festool RAS 115.04 E Manuale utente

Festool

Festool RS 100 CQ Istruzioni per l'installazione

Festool

Festool ETSC 125 Li Manuale utente

Festool

Festool DELTEX DX 93 E Manuale utente

Festool

Festool ROTEX RO 90 DX FEQ Manuale utente

Festool

Festool ETS 125 REQ Manuale utente

Festool

Festool Rotex RO 150 FEQ Manuale utente

Festool

Festool RS 100 CQ Manuale utente

Festool

Festool DTSC 400Li Istruzioni per l'installazione

Festool

Festool LEX 150/3M Manuale utente

Festool

Festool ROTEX RO 150 FEQ Istruzioni per l'installazione

Festool

Festool RAS 115.04 E Manuale utente

Festool

Festool RS 100 Q Manuale utente

Festool

Festool RS 400 EQ Manuale utente

Festool

Festool LRS 400 Istruzioni per l'installazione

Festool

Festool SHINEX RAP 150 FE Manuale utente

Festool

Festool ROTEX RO 125 FEQ Istruzioni per l'installazione

Festool

Festool LEX 2 125/3 Manuale utente

Manuali Levigatrice popolari di altre marche

Oliver

Oliver 6305 Manuale utente

Jet

Jet 22-44 Pro-3 Manuale di servizio

Makita

Makita M9204 Manuale

Makita

Makita M9204 Manuale utente

Craftsman

Craftsman 351.215131 Manuale utente

Clarke

Clarke Woodworker CBS1-5B Manuale di istruzioni

Chicago Pneumatic

Chicago Pneumatic CP9778 Manuale utente

Nitto Kohki

Nitto Kohki BB-20 Manuale utente

Ferm

Ferm FEOS-135 Manuale utente

Unior

Unior 1510 Manuale utente

stayer

stayer ls1200 Manuale utente

Jet

Jet JSG-96 Manuale di servizio

Parkside

Parkside PDS 290 B2 Manuale utente

Status

Status XPA Series Manuale utente

Clarke

Clarke EZ Sand Manuale utente

Craftsman

Craftsman 113.22521 Manuale utente

Craftsman

Craftsman 113.225831 Manuale utente

CLAS

CLAS OP 1429 Manuale utente