FIBARO RGBW CONTROLLER 2 Manuale utente

FIBARO RGBW CONTROLLER 2

FGRGBW-442

OPERATING

MANUAL EN

v1.0

Table of contents

1: Important safety information 4

2: Description and features 5

2.1: Description 5

2.2: Main features 5

3: Specications 6

4: Installation 7

4.1: Before installation 7

4.2: Connection with RGBW/RGB LED strip 8

4.3: Connection with one-color LED strips 9

4.4: Connection with halogen lights 9

4.5: Connection with 0-10V analog sensors 10

5: Adding to Z-Wave network 11

5.1: Adding manually 11

5.2: Adding using Smart Start 11

6: Removing from Z-Wave network 12

7: Operating the device 13

7.1: Controlling the device using connected switches 13

7.2: Visual indications 13

7.3: Menu 14

7.4: Resetting to factory defaults 14

8: Z-Wave range test 15

9: Activating scenes 16

10: Regulations 17

Important safety InformatIon

1: Important safety information

Read this manual before attempting to install the device!

!Failure to observe recommendations included in this manual

may be dangerous or cause a violation of the law. The manu-

facturer, Fibar Group S.A. will not be held responsible for any loss or

damage resulting from not following the instructions of operating

manual.

Do not modify!

!Do not modify this device in any way not included in this

manual.

Other devices

!The manufacturer, Fibar Group S.A. will not be held responsi-

ble for any damage or loss of warranty privileges for other con-

nected devices if the connection is not compliant with their

manuals.

DANGER!

The device is powered with a secure voltage. Nevertheless, the

user should be careful or should commission the installation to

a qualied person.

DANGER!

To avoid risk of electrical shock, do not operate the device with

wet or moist hands.

This product is intended for indoor use only in dry locations.

!Do not use in damp or wet locations, near a bathtub, sink,

shower, swimming pool, or anywhere else where water or

moisture are present.

Not a toy!

!This product is not a toy. Keep away from children and

animals!

DescrIptIon anD features

2: Description and features

2.1: Description

FIBARO RGBW Controller 2 is an universal, Z-Wave Plus compatible

RGB/RGBW controller.

FIBARO RGBW Controller 2 uses PWM output signal, allowing it to

control LED, RGB, RGBW strips, halogen lights and other resistive

loads. It can also measure active power and energy consumed by the

load. Controlled devices may be powered by 12 or 24V DC.

Inputs support momentary/toggle switches and 0-10V analog sen-

sors, like temperature sensors, humidity sensors, light sensors etc.

2.2: Main features

• Compatible with any certied Z-Wave or Z-Wave Plus controller.

• Supports Z-Wave network Security Modes: S0 with AES-128 en-

cryption and S2 Authenticated with PRNG-based encryption.

• Works as a Z-Wave signal repeater.

• Allows for connecting:

»RGB/RGBW LED strip,

»one-color LED strips,

»halogen lights,

»0-10V analog sensors or potentiometers,

»other compliant resistive loads.

• Active power and energy metering.

specIfIcatIons

3: Specications

Power supply 12V/24V DC ±10%

Rated load current: 6A for channel,

12A total for all outputs

Power output: 144W combined for 12V

288W combined for 24V

Inputs 4, 0-10V (congurable

pull-up) or binary

Outputs 4, PWM

PWM frequency: 244Hz

Maximum length of wires: 2m

Operating temperature 0–40°C (32–104°F)

Radio protocol Z-Wave (500 series chip)

Radio frequency 868.4 or 869.8 MHz EU;

908.4, 908.42 or 916.0 MHz US;

921.4 or 919.8 MHz ANZ;

869.0 MHz RU;

Transmit power EIRP max. -1dBm

Range up to 50m (164 ft) outdoors

up to 40m (131 ft) indoors

(depending on terrain

and building structure)

Dimensions

(Length x Width x Height)

42.5 x 38.25 x 20.3 mm

(1.67” x 1.5” x 0.8”)

Compliance with EU directives RoHS 2011/65/EU

RED 2014/53/EU

Radio frequency of individual device must be same as

your Z-Wave controller. Check information on the box

or consult your dealer if you are not sure.

InstallatIon

4: Installation

4.1: Before installation

!Connecting the device in a manner inconsistent with this

manual may cause risk to health, life or material damage.

• Connect only in accordance with one of the diagrams,

• The device is powered with secure voltage; nevertheless, the user

should be extra careful or should commission the installation to a

qualied person,

• Do not connect devices which are not compliant with the

specication,

• Every connected device should be compliant with the relevant

safety standards,

• RGBW Controller 2 and the load connected to its output must

be powered by 12VDC or 24VDC stabilized power supply with

short circuit protection. Connecting higher voltage or voltage not

matching the load’s voltage may cause damage to the device,

• Connecting long RGBW/RGB/LED strips may cause voltage drops,

resulting in lower light brightness further from R/G/B/W outputs.

To eliminate this eect it is recommended to connect few shorter

strips in parallel connection instead of one long strip connected

serially,

• RGBW Controller 2 has 0-10V inputs. There is no 0-10V output.

Output is controlled by PWM at 244Hz,

• We recommend using monostable switches for comfortable light

control.

Notes for diagrams:

IN3

IN4

(R)

(G)

(B)

(

)

P(12/24V DC)

GND

IN1

IN2

FIBARO

RGBW Controller 2

OUT1

OUT2

OUT3

OUT4

P – 12/24V DC power supply connector

GND – ground connector

InstallatIon

IN1 – input connector for controlling OUT1 output

IN2 – input connector for controlling OUT2 output

IN3 – input connector for controlling OUT3 output

IN4 – input connector for controlling OUT4 output

OUT1 – output connector controlled by IN1 input (red LED color

recommended)

OUT2 – output connector controlled by IN2 input (green LED color

recommended)

OUT3 – output connector controlled by IN3 input (blue LED color

recommended)

OUT4 – output connector controlled by IN4 input (white LED color

recommended)

B – service button (used to add/remove the device)

4.2: Connection with RGBW/RGB LED strip

We recommend connecting LED strip channels in the same order as

on the diagram (R - OUT1, G - OUT2, B - OUT3, W - OUT4).

If you want to connect RGB strip, use the same diagram, but do not

connect OUT4 channel.

1. Disconnect the power.

2. Connect with the diagram below:

12/24V DC

GND

12/24V

IN3

IN4

OUT1

OUT2

OUT3

OUT4

IN1

GND

IN2

Diagram 1: Example connection with RGBW LED strip

(1 – power supply, 2 – switch, 3 – RGBW LED strip)

3. Verify correctness of connection.

4. Power the device.

5. Add the device to the Z-Wave network.

6. Change values of parameters:

• Connected to IN1:

»RGBW: change parameter 150 to 0

»HSV and White: change parameter 150 to 1

InstallatIon

4.3: Connection with one-color LED strips

1. Disconnect the power.

2. Connect with the diagram below:

12/24V DC

GND

IN3

IN4

OUT1

OUT2

OUT3

OUT4

IN1

GND

IN2

–

Diagram 3: Example connection with 4 one-color LED strips

(1 – power supply, 2 – switch, 4 – one-color LED strip)

3. Verify correctness of connection.

4. Power the device.

5. Add the device to the Z-Wave network.

4.4: Connection with halogen lights

1. Disconnect the power.

2. Connect with the diagram below:

12/24V DC

GND

IN3

IN4

OUT1

OUT2

OUT3

OUT4

IN1

GND

IN2

555

Diagram 4: Example connection with 4 halogen lights

(1 – power supply, 2 – switch, 3 – RGBW LED strip)

3. Verify correctness of connection.

4. Power the device.

5. Add the device to the Z-Wave network.

InstallatIon

4.5: Connection with 0-10V analog sensors

The 2-wire analog sensor requires pull-up resistor.

You can connect up to 2 analog sensors to IN1/IN2 terminals.

1. Disconnect power.

2. Connect with the diagram below:

VDD

GND OUT0-10V

0-10V

VDD

GND OUT

12/24V DC

GND

IN3

IN4

IN1

GND

IN2

12V

Diagram 5: Example connection with 4 0-10V analog sensors

(1 – power supply, 2 – switch, 6 – 0-10V analog sensor, 7 – con-

gurable pull-up resistors)

3. Verify correctness of connection.

4. Power the device.

5. Add the device to the Z-Wave network.

6. Change values of parameters:

• Connected to IN1:

»Does not require pull-up: change parameter 20 to 0

»Requires pull-up: change parameter 20 to 1

• Connected to IN2:

»Does not require pull-up: change parameter 21 to 0

»Requires pull-up: change parameter 21 to 1

• Connected to IN3:

»Does not require pull-up: change parameter 22 to 0

»Requires pull-up: change parameter 22 to 1

• Connected to IN4:

»Does not require pull-up: change parameter 23 to 0

»Requires pull-up: change parameter 23 to 1

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali FIBARO Controllori

FIBARO

FIBARO ROLLER SHUTTER 2 Manuale utente

FIBARO

FIBARO THE BUTTON Manuale utente

FIBARO

FIBARO KEYFOB FGKF-601 Manuale utente

FIBARO

FIBARO FIBEFGWCEU-201-B Manuale utente

FIBARO

FIBARO FGPB-101 Manuale utente

FIBARO

FIBARO FGS-214 Manuale utente

FIBARO

FIBARO ROLLER SHUTTER 2 Manuale utente

FIBARO

FIBARO FGPB-101-5 Manuale utente

FIBARO

FIBARO FGRGBWM-441 Manuale utente

FIBARO

FIBARO FGBHRGBW-041-1 Manuale utente

FIBARO

FIBARO Home Center Lite Manuale utente

FIBARO

FIBARO SWIPE FGGC-001 Manuale utente

FIBARO

FIBARO SWIPE FGGC-001 Manuale utente

FIBARO

FIBARO FGPB-101 Manuale utente

FIBARO

FIBARO WALLI FGWCEU-201 Manuale utente

FIBARO

FIBARO RGBW Controller Manuale utente

FIBARO

FIBARO FGPB-101 Manuale utente

FIBARO

FIBARO FGRGBW-442 Manuale utente

FIBARO

FIBARO ROLLER SHUTTER 3 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente