Fiberme FAG410X Manuale di istruzioni
FIBERME Communications LLC.
Configuring FAG410X with Grandstream UCM620X
P a g e 1
Table of Contents
OVERVIEW..................................................................................................................... 3
CONNECT UCM620X TO FAG410X USING PEER SIP TRUNK................................... 4
Create IVR On UCM620X..........................................................................................................................................4
Create Peer SIP TRUNK On UCM620X.......................................................................................................5
Configure Outbound Rule On UCM620X................................................................................................................5
Configure Inbound Rule On UCM620X...................................................................................................................6
Connect FAG410X with UCM620X..........................................................................................................................7
Configure FXO Port on FAG410X.................................................................................................................8
Create Port Group on FAG410X...................................................................................................................9
REGISTER FAG410X ON UCM620X AS AN EXTENSION...............................................10
Create SIP Extension on UCM620X..................................................................................................................... 10
Configure FAG410X SIP Account as a Registered Extension on UCM620X................................................. 10
FAG410X CALL Routing ............................................................................................. 12
Configure IP to Tel on FAG410X .......................................................................................................................... 12
Configure TEL to IP on FAG410X...............................................................................................................13
P a g e 2
Table of Figures
Figure 1: Create IVR 7000 on the UCM620X ...........................................................................................................4
Figure 2: Create Peer SIP Trunk on the UCM620X.................................................................................................5
Figure 3: Configure Outbound Rule on the UCM620X............................................................................................6
Figure 4: Configure Inbound Rule on UCM620X......................................................................................................7
Figure 5: Connect FAG410X with UCM620X: Registrar IP Address.....................................................................7
Figure 6: Connect FAG410X with UCM620X: Register Gateway..........................................................................8
Figure 7: Configure FXO Port on FAG410X: Modify Port.......................................................................................8
Figure 8: Configure FXO Port on FAG410X: Port Configurations .........................................................................8
Figure 9: Create Port Group on FAG410X: Add New..............................................................................................9
Figure 10: Create Port Group on FAG410X: Group Configurations......................................................................9
Figure 11: Create SIP Extension on UCM620X .......................................................................................................10
Figure 12: FAG410X SIP Account Settings ..............................................................................................................10
Figure 13: FAG410X Registrar IP Address...............................................................................................................11
Figure 14: UCM620X - SIP Extension Status...........................................................................................................11
Figure 15: FAG410X –IP to TEL................................................................................................................................12
Figure 16: IP to TEL Settings......................................................................................................................................12
Figure 17: FAG410X –TEL to IP................................................................................................................................13
Figure 18: TEL to IP Settings......................................................................................................................................13
P a g e 3
OVERVIEW
This document describes basic configuration to interconnect UCM620X series and FAG410X. In this
document, we are using FAG4108 as an example. The following methodology can be used for the FAG4104
as well. This is typically applied to the scenario where users would like to add a FAG410X not only as a
remote extension but also as an external PSTN trunk.
There are two ways to set up the UCM620X series IP PBX with the FAG410X.
•
Method 1: Configure FAG410X as a SIP Peer Trunk.
•
Method 2: Register FAG410X on the UCM620X directly as an extension.
Warning:
When using the IVR in UCM620X series, please be aware that if "Dial Trunk" option is turned on in IVR
settings, the call into the IVR will be able to dial outbound call using UCM620X's trunk. TheIVR's
permission level will be used when making outbound calls in this case. Please select properpermission
level for the IVR to control the outbound calls allowed via "Dial Trunk".
P a g e 4
CONNECT UCM620X TO FAG410X USING PEER SIP TRUNK
Create IVR On UCM620X
On the UCM620X web GUI, create an IVR extension under Call Features->IVR.
In IVR settings, if "Dial Other Extensions" is enabled, the calls dialing into the UCM620X IVR will be able
to
reach the internal extensions registered to the UCM620X. Also, you can assign the "Key Pressing Event"
to
different destinations.
Figure 1: Create IVR 7000 on the UCM620X
P a g e 5
Create Peer SIP TRUNK On UCM620X
On the UCM620X web GUI, create a peer SIP trunk under
Extension/Trunk ->VOIP Trunks.
In this example,
the FAG410X IP address is 192.168.99.239.
Figure 2: Create Peer SIP Trunk on the UCM620X
Configure Outbound Rule on UCM620X
On the UCM620X web GUI, go to
Extension/Trunk ->Outbound Routes
to create a new outbound rule. This
would allow the extension on the UCM620X to reach numbers in PSTN network via the peer SIP trunk we just
configured.
P a g e 6
Figure 3: Configure Outbound Rule on the UCM620X
In this example pattern "91XXXXXXXXXX", 9 is the first dialing digit and it will be stripped off when the call
goes out.
Configure Inbound Rule on UCM620X
On the UCM620X web GUI, go to Extension/Trunk ->Inbound Rules to create a new inbound rule. In this
example, we create the DID as 20000, which will be used in the FAG410X call forward setting.
P a g e 7
Figure 4: Configure Inbound Rule on UCM620X
The default destination is configured to IVR. Ensure to select the proper extension for the IVR.
Connect FAG410X with UCM620X
1.
On the FAG410X web GUI, go to the VoIP->SIP page and enterthe IP address of the UCM620X that
you are peering with.
Figure 5: Connect FAG410X with UCM620X: Registrar IP Address
2.
Please make sure the Register Gateway option under VoIP-> SIP is set to No. In the following
example, UCM620X has IP address 192.168.5.250.
P a g e 8
Figure 6: Connect FAG410X with UCM620X: Register Gateway
Configure FXO Port on FAG410X
1. Connect the PSTN line to the FAG410X FXO port.
2. On the FAG410X web GUI, go to the Port->FXO page and press Modify on the FXO port you will
use.
Figure 7: Configure FXO Port on FAG410X: Modify Port
3. Enter the SIP Account Number 20000 to be matched with the DID number we configured in
UCM620X Inbound Route.
Figure 8: Configure FXO Port on FAG410X: Port Configurations
P a g e 9
Create Port Group on FAG410X
1. On the FAG410X web GUI, go to the Port->Port Group page and press “Add New”.
Figure 9: Create Port Group on FAG410X: Add New
2. Select the FXO port you will use.
Figure 10: Create Port Group on FAG410X: Group Configurations
Altri manuali per FAG410X
4
Indice
Altri manuali Fiberme Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
