FibroLAN Falcon-MX/G/428/A Scheda tecnica

Falcon

Product Technical Note

PTP Grandmaster Configuration

Profiles: G.8275.1, G.8257.2, G.8265.1

T e c h N o t e : P T P G r a n d m a s t e r C o n f i g u r a t i o n

2 | P a g e

Administrative Information

Applicable models

Part Number

Applicable software version

Falcon-MX/G/428/A

7122

7.4.22 and above

Falcon-MX/G/428/D

7123

7.4.22 and above

µFalcon-MX/G

7143

7.4.22 and above

Document Management

Document Type

Technical Note

Source File Name

Fibrolan-TN_GM_PTP_Configuration_V1.4-2021-04-02.Docx

Created

Document version

Date

Idan Reshef

1.4

02/04/2021

Modified

Document version

Date

Proprietary Information. This document contains information, which is proprietary to Fibrolan

Ltd. No part of its contents may be used, copied, disclosed or conveyed to a third party in any

manner whatsoever without prior written permission from Fibrolan Ltd.

www.fibrolan.com

T e c h N o t e : P T P G r a n d m a s t e r C o n f i g u r a t i o n

3 | P a g e

PTP Grandmaster Configuration

This guide briefly describes how to configure Falcon-MX/G and µFalcon-MX/G to operate as a

PTP Grandmaster in compliance with ITU-T G.8275.1, G.8275.2 and G.8265.1 profiles. To

properly source and propagate timing signal the µFalcon-MX/G must first be installed and

connected to a GNSS antenna (for details on antenna installation refer to Technical Note:

GPS/GNSS Antenna Installation Guidelines on www.fibrolan.com Resources webpage).

1Physical Description

The M Class Falcon /G models are high-performance Carrier Ethernet switches, which includes

highly comprehensive Timing and Synchronization capabilities. The M Class Falcon Grandmaster

models are available in two form factors:

•Falcon-MX/G: 19” 1RU size

•µFalcon-MX/G: ½ 19” 1RU size

1.1 Falcon-MX/G

①

24x 100/1000 BaseX

⑧

LEDs indicators Link/Activity (per port)

②

4x 10/100/1000 BaseT

⑨

2x Sync SMA input/output –1PPS/10 MHz

③

4x 1/10G BaseX

⑩

RJ45 input/output ToD/1PPS

④

RJ45 and USB Console

⑪

LEDs indicators CPU/Alarm

⑤

GNSS antenna TNC connector (5VDC)

⑫

Expansion module for Rubidium clock

⑥

1.5 / 2 Mbps BITS input/output

⑬

PSU1 –AC/DC options supported

⑦

LEDs indicators PSU1/PSU2

⑭

PSU2 –AC/DC options supported

1.2 µFalcon-MX/G

①

4x 100/1000 BaseX

⑦

LEDs indicators Power/CPU/Sync/GNSS

②

2x 10/100/1000 BaseT

⑧

LEDs indicators Link/Activity (per port)

③

2x 1/10G BaseX

⑨

2x Sync SMA input/output –1PPS/10 MHz

④

USB Console

⑩

RJ45 input/output ToD/1PPS

⑤

GNSS antenna TNC connector (5VDC)

⑪

Dual 20÷60 VDC inputs

⑥

1.5 / 2 Mbps BITS input/output

⑫

Ground

T e c h N o t e : P T P G r a n d m a s t e r C o n f i g u r a t i o n

4 | P a g e

2Configuration Steps

2.1 Initial Settings

Before starting with the Timing configuration ensure proper management access via web GUI.

Detailed information on system turnup can be found in the Falcon M class Getting Started quick

guide that can be found in www.fibrolan.com.

2.2 GPS/GNSS Signal

Additional prerequisite is to assure a proper satellite signal. To do that hit the GPS/GNSS port

on the front panel at the GUI home page. This will lead to the GPS/GNSS monitor screen.

Verify the GPS/GNSS module is locked on the incoming signal, no alarms are present and there

is good visibility of satellites in the sky.

2.3 Setting up the SyncCenter

•Hit the SyncCenter button at the GUI top right corner.

•In the SyncCeter page enable source 1 and set it to GPS, as shown below, then press the

Apply at the bottom of the page.

T e c h N o t e : P T P G r a n d m a s t e r C o n f i g u r a t i o n

5 | P a g e

3PTP Configuration

3.1 G.8275.1 Profile

This Precision time protocol telecom profile is intended for phase/time synchronization with full

timing support network. This is an Ethernet multicast profile (layer 2 transport)

•Hit the PTP link from the left side menu: Configuration>Timing>PTP

•Create a new PTP Clock instance and set it to Masteronly type and G.8275.1 Profile.

•Follow the hyperlink of the instance number to the next configuration page.

•Enable the relevant physical interface by checking the checkboxes of the relevant ports.

Notes:

1. G.8275.1 profile default settings are:

•Transport layer: Ethernet

•PTP Domain number: 24

•Message frame rates:

oAnnounce: (-3) or 8/sec

oSync: (-4) or 16/sec

oDelay Response: (-4) or 16/sec

2. Message frame rates can be modified by pressing the “Ports Configuration” link if needed.

3. This profile uses Multicast transmission, packets will be sent on any enabled port, regardless

of whether there is a slave connected to it or not.

T e c h N o t e : P T P G r a n d m a s t e r C o n f i g u r a t i o n

6 | P a g e

•Apply the configuration by pressing the Apply at the bottom of the page.

3.2 G.8275.2 Profile

This Precision time protocol telecom profile is intended for phase/time synchronization with

partial timing support network. This is an UDP/IP unicast profile (layer 3 transport)

•Hit the PTP link from the left side menu: Configuration>Timing>PTP

•Create a new PTP Clock instance and set it to Masteronly type and G.8275.2Profile.

•Follow the hyperlink of the instance number to the next configuration page.

•Enable the relevant physical interface by checking the checkboxes of the relevant ports.

Notes:

1. G.8275.2 profile default settings are:

•Transport layer: IPv4 Unicast

•PTP Domain number: 44

•Message frame rates:

oAnnounce: (-3) or 8/sec

oSync: (-7) or 128/sec

oDelay Response: (-7) or 128/sec

2. In unicast profiles message rates are requested by slave device in dedicated signaling

3. Maximum message rates can be enforced on the Grandmaster per port by pressing the

“Ports Configuration”.

T e c h N o t e : P T P G r a n d m a s t e r C o n f i g u r a t i o n

7 | P a g e

•Apply the configuration by pressing the Apply at the bottom of the page.

3.3 G.8265.1 Profile

This Precision time protocol telecom profile is intended for frequency synchronization. This is

an UDP/IP unicast profile (layer 3 transport)

•Hit the PTP link from the left side menu: Configuration>Timing>PTP

•Create a new PTP Clock instance and set it to Masteronly type and G.8265.1Profile.

•Follow the hyperlink of the instance number to the next configuration page.

•Enable the relevant physical interface by checking the checkboxes of the relevant ports.

Notes:

1. G.8265.1 profile default settings are:

•Transport layer: IPv4 Unicast

•PTP Domain number: 4

•Message frame rates:

oAnnounce: (-3) or 8/sec

oSync: (-7) or 128/sec

oDelay Response: (-7) or 128/sec

2. In unicast profiles message rates are requested by slave device in dedicated signaling

3. Maximum message rates can be enforced on the Grandmaster per port by pressing the

“Ports Configuration”.

T e c h N o t e : P T P G r a n d m a s t e r C o n f i g u r a t i o n

8 | P a g e

•Apply the configuration by pressing the Apply at the bottom of the page.

•Save the configuration by hitting the Save button at the GUI top left corner.

Notes:

1. All Ethernet ports (1-24 and 29-32 on Falcon, 1-8 on µFalcon models) support PTP and SyncE

simultaneously

2. Falcon-MX/G copper port (25-28) are management ports and do not support PTP nor SyncE.

3. Internal ports (33-37 on Falcon, 9-11 on µFalcon models) may be ignored.

4. The default parameters of the profile may be modified as needed (but take care to avoid

misconfiguration)

5. If needed PTP messages can be tagged by setting the port mode to Trunk

6. For more complex or atypical configurations, please Contact Us.

T e c h N o t e : P T P G r a n d m a s t e r C o n f i g u r a t i o n

9 | P a g e

We’ve got Timing for you!

Intl. Headquarters

Fibrolan Ltd.

Tel: +972-4-959-1717

Fax: +972-4-959-1718

[email protected]om

www.fibrolan.com

North America

Fibrolan Inc.

Tel: +1-201-843-1626

Fax: +1-201-843-1628

[email protected]om

www.fibrolan.com

Central-Eastern Europe

Fibrolan CEE GmbH.

Tel: +43-2253-21188-88

Fax: +43-2253-21188-99

[email protected]

www.fibrolan.at

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali FibroLAN Hardware di rete

FibroLAN

FibroLAN Falcon-RX/812/G/A Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente