Field Controls SWG-4HD Manuale utente

www.eldcontrols.com

Please retain these instructions after installation.

This device MUST be installed by a qualied agency in accordance with the manufacturer's installation instructions. The denition of

a qualied agency is: any individual, rm, corporation or company which either in person or through a representative is engaged

in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the

precautions required, and has complied with all the requirements of the authority having jurisdiction.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.

Installation Date:

Installed By: Phone:

REPAIR MOTOR KIT

Model: SWG-4HD, SWGII-4HD, SWG-5,

SWGII-5, SWG-6, SWGII-6

This kit includes a replacement assembly for the SWG and SWGII series sidewall power

venter models listed above.

NOTE: Before working on power venter, shut o electrical power to control box.

ITEMS INCLUDED:

1- Replacement Motor and Blower Wheel on Mounting Bracket with Mounting Fasteners

1- 1⁄8" Hex wrench

1- Instruction Sheet

P/N 46252300 Rev I 12/21

page 2

Figure 1

ELECTRICAL BOX

WIRE NUTS

ELECTRICAL BOX COVER

Figure 2

IDENTIFY WHICH MODEL POWER VENTER YOU HAVE

CAUTION: Avoid applying excess pressure on the blower wheel when handling. This will cause an imbalance

of the blower wheel which will result in excessive vibration and premature motor failure.

REMOVAL

1. Remove motor cover. (See Figure 1)

2. Remove the electrical box cover and disconnect the conduit and wires. (See Figure 2) It is not necessary

to disconnect the wires from the Control Kit.

3. Remove the nuts securing the motor assembly, and pull the motor assembly straight o of the unit.

(See Figure 3)

4. Clean o any build-up inside the blower wheel housing.

P/N 46252300 Rev I 12/21

page 3

INSTALLATION

1. Align the holes in the circular cover plate with the holes in the motor mount bracket on the motor

assembly. (See Figure 3)

2. Slide the motor assembly onto the protruding threaded studs on the power venter body with the exhaust

chute pointing downward, and replace the nuts securely to the threaded studs. (See Figure 3)

3. Use the top knockout on the electrical box and reattach the exible conduit and wires to the motor using

the conduit connector and wire nuts. Secure the cover on the electrical box.

4. Seal around the edge of the motor mount bracket with high temperature silicone sealant. Install the motor

cover with the side louvers pointing downward. (See Figure 1)

Figure 3

P/N 46252300 Rev I 12/21

Phone: 252.522.3031 • Fax: 252.522.0214

www.fieldcontrols.com

This manual may be downloaded and printed from the Field Controls website (www.eldcontrols.com)

WARRANTY

For warranty information about this or any Field Controls product, visit:

www.eldcontrols.com

Field Controls Technical Support

1.800.742.8368

eldtec@eldcontrols.com

Altri manuali per SWG-4HD

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Field Controls Motore

Field Controls

Field Controls SWG Manuale utente

Manuali Motore popolari di altre marche

Rotax

Rotax 125 senior MAX evo Manuale utente

Kohler

Kohler K361 Manuale utente

MTD

MTD OHV Series Manuale utente

Kohler

Kohler COMMAND CH18-745 Manuale utente

Mercury

Mercury D4.2L D-Tronic Manuale utente

Selve

Selve SE Plus-RC Series Manuale utente

Perkins

Perkins 1206E-E66TA Manuale utente

Skov

Skov DA 174 Manuale

Rossi

Rossi TX11 Series Manuale utente

Siemens

Siemens SIMOTICS T-1FW3 Foglio di istruzioni

AL-KO

AL-KO PRO 350 Manuale utente

MTU

MTU 12 V 4000 Lx4 Manuale utente

Nanni

Nanni N3.30 Manuale di istruzioni

Nanni

Nanni N5.160 CR2 Manuale utente

KSB

KSB SuPreme Series Istruzioni per l'installazione

Hiwin

Hiwin EM1 Series Manuale utente

Rotax

Rotax 912 i series Istruzioni operative

Siemens

Siemens SIMOTICS XP 1MB1 Manuale utente