Fife CDP-01 Manuale utente
04-09-02 CDP-01 Figure Sheet 1-834-A
CDP-01
Additional Instruction Manual
For Armless Recoiler Application (Variable Ratio)
(Programs: 100068-02X, 100070-02X, 100094-02X and 100118-02X)
04-09-02 CDP-01 Figure Sheet 1-834-A
COPYRIGHT i
NOTE
These additional instructions explain the special features of the system delivered to the customer. They
are intended for being used in conjunction with the CDP-01 Reference Manual. The CDP-01 Reference
Manual applies except as noted to the contrary in these instructions.
Copyright:
All rights reserved. Any reproduction of this Additional Instruction Manual, in any form, in whole or in part,
requires the prior written consent of FIFE.
The information given in this Additional Instruction Manual is subject to change without notice.
We have compiled this Additional Instruction Manual with the greatest possible care and attention:
however, the possibility of error can not be completely excluded. FIFE accepts no legal liability for
incorrect information given and the consequences arising therefrom.
Copyright 1996 FIFE Corporation, P.O. Box 26508, Oklahoma City, OK 73126, U.S.A.
FIFE GmbH,Postfach 1240, D-65762 Kelkheim/Ts., Germany
04-09-02 CDP-01 Figure Sheet 1-834-A
04-09-02 CDP-01 Figure Sheet 1-834-A
CONTENTS iii
04-09-02 CDP-01 Figure Sheet 1-834-A
TABLE OF CONTENTS
GENERAL INTRODUCTION 1
APPLICATION DESCRIPTION ..............................................................................................1-1
SOFTWARE PART NUMBERS .............................................................................................1-1
CONNECTING THE SYSTEM COMPONENTS ....................................................................1-1
OVERVIEW OF FUNCTION 2
OPERATOR CONTROL OPTIONS .......................................................................................2-1
SPECIAL FEATURES OF EXTERNAL CONTROL ...............................................................2-1
INPUT MATRIX - EXTERNAL CONTROL .............................................................................2-2
EXPLANATION OF THE OPERATING MODES .........................................................2-3 to 2-5
START UP / SENSOR POSITION TRANSDUCER CALIBRATION......................................2-6
START UP / GUIDE POSITION TRANSDUCER CALIBRATION.......................................... 2-7
START UP / SENSOR POSITIONER TO MANDREL RATIO CALIBRATION ......................2-8
START UP / GUIDING SENSOR CALIBRATION..................................................................2-9
START UP / SENSOR DRIVE POLARITY...........................................................................2-10
START UP / MANDREL DRIVE POLARITY ........................................................................2-11
TROUBLESHOOTING 3
FAULT DIAGNOSIS - FAULT RECTIFICATION.................................................................... 3-1
04-09-02 CDP-01 Figure Sheet 1-834-A
SUPPLEMENTARY OPERATING MANUAL 1
-11
04-09-02 CDP-01 Figure Sheet 1-834-A
GENERAL INTRODUCTION
Application description
Application is an Armless Recoiler that uses linear analog position feedback for both the mandrel
and the sensor positioner. The mandrel to sensor positioner ratio is programmable. External
control is required. When placed in automatic mode, the sensor seeks the web edge. The
sensor follows the web edge as long as selected. Once Automatic is selected the sensor position
and the mandrel position are recorded. The sensor continues to follow the web edge and the
mandrel then follows the sensor positioner.
A CDP-01-MH or CDP-01-MHH is used for this application. If a CDP-01-MH is used, the sensor
positioner is connected to drive 1 and the mandrel is connected to drive 2. If a CDP-01-MHH is
used, drive 1 is not used, the mandrel is connected to drive 2, and the sensor positioner is
connected to drive 3.
Software part numbers
The software part numbers are located on the side of the CDP-01 housing. They include the
Matrix Setup no. (MS) , State Machine no. (SM) and firmware version ( Dx ).
CDP version: CDP-01-MH D1:5650xx-02x MS: 100068.02x Please quote these
D2:5650xx-02x SM: 100069.02x details with all inquiries.
D3:5650xx-02x FIFE USA
CDP version: CDP-01-MHH D1:5650xx-02x MS: 100070.02x
D2:5650xx-02x SM: 100071.02x
D3:5650xx-02x FIFE USA
CDP version: CDP-01-MHH D1:5650xx-02x MS: 100094.02x
D2:5650xx-02x SM: 100095.02x
D3:5650xx-02x FIFE USA
CDP version: CDP-01-MHH D1:5650xx-02x MS: 100118.02x
D2:5650xx-02x SM: 100119.02x
D3:5650xx-02x FIFE USA
SUPPLEMENTARY OPERATING MANUAL 1
1-2
Connecting the system components
The system components are to be connected according to the Cable Connection Diagram
contained in the documentation.
04-09-02 CDP-01 Figure Sheet 1-834-A
SUPPLEMENTARY OPERATING MANUAL 1
1-3
04-09-02 CDP-01 Figure Sheet 1-834-A
SUPPLEMENTARY OPERATING MANUAL 2
-12
04-09-02 CDP-01 Figure Sheet 1-834-A
OVERVIEW OF FUNCTION
Operator control options
The CDP-01 signal amplifier can be operated by way of the CDP-01 control panel (internal
operation) for setup purposes only. For normal operational control, the parallel port must be
used. Control is to be supplied from a remote control panel or programmable logic controller.
The symbols below are used for the various operator control options in the following:
Internal operation
External operation
Special features of external control
When the operation modes are being controlled via
external control, the Automatic, Servo-Center, Manual
keys of the CDP-01 control panel are disabled.
If the cable to the parallel port ( -X7 ) of the CDP-01 is
disconnected, the operation mode is changed to Manual
mode.
Altri manuali per CDP-01
9
Indice
Altri manuali Fife Controllori
