Finelite HP-2 Manuale utente
Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com
1
HP-2 Recessed 1" T-Bar to Visible Flange Installation Instructions
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
© 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98302 V3. 01/17
2-3/4"
Diffuser
Corner Joiner
A
Step 1
Remove diffuser from corner joiner luminaire and set aside to prevent it from
getting dirty or damaged. Add 1/2" to body/row length (A), +/- 1/16" to simplify
installation. Luminaire needs to be installed next to support blocking.
Ceiling
Corner Joiner
1/4"-20 Threaded Rod Hole
Wall
Step 4
Make sure visible flange is flush with ceiling T-Bar.
1/4"-20 Threaded
Rod Hole
Feed Hole
2-1/4"
3/4"
5" Mounting
Location
0 - 10V
Dimming
Scan QR code for
helpful video(s) Step 2
Remove back plate clips (provided) to release back plates.
We recommend using a flat head screwdriver to get them
loose. CA TION: Do not lose these pieces.
Back Plate Clip
Step 3
Slowly swing down back plates from all luminaires. CA TION: Do not twist
back plate when swinging down - it will come out of the support extrusion.
Note that the screw shown is the pivot point and the back plate can be slid a
few inches either way for ease of access to the driver space.
Pivot Point
A. Secure corner joiner by installing 1/4" washers (by others) and 1/4"-20 nuts (by others) onto 1/4"-20 threaded
rod (by others).
1/4" Washer
(by others)
1/4"-20 Nut
(by others)
1/4"-20 Threaded Rod
(by others)
Step 5
1/4"-20 Threaded
Rod (by others)
Drywall Drywall
1/4"-20 Nut
(by others)
Luminaire
Support
Blocking
(by others)
Support
Blocking
(by others)
Starter oiner/Ender
A + 1/2" +/- 1/16"
Cutout Dimension
2-3/4"
4"
Ceiling Joiner
Diffuser
Step 6
Plug-Together Wiring
Ceiling Joiner
Wall
Corner Joiner
Step 7
Remove diffuser from recessed 1" T-Bar joiner luminaire and set
aside to prevent it from getting dirty or damaged.
Place joiner luminaire on T-Bar.
Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com
2
HP-2 Recessed 1" T-Bar to Visible Flange Installation Instructions
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
© 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98302 V3. 01/17
Wall
T-Bar
Joiner Bracket
Ceiling Joiner
Corner Joiner
Step 8
#10-32 x 5/8"
Screws (2)
(provided)
Corner Joiner
Ceiling Joiner Yoke Brackets x2 (provided)
Step 9
Align joiner bracket with corner joiner. Slide ceiling joiner towards corner joiner. IMPORTANT STEP: Secure joint with two yoke brackets (provided) using #10-32 x 5/8"
screws (provided). CA TION: When installed correctly these brackets will pull luminaires
together to make a tight joint. Do not over-tighten.
Plug-Together Wiring
Corner Joiner
Ceiling
Wall
Ceiling Joiner
Connect plug-together wiring.
Step 10
B. Alternate mounting option – Install 1/4" screw (by others) through mounting hole into proper structurally supported
blocking (by others).
Alternate 1/4" Screw
Mounting Option
ALTERNATE MO NTING OPTION
1/4" Screws
(by others)
Drywall Drywall
Support
Blocking
(by others)
Support
Blocking
(by others)
Support Blocking
(by others)
IMPORTANT STEP
Wires
Splice box door
Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com
3
HP-2 Recessed 1" T-Bar to Visible Flange Installation Instructions
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
© 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98302 V3. 01/17
Diffuser
Diffuser
Wall
Ceiling
Ceiling Joiner
Corner Joiner
Replace diffusers and turn power on to luminaires.
Conduit Plate
Wires
Wires
Conduit Plate
Jam Nut
Conduit
Run power cables through conduit plate and jam nut. Make electrical
connections. Secure conduit onto conduit plate with jam nut, and
reinstall conduit plate carefully not to damage any wiring.
Open optional splice box door to access wiring.
Step 13
Step 14 Step 15
Wires
Splice Box Door
Jam Nut
Conduit
OPTIONAL SPLICE BOX OPTIONAL SPLICE BOX
Remove conduit plate from ceiling joiner luminaire.
Run power cable through knock-out. Make electrical
connections. Secure conduit on to splice box with jam
nut and close splice box door.
T-Bar Bracket (provided)
Tie-wire (by others)
#8-18 x 1/4" Screws
(4) (provided)
#6-20 x 1/2" Self
Drilling Screws (4)
(provided)
Wall
Ceiling
Ceiling Joiner
Corner Joiner
Back Plates
Step 11 Step 12
Replace all back plates by holding them in their original position and pushing the clips back
in. Make sure wire connections are not pinched. (If 1 ft. back plate assembly is near joint,
reconnect feed harness to LED board.
Install T-Bar brackets (provided) onto ceiling joiner with #8-18 x 1/4" screws (provided).
Secure luminaire to T-Bar with #6-20 x 1/2" self drilling screw (provided). Secure luminaire
to structure using tie-wire (by others), as per code.
#8-18 x 1/4" Screws
(4) (provided)
#6-20 x 1/2" Self
Drilling Screws (4)
(provided)
Back Plate Clip
Altri manuali per HP-2
7
Altri manuali Finelite Lanterna
Finelite
Finelite HP-6 Recessed Flush Diffuser Tech Zone 6"... Manuale utente
Finelite
Finelite HP-2 Manuale utente
Finelite
Finelite HP-2 Manuale utente
Finelite
Finelite HP-6 Recessed Flush Diffuser Tech Zone 6"... Manuale utente
Finelite
Finelite HP-4 Recessed Manuale utente
Finelite
Finelite 10WM series Manuale utente
Finelite
Finelite HP-6 Recessed Flush Diffuser Tech Zone 6"... Manuale utente
Finelite
Finelite HP-6 Recessed Flush Diffuser Tech Zone 6"... Manuale utente
Finelite
Finelite HP-2 Manuale utente
Finelite
Finelite E2-ID Istruzioni per l'installazione
