FingerTec 6600 Manuale utente
Copyright 2006 by FingerTec Worldwide Ltd. All rights reserved. LAST UPDATE 29 MAY 2006
Copyright 2006 by FingerTec Worldwide Ltd. All rights reserved. LAST UPDATE 29 MAY 2006
RELOCATE THE HANDLE OF KEYLOCK 6600
HARDWARE
RELOCATE THE HANDLE
OF KEYLOCK 6600
SUGGESTIONS & SOLUTIONS FOR HARDWARE
1
Copyright 2006 by FingerTec Worldwide Ltd. All rights reserved. LAST UPDATE 29 MAY 2006
RELOCATE THE HANDLE OF KEYLOCK 6600
This document guides you through the steps to change the handle of keylock
from using right hand to left hand. The lock shown in the following figure is
meant for right hand users.
Follow the steps below to relocate the handle of the reader.
Step 1
Unlock the ring at the end of the handle. Take the cover out from the handle.
Step 2
Disconnect the supply wire from the battery. Unscrew the screws located at the
upper and bottom of the handle.
2
Copyright 2006 by FingerTec Worldwide Ltd. All rights reserved. LAST UPDATE 29 MAY 2006
RELOCATE THE HANDLE OF KEYLOCK 6600
At the end of step 2:
Step 3
Take out the front panel by moving the handle towards you. Then turn to the
back of the front panel and unscrew all the 8 screws at the back.
3
Copyright 2006 by FingerTec Worldwide Ltd. All rights reserved. LAST UPDATE 29 MAY 2006
RELOCATE THE HANDLE OF KEYLOCK 6600
Step 4
Take out the O-ring at the bottom of the circuit board by using a screwdriver.
Remove the plat.
Step 5
Remove the washer and the plate below. You will get the results as below,
consist of two springs.
Step 6
Take out the small spring but be careful with the thick spring. Change the position
of the thick spring using mirror method.
For example,
MIRROR
During the changing process, take out the handle.
4
Copyright 2006 by FingerTec Worldwide Ltd. All rights reserved. LAST UPDATE 29 MAY 2006
RELOCATE THE HANDLE OF KEYLOCK 6600
Change this spring position.
Step 7
After changing the position of the spring, re-assemble the whole unit by reverse
the steps above.
Below are the result for the relocating handle.
Follow the steps below for other side of the reader.
a) Turn to the back of the handle and unscrew all the 4 screws to dismantle
the handle from the panel.
5
Copyright 2006 by FingerTec Worldwide Ltd. All rights reserved. LAST UPDATE 29 MAY 2006
RELOCATE THE HANDLE OF KEYLOCK 6600
b) Remove the washer from the plate. Be careful when removing both
item. Remember the position of the spring.
c) Use the same mirror method to relocate the spring.
d) Reassemble back all the parts from putting the plate and washer
back and screw all the 4 screws back to the panel. Then connect
the wire back to the battery.
Then, assemble to the door and lock the ring.
6
Indice
Altri manuali FingerTec Serratura della porta
FingerTec
FingerTec Keylock 7700 Manuale utente
FingerTec
FingerTec Q2i Manuale utente
FingerTec
FingerTec Q2 Manuale utente
FingerTec
FingerTec Face ID2 Manuale utente
FingerTec
FingerTec ML-10B Manuale utente
FingerTec
FingerTec R3 Manuale utente
FingerTec
FingerTec Keylock 8800 Manuale utente
FingerTec
FingerTec ML-10B Manuale utente
FingerTec
FingerTec FaceID 3 Manuale utente
