FingerTec AC100C Manuale utente
TCP/IP PORT (LAN)
POWER ADAPTER
PORT
RS484 PORT
2. RS485 Network Connection
1. RS485 Single Connection
RX+
RX-
RS232/ RS485
Data Converter
RX+
RX-
RS232/ RS485
Data Converter
RS232 PORT
RS232/RS485 SERIAL
CABLE PORT
USB PORT
Wall
4 feet / 1.2 meter
(recommended)
Step 1
Determine the Location and Positioning
of the Installation
• Avoid installing the terminals in locations that has contact with
a strong light source (e.g direct sunlight, spotlight, fluorescent
light, etc)
• Avoid installing the terminals in locations with high moisture or
condensation levels in the air
• The recommended installation height of the terminal from the
ground is 1.2 meters.
Step 2
Mounting of Terminals
A. MOUNT ON WALL
• After determining the height of the terminal from the ground
level and having made the relevant marks on the wall, based on
the measurements in Appendix I, drill the screws into the wall to
hang the terminal.
Installation Guide
We Make Things Easy
www.fingertec.com
AC100 Series
Fingerprint Time Attendance System
B. FLEXI- KIT
FingerTec offers flexi-kits for all its time attendance models. Attach
the terminal on the flexi-kit for convenience.
Step 3
Wiring for Power Supply
The power jack is positioned on top of the terminal, labeled
Power Adapter Port in the below diagram.
Please use the power adaptor provided in the package or alterna-
tively you can opt for a linear power supply with specifications of
5VDC 2A. Plug one point of the power adapter to the terminal and
the other end to the power outlet. Don’t exceed the recommended
voltage or current to avoid damaging the terminal.
Step 4
Setting Up Data Communications
(Skip this step if you are using USB ash disk to transfer data)
TCP/IP – LAN Connection
For TCP/IP connection, plug the special RJ45 jack into the TCP/IP
(LAN) Port of the terminal. Connect the other end (normal RJ45
jack) to the local area network hub or a PC. Configure the device
ID, IP address, subnet mask and Gateway in the terminal (refer to
the hardware user manual for details).
RS232 – Serial Port Connection
Plug the communication jack that is provided in the package to
connect to the communication port of the terminal. Select wires
with label RX, TX and GND, and connect the other end of these
wires to a DB9 female connector. Configure the device ID and
baudrate of the terminal (refer to the hardware user manual for
details). Use the normal RS232 cable to plug into the RS232 port
of the terminal.
RS485 – Serial Port Connection
Plug the communication jack that is provided in the package to
connect to the communication port of the terminal. Select wires
with label RS485+, RS485- and GND, and connect the other end
of these wires to an RS232/485 data converter. Connect the other
end of the data converter to a DB9 female connector. Configure
the device ID and baudrate of the terminal (refer to the hardware
user manual for details).
Step 5
Finalizing the installation
1. Check that all cable connections are plugged in correctly.
2. Attach the terminal on the wall
3. Switch on the power to the terminal.
4. Start using the terminal.
Other Accessories
Note: All Accessories are listed at http://accessory.fingertec.com
AdapTec
AdapTec TA
The AdapTec TA is a 5VDC power supply inclusive of a 110~240VAC
switching linear power. The AdapTec provides 5VDC power to the
FingerTec terminal and charges a 12VDC 7.0Ah backup battery si-
multaneously. During an event of a power failure, the backup bat-
tery will automatically provide power to the terminal.
Mini UPS
Mini UPS 5VDC
Mini UPS 5VDC is a mini portable backup power supply with 5VDC
output, supplying 5VDC power for FingerTec Time Attendance ter-
minals.
Enclosures
FingerTec offers enclosures to protect the terminals from being
meddled with by unauthorized persons.
Flexi Kit
A foldable stand for FingerTec products, simplifies installation and
makes it presentable. (Example on Step 2, B.)
D
O
O
R
L
O
C
K
T
I
M
E
R
Diameter
We Make Things Easy
Appendix I
Terminal Dimensions and Measurements
Front View of AC100 Series Rear End
Altri manuali per AC100C
8
Questo manuale è adatto per i seguenti modelli
2
Altri manuali FingerTec Attrezzatura di sicurezza
