First Choice ESCHER M40 Guida

SPARE PARTS DIAGRAM FOR

First Choice Group

Blakeney Way, Kingswood Lakeside

Cannock, Staffs, WS11 8LD

TEL: 01543 577778 FAX: 01543504141

Email: [email protected]

Web: www.firstchoice-cs.co.uk

Mixer

M40

M60

USE AND MAINTENANCE MANUAL

SPARE PARTS

SPIRAL MIXERS

WITH FIXED BOWL

MODEL

M40 M60

M40 PREMIUM M60 PREMIUM

A MACHINE DESIGNED AND CONSTRUCTED

FOR MIXING BREAD AND PASTRY DOUGH

FOREWORD

P.1 User, aim and use of the manual……………3

P.2 Machine marking data……………………..3

SECTION A General information

A.1 Warnings ………………………………3

A.2 General description of the machine ………..3

A.2.1 Work environment ……………………….3

A.2.2 Dismantling …………………………3

A.3 Unacceptable conditions of use ……………3

A.4 Cleaning …………………………………3

A.5 Reference standards ………………….4

A.6 Operators ……………………….4

SECTION B Information regarding machine use

B.1 Technical data ……………………………4

B.2 Transportation and handling ………………4

B.3 Installation –Preparation for commissioning….6

B.4 Normal and safety shutoff ……..…….6

B.5 Control panel ………….…………….7

SECTION C Information regarding maintenance

C.1 Maintenance ……………………………8

C.2 Adjusting belt tension for spiral rotation …….8

C.2.1 Model M40 –M60………………………...8

C.2.2 Model M40 PREMIUM –M60 PREMIUM….…...9

C.3 Adjusting belt tension for bowl rotation ….10

C.4 Wiring diagram for power supply ….. ………11

C.5 Wiring diagram for control panel …..……….12

C.6 Wiring diagram for assembly ……………13

C.7 Spare parts list for 415 V system…………..14

C.8 Spare parts list for control panel ………….15

SECTION D Mechanical parts

Table 1 Head group of model M -exploded view…16

List 1 Head group list of model M…………….17

Table 2 Head group of model M PREMIUM

-exploded view

……………………….18

List 2 Head group list of model M PREMIUM……19

List 3 Bowl group list……………..…………20

Table 3 Bowl group -exploded view ……………21

Table 4 Machine structure -exploded view………22

List 4 Machine structure list…………………23

SPARE PARTS ENQUIRY

Always mention:

•Machine model

•Serial number

•No. of reference table

⇒Position in the list of the spare part requested

⇒Piece description

⇒Quantity needed

⇒Code

ESCHER MIXERS srl

Via Lago di Vico, 37 tel. +039 0445 576692

36015 SCHIO (VI)

ITALY

fax +039 0445 577280

UK SUPERMARKETS SPECIFICATIONS

FOREWORD

P.1 USER, AIM AND USE OF MANUAL

This instructions booklet is directed to:

•the personnel in charge of the workshop and maintenance

•the personnel in charge of installation

•the user

•the personnel in charge of dismantling

The user must take care of the manual, ensuring that it is not damaged, and

furthermore provide a place for it to be kept which is both safe yet easily

accessible.

The manual is divided into four sections: one foreword and three sections

regarding safety, use and maintenance.

•FOREWORD: The manufacturer’s details and machine data, which must be

quoted in all situations, are recorded in this section.

•SECTION A: Regards safety regulations and information.

•SECTION B: Machine characteristics –operation –transportation –

assembly of equipment are described in this section.

•SECTION C: Includes information regarding maintenance, lubrication and

plant drawings.

For further information, either contact the manufacturer directly or the

authorised agent; always quote the details stamped on the machine plate.

P.2 MACHINE MARKING DATA

MODEL ____________

SERIAL NUMBER ____________

DATE OF MANUF. ____________

VOLTAGE ____________

FREQUENCY ____________

PHASES ____________

AMPS ____________

This booklet is the Instructions Manual for the machine referred to above and

has been compiled in conformance with the EEC Directive 89/392, Enclosure I,

paragraph 1.7.4.

SECTION A: GENERAL INFORMATION

A.1 WARNINGS

In order to ensure maximum working reliability, ESCHER MIXERS takes great care

in the choice of materials and components to be used in the construction of its

equipment, which is fully inspected and tested before consignment. The long term

efficiency of the machine also depends on its correct use and the proper

preventive maintenance as specified in the instructions described in this manual.

The manufacturer wishes to point out that:

•Every part of this manual must be carefully read and fully understood

before using or tampering with the machine.

•The machine must not be tampered with, altered or modified, even

partially, and in particular, the protection guards must not be removed.

•The machine must not be used in conditions or for use other than those

specified in this manual. The manufacturer shall not be held responsible for

breakdowns, malfunctions or accidents caused by the non-observance of this

rule.

The EC plate is located on the lower rear part of the machine.

A.2 GENERAL DESCRIPTION OF THE MACHINE

The machine has been designed and constructed for professional use with

foodstuffs.

The aim of the mixer is to obtain a well-blended mixture for both bread dough

and pastry.

The tables which include the technical data, use of the machine and command

functions can be found below, in Chapter B.4.

A.2.1 WORK ENVIRONMENT

Acceptable work values for good machine performance:

•Temperature: from +5° to +40°C, with an average which must not be

above 35°C in a 24 hour period.

•Relative humidity: between 30% and 95% (without condensation).

Provide opportunities and means for carrying out cleaning and maintenance

operations.

Isolate the machine so that untrained personnel cannot access it.

Noise emission in the worst possible conditions is less than 70 dB.

A.2.2 DISMANTLING

In the event that the machine is to be scrapped, its parts must be disposed of

separately, taking into consideration the different compositions of the various

parts, and according to the law regulating the disposal of industrial waste.

None of the components are classified as toxic-noxious products.

A.3 UNACCEPTABLE CONDITIONS OF USE

The obvious conditions in which to avoid using the machine could include:

•Load greater than the allowed amount.

•Tampering of the safety systems.

•Use of equipment that is not supplied with the machine, that is not

suitable for handling food or that could scratch the surface of the bowl.

•Using the machine in unsuitable environments.

A.4 CLEANING

As the machine is used for handling food, cleaning must be thorough and

carried out on a daily basis.

Use only water together with a non-abrasive sponge and a plastic spatula to

remove any residual incrustations.

The area surrounding the machine must be cleaned, and the machine must

regularly be moved so that the area under the machine can also be cleaned.

When moving the machine disconnect the plug from the power outlet and raise

the feet.

A.5 REFERENCE STANDARDS

The model of the machine described in this manual is in compliance with

Directive 89/392/EEC, with its amending directives and with reference to the

following standards:

•UNI EN 292-1, UNI EN 292-2. Basic concepts for machine safety and

general design principles.

•UNI EN 294 Safety distances.

•UNI EN 349 Minimum distance to prevent crushing.

•EN 60204-1 Electrotechnical aspects.

•EN 453 Machines for the production of food products –Mixers.

SECTION B: INFORMATION REGARDING MACHINE USE

B.1 TECHNICAL DATA

*) In this reference dough, the amount of water used is 60% with respect

to the amount of flour.

PACKAGED DIMENSIONS [cm]

carton

on pallet

wooden

crate

wooden

box

Length 138 125 125

Width 88 80 80

Height 174 155 155

A.6 OPERATORS

The machine has been designed and constructed for professional use. Therefore:

•The operator must be familiar with the control panel functions, the

installed safety systems and regularly check their efficiency. He must be

familiar with all possible work cycles and the quantity of product to use.

He must clean the machine every day.

•Technician in charge of ordinary maintenance (see point C.1) can be one

of the user’s technicians who inspects the command and safety devices and

regularly checks the condition of the belts.

•Technician in charge of extraordinary maintenance and repairs (see point

C.1), while the machine is under warranty, must be authorised by the

manufacturer.

Refer to the chapter on Maintenance (Sect. C).

B.2 TRANSPORTATION AND HANDLING

To lift the machine use suitable means and equipment, and avoid oscillations.

The machine is off-centre, therefore take note of the precautions indicated on

the specifications sheet affixed to the outside of the packaging. An example is

reproduced below.

DOUGH

CHARACTERISTICS BOWL CHARACTERISTICS MACHINE

CHARACTERISTICS MOTOR

CAPACITY SPEED PACKAGED WEIGHT

MODEL

max

capacity

max

flour

water*

volume

diameter

height

from ground

length

width

height

weight

spiral

I/II speed.

bowl

spiral

I/II speed.

bowl

carton

on pallet

wooden crate

wooden

box

kg kg llmm mm mm mm mm daN kw kw rpm rpm daN daN daN

M 40 40 25 15 80 560 913 1055

590 1360

350 2.1

3.7 0.55

116

237 13 365 390 420

M 40

PREMIUM 40 25 15 80 560 913 1055

590 1360

365 2.1

3.7 0.55

180 13 380 405 435

M 60 60 37 23 100 630 913 1140

660 1360

355 2.1

3.7 0.55

116

237 13 370 395 425

M 60

PREMIUM 60 37 23 100 630 913 1140

660 1360

370 2.1

3.7 0.55

180 13 385 410 440

1. LIFTING THE PACKAGED MACHINE

The machine is transported on a wooden pallet A,

secured by a cross bar C, and fastened to the pallet by

means of two threaded rods B.

To lift by means of a pallet transfer unit or lift truck,

insert the forks in the positions indicated in the figure.

Before lifting, check the suitability of the equipment.

NOTE:

The material used for packaging, apart from the threaded

rods and the bar, can be recycled or disposed of as

urban waste.

2. LIFTING THE UNPACKAGED MACHINE

By means of a belt

Positioned between the column and the end of the tool

holder shaft, as shown in the figure.

It is advisable to use a suitable space bar (e.g. a

wooden plank with a minimum section of 25x130 mm)

in order to keep the belt away from the cover so that

it is not damaged.

As the machine is decentred with respect to the point

of suspension the machine hangs in an off-balanced

position. In no way, however, does this effect the

safety of the operators or the machine.

NOTE:

Avoid oscillations during this operation.

By means of a lift truck

Insert the forks in the positions indicated.

Lift carefully keeping the forks in a horizontal position.

Fork position

Belt

position

Space bar

Fork

position

B.3 INSTALLATION –PREPARATION FOR COMMISSIONING

•The machine must be positioned in an area which is suitable for working with

foodstuffs and that can be thoroughly cleaned.

•It is not necessary to fasten the machine to the ground; however it must be levelled

by adjusting the front feet which at the same time lifts the front wheel from the floor.

•Check that the electric line is correctly connected by means of an approved plug.

•Check all the commands and that the mobile guard protection microswitch is

functioning correctly. Adjustment is carried out by the manufacturer.

The user must contact the authorised technician if adjustment is required.

•Before commissioning, check the maximum quantities of the product to be loaded into

the bowl, by consulting the tables in Chapter B.1 relevant to the model purchased.

B.4 NORMAL AND SAFETY SHUTOFF

1. NORMAL SHUTOFF

•In manual mode: Stop the machine by pressing the machine shutoff push

button.

•In automatic or semiautomatic mode: The machine is automatically shutoff by

the timers.

2. SAFETY SHUTOFF

•The machine shuts-off whenever the mobile guard is lifted from the bowl.

•NOTE:

In all cases rotation is stopped, even if gradually, in less than 4 seconds.

3. MOVING THE MACHINE BY HAND

The machine may need to be moved in order to clean the area

under it.

To move the machine :

Tighten the threaded rod of the foot Cwhich when it retracts allows

the front pivoting wheel B to touch the floor. The other two points

of support are the two rear fixed wheels A.

Caution:

•Disconnect the feed cable Dbefore beginning the procedure

described above.

•After returning the machine to its original position, ensure its

stability by loosening the two threaded feet C thereby raising

the front wheel B from the floor

•To power the control panel, activate the general switch E.

B.5 CONTROL PANEL

1Timer for first spiral tool speed

6Timer for second spiral tool speed

When the pointer is below zero, (display unlit), the timed shutoff

function is deactivated.

The LED, bottom right, when lit indicates whether the reading scale

is in seconds (s), minutes (m) or hours (h). To change the scale

consult the qualified technician.

2Start push button for first spiral speed

Does not function with the bowl cover open.

It permits three types of functions:

•MANUAL WORK MODE IN FIRST SPEED

(Timers 1and 6deactivated)

Shutoff by pressing stop push button 5.

•SEMIAUTOMATIC WORK MODE IN FIRST SPEED

(Timer 1activated, 6deactivated)

Shutoff is controlled by timer 1.

•AUTOMATIC WORK CYCLE

(Timers 1and 6 activated)

The following sequence is carried out automatically:

1. Timed work phase in first speed.

2. Bowl stops for 2 seconds.

3. Timed work phase in second speed.

4. Automatic machine shutoff.

3Power indicator

When lit, it indicates that the electrical board is powered.

4Bowl jog rotation command in first speed

Also functions with bowl cover open.

When the push button is released the bowl stops rotating.

5Machine emergency/stop push button

Interrupts all modes of rotation.

NOTE

If the cover is lifted while the machine is running, the machine shuts off, but

the timers memorise the actual time reached. Once the cover has been closed

again and the start buttons 2 pressed, the machine restarts and the timers

permit the rest of the work cycle to be completed.

This memory is not stored if the machine is shut off by means of stop push

button 5.

NUDGE

START

SECTION C: INFORMATION REGARDING MAINTENANCE

C.1 MAINTENANCE

1. ORDINARY: Includes:

•Daily cleaning

•Checking the belt tension ( monthly)

See chapter C.2 for operative methods.

•Checking the correct functioning of commands and safety devices

(every time it is turned on).

C.2 ADJUSTING BELT TENSION FOR SPIRAL ROTATION

The belt tension must be adjusted if, during a work cycle, the operator notices

a slowing down in the rotation of the spiral tool.

1. Remove the three side screws Vwhich secure the head guard T.

2. Lift the head guardTand disconnect the connector E.

3. Loosen the 4 screws Awhich secure the motor support plate (without

completely unscrewing them).

4. If necessary replace the belts:

•Loosen the two nuts B

•Tighten the two nuts C(in order to loosen the belts) and remove

them.

2. EXTRAORDINARY

This can be considered a preventive operation as well as an intervention

in the event of malfunctions and/or breakages.

These operations must be carried out by personnel authorised by the

manufacturer or by one of his direct resellers. In the event that the user

has specially trained personnel at his disposal, once the warranty has

expired, he can request the manufacturer provide him with more detailed

drawings and lists, as well as exploded views of the mechanical parts. In

this case the user is responsible for any damage caused to persons and/or

the machine.

After 2000 working hours: it is advisable to have a technician inspect the

bearings and the other transmission parts.

5. If necessary adjust the belt tension:

•To increase the tension:

Loosen the two nuts C.

Tighten the two nuts B.

•To decrease the tension:

Loosen the twonuts B.

Tighten the two nuts C.

C.2.1 ADJUSTMENT FOR MOD. M40 –M60

T1 TV

6. Tighten the four screws Awhich secure the motor support.

7. Reconnect the connector E.

8. Put the protection guard Tback into its correct position with regard to

the head T1.

9. Tighten the three screws V.

The belt tension must be adjusted if, during a work cycle, the operator notices

a slowing down in the rotation of the spiral tool.

1. Remove the three side screws Vwhich secure the guard.

2. Lift the head guardTand disconnect the connector E.

3. Loosen nut Cand the two nuts C1, to allow movement of both the

transmission pulley support and the motor support.

4. Loosen the 4 screws Dwhich support the spiral motor (without completely

removing them).

5. Loosen the four screws Aof the transmission pulley support ( without

completely removing them).

6. If the belts need to be replaced, proceed as follows:

•Loosen the two nuts B.

•Loosen nut F.

•Remove the upper transmission plate Lby loosening the 4 screws I.

Now the belts are loose and they can be replaced. Before replacing

them ensure that the new belts have the same characteristics as

the original ones.

Firstly remove belts Gand then belts H.

Replace belts Hand then belts G.

•Reposition the upper transmission plate Land secure it by means of

the four screws I.

7. If necessary adjust the tension of belts G:

•To decrease the tension, loosen the nut and tighten C.

•To increase the tension, tighten nut Fand loosen C.

8. Secure the transmission plate by means of the four screws A.

9. Tighten the nut C.

10. If necessary adjust the tension of the belts H:

•To decrease the tension, loosen nut B and tighten C1

•To increase the tension, tighten nut B and loosen C1

11. Secure the motor plate by means of the four screws D.

12. Tighten the two nuts C1.

13. Reconnect the connector E.

14. Put the guard Tback in its correct closed position with respect to the

head T1.

15. Tighten the three side screws V.

C.2.2 ADJUSTMENT FOR MOD. M40 PREMIUM–M60 PREMIUM

C3 ADJUSTING THE BELT TENSION FOR BOWL ROTATION

The belt tension must be adjusted if, during a work cycle, the operator notices

a slowing down in the rotation of the bowl.

1. To increase the tension of the transmission belts C:

Use a wrench to rotate nut Ain a clockwise direction.

2. To increase the tension of the motor belts D:

Use a wrench to rotate nut B in a clockwise direction.

3. To replace the belts:

The belt compartment can be accessed by removing the side door.

•Rotate nut Bin an anticlockwise direction

•Rotate nut Ain an anticlockwise direction

Note: Ensure that the new belts have the same characteristics as the

previous ones.

Bowl

shaft

Transmis. belts

( tr.pulleys –bowl

Motor belts

( motor–tr.pulleys

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali First Choice Miscelatore

First Choice

First Choice BV22 Manuale utente

Manuali Miscelatore popolari di altre marche

Bosch

Bosch GRW 9 Manuale utente

MULTIQUIP

MULTIQUIP Whiteman WM45E Guida

KitchenAid

KitchenAid KSM7581BZ0 Guida rapida

Jay-Lor

Jay-Lor 5050 Manuale utente

Sunbeam

Sunbeam FPSBSM210X Manuale utente

MULTIQUIP

MULTIQUIP Whiteman MC94S Guida

Thinky

Thinky ARE-250 Manuale utente

Midas

Midas XL4 Manuale utente

bianco

bianco PURO 4 Manuale utente

Paso

Paso DAG9200 Manuale utente

Sima

Sima SFX-9A Manuale utente

better chef

better chef IM-815WC Istruzioni per l'installazione

ALLEN & HEATH

ALLEN & HEATH GR1 Manuale utente

Lacor

Lacor 69083 Scheda tecnica

M-Audio

M-Audio Midiman SAM Manuale utente

Buffalo

Buffalo CP921 Manuale utente

Pentair

Pentair HYPRO Cleanload 3376-0870 Istruzioni operative

Cuisinart

Cuisinart SM50WHE Manuale utente