Firstech BLADE Series Manuale utente
CM-900
CM-900S/900AS
CM7X00
CM7000/7200 Cut loop for A/T
CM900AS/900S Jumper
DEREK ZOOLANDER
Est. 2001
CENTER KIDS
WHO CAN’T READ GOOD
A
N
D
W
H
O
W
A
N
N
A
L
E
A
R
N
T
O
D
O
O
T
H
E
R
S
T
U
F
F
G
O
O
D
T
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
for
Green White/BluePark / Auto
I/O Changes
HoodIGN
Lights
CANInstallYearModelMake
BLADE FEATURE COVERAGE
PARKING LIGHTS
SECURE TAKEOVER
GLOW PLUG STATUS
TACH OUTPUT
E-BRAKE STATUS
BRAKE STATUS
RAP SHUTDOWN
DOOR STATUS
DISARM OEM ALARM
ARM OEM ALARM
DOOR UNLOCK
DOOR LOCK
PRIORITY UNLOCK
IMMOBILIZER DATA
Ignition connection.
E
Ignition jumper, NO CONNECTION required.
D
Vehicle hood status ( - ).
C
Not required.
B
Required CAN connections.
A
Firmware: Covered vehicles use either BLADE-AL(DL)-CH8, confirm application, flash module, and update the controller
firmware before installing.
Install: Type 2 vehicles use the included CAN extension cable to source CAN data from the green CAN junction block
(left side of the dash) or from the BCM (pin#25, CANH, brown, pin #26, CANL, yellow).
Lighting: Type B parking lights use the 10-pin connector, secure unused 6-pin connector for safety.
Ignition: Common ignition provisions are listed in the BLADE diagram, ignition is also available at the vehicle BCM
(connector C5/E, pin #27, pink/white).
Hood: Hood status wire is available at the vehicle BCM, connector C1, pin #11 (violet/blue).
FTI-CDP1 - Installation and Configuration Notes
FTI-CDP1 - Vehicle Coverage and Preparation Notes
CONNECT TO PINK.
3500 TIP Start Diesel 2018 Type 2 CJB Type B BCM BCM
DL-CH8
RAM
Firstech
Techfeedtree
Diesel WTS
Set feature
option 4-10-4
pink
pink/black
PWR
BLADE
1
16
1
12 11
13
24
11
C1 - Hood pin ( - )
26 25
48
1
10
26 25
39
C5 - Ignition
27
O
F
F
A
C
C
R
U
N
S
T
A
R
T
violet/blue
HOOD
BCM
4
TIP Start Cylinder
2
OBD-II connector
1
3
Headlight switch
AUTO
pink
green
5
Green
Junction Block
*Not required
Type B
pink/white
or
brown
yellow
H
Driver side dash
H L
RAP SHUTDOWN
B
A
A
B
C
C
D
E
FTI-CDP1 - DL-CH8 - Type 2
1
2
3
4
LED Programming Error Codes
Module LED flashing RED during programming
1x - CAN Error, check CAN wiring and voltages
2x - Key code not learned, confirm unlock sent, check CAN
3x - No immobilizer data, check immo data connection
4x - No IGN, check IGN connection
5x - VIN not found, check CAN connections
6x - No immobilizer data, check immo data connection
7x - Not the same key, use only one key for programming
8x - No immobilizer data, check immo data connection
9x - No immobilizer data 10x - Klon error, redo Klon
2018 RAM 3500 TIP Start Diesel
Patent No. US 8,856,780 CA 2759622
INSTALL GUIDE
WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020
ALL IN ONE
DODGE/RAM
MODULE PROGRAMMING PROCEDURE - WITH KLON
9Turn key to ON position.
ON
4Turn key to ON position.
ON
15 Turn key to ON position.
ON
11 Turn key to OFF position.
OFF
6Turn key to OFF position.
OFF
17 Turn key to OFF position.
OFF
19 Turn key to OFF position.
OFF
20 Module Programming
Procedure completed.
1Close driver door.
Re-open driver door to wake up
data bus.
2Press UNLOCKon OEM remote.
If the vehicle is not equipped
with an OEM remote, press the
module programming button.
7Remove key.
8Insert key into ignition.
3Wait, LED will flash BLUE once
[1x].
5Wait, LED will turn solid RED.
10 Wait, LED will flash BLUE.
16 Wait, LED will turn solid BLUE
for 2 seconds.
14 WARNING: Do not press RS
programming button.
Connect power first.
Connect RS to vehicle.
13 Connect RS to computer
and proceed with extended
programming.
12 WARNING:
Disconnect power last.
Disconnect RS from vehicle.
18 Turn key to START position.
START
COM-BLADE-AL(DL)-CH8-EN 20191004
Doc. No.: ##65995##
Patent No. US 8,856,780 CA 2759622
INSTALL GUIDE
WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020
ALL IN ONE
DODGE/RAM
NOTICE
WARNING: READ BEFORE REMOTE STARTING THE VEHICLE
IMPORTANT
I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.
TAKE OVER PROCEDURE - TO THE VEHICLE OWNER
!Failure to follow procedure within time restriction will
result in vehicle engine shutdown.
3Take over procedure completed.
2TIME RESTRICTI N
Within 45 SECONDSfrom
previous step:
Open vehicle door.
Enter vehicle.
Close vehicle door.
Insert key into ignition.
Turn key to ON position.
Press and release BRAKE pedal.
NOTE
I All vehicle doors must be closed and locked prior to remote
start sequence.
1Press UNLOCK on after-market
remote.
TIME RESTRICTI N COMING UP !
COM-BLADE-AL(DL)-CH8-EN 20191004
Doc. No.: ##65995##
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Firstech Accessori per automobili
Firstech
Firstech 2WT13R-SF Manuale utente
Firstech
Firstech FTI-NSP2 Istruzioni operative
Firstech
Firstech 1WS2R-AF Manuale tecnico
Firstech
Firstech 2WQ9R-FM Manuale utente
Firstech
Firstech Compustar FMX RF-2WG15R-FM Manuale utente
Firstech
Firstech FLEX 2 Manuale utente
Firstech
Firstech FTI-FDK1 Manuale utente
Firstech
Firstech FTI-GMT3 Manuale utente
Firstech
Firstech BLADE Series Manuale utente
Firstech
Firstech FTI-FDK1 1A3 Manuale utente
